Genesis · 2019–today

G70 IK: every channel it can give you

18 channels are already mapped from public vehicle data. 5 more chassis and driver channels are on the car, waiting for GAINS discovery. Plus 25 Hz GPS and a motion sensor in the dongle itself.

CAN (ISO 15765)Stability control: Standard (ESC)Manual / AutomaticTheta 2.0T / Lambda 3.3TT
30channels
18 Data stream
7 Standard OBD2
5 To discover
6 Built into the dongle
OBD-II portCAN (ISO 15765)Fast, data stream capable
Internal CAN busYesWhere the chassis modules talk
GatewayTo be confirmedBetween the car's bus and the port
Stability control · ABSStandard (ESC)ABS: Standard

Channels

Every channel the IK is expected to give, by group. Filter by how it arrives.

Driver inputs

Steering angle Data stream
Accelerator pedal Data stream
Throttle position Standard OBD2
Brake pressure To discoverstability control (ESC)
Brake pedal switch Data stream
Clutch pedal To discovermanual gearbox · if fitted
Gear Data stream
Handbrake Data stream

Wheels and chassis

Wheel speed, front left Data stream
Wheel speed, front right Data stream
Wheel speed, rear left Data stream
Wheel speed, rear right Data stream
Vehicle speed Data stream
Yaw rate Data stream
Lateral g Data stream
Longitudinal g Data stream

Engine

Engine RPM Data stream
Boost / manifold pressure Standard OBD2
Intake air temperature Standard OBD2
Fuel level Standard OBD2
Battery voltage Standard OBD2

Temperatures and pressures

Oil temperature Data stream
Oil pressure To discoverengine (if the car measures it) · if fitted
Coolant temperature Standard OBD2
Gearbox temperature To discoverautomatic / dual-clutch gearbox · if fitted
Outside temperature Standard OBD2

Stability systems

ABS active Data stream
Traction control active To discoverstability control (ESC)
Stability control active Data stream
Stability control off switch Data stream

Built into the dongle, on every car

GPS speed and position 25 Hz
Lap, sector and delta times computed
Lateral and longitudinal g motion sensor
Yaw rate motion sensor
Heading and altitude GPS
Combined g (friction circle) computed

How the data gets out

Where the IK's sensors live and how GAINS reaches them.

Car's internal CAN busEngineESCSteeringDashOBD-II · CANTelemetry Dongle Pro plugs into the OBD-II port

Listen, then read the modules

Discovery first listens for the car's data stream at the OBD-II port; anything it can't hear, it requests from the modules with read-only reads.

Telemetry Dongle Pro

Discovery on your G70

The 5 channels marked “To discover” are learned once, from your car, then added for every IK owner.

  1. Plug in and identify

    The dongle finds the bus speed by listening only, reads the VIN and matches the car's data pattern to our database.

    about 1 min
  2. Guided steps, parked

    The app walks you through each control for a few seconds: wheel lock to lock, brake light then firm, throttle (engine off), clutch, every gear, handbrake, stability-control button. The dongle records what changes on the car's data stream.

    about 5 min
  3. Module read

    With the car parked, the dongle asks each module (ABS, gearbox, body) which values it can report. Read-only requests: nothing is written or changed.

    about 5–10 min, automatic
  4. Short drive

    A normal drive with a few stops, steady speeds and turns. The dongle matches unknown values against its 25 Hz GPS and motion sensor to find wheel speeds, yaw rate and g-forces.

    10–15 min
  5. Results

    Matched channels appear in the app. Anything that needs a closer look is checked by us and added later; you get a notification, and every owner of the same car gets the channel too.

    most right after the drive

First time: about 25–30 minutes, once per car. Times are estimates until measured on real cars. Discovery only listens and reads: it never writes to the car, clears codes or bypasses security.

FAQ

Can I log steering angle and brake pressure on a G70 IK through the OBD-II port?

Yes, expected on the data stream. A standard OBD2 scan tool won't show them because they aren't standard OBD2 values.

What OBD-II protocol does the G70 IK use?

CAN (ISO 15765). Its engine, stability and dash modules also share an internal CAN bus.

How long does discovery take on a IK?

The first time, about 25–30 minutes, once per car (estimate): guided steps while parked, a read-only module check and a short drive. After that the dongle recognises the car when you plug in.

Channel lists combine public vehicle data from the open-source community with the equipment this generation is known to carry. “Expected” and “To discover” channels are not yet confirmed by our own logs, and equipment varies by market, trim and year. Vehicle names identify the cars only; GAINS is not affiliated with Genesis. Specifications are pre-release and may change before launch.