Engine swaps
Swap guides.
53 guides: mounts, transmission, clearance, cooling, fuel, exhaust, wiring, tuning and the law for each engine and chassis, with a parts checklist and sources.
Engine
GM LS (Gen III / IV) 26
LSLS into BMW E30E30 · 1982-1994HardStock curb weightAbout 2,380-2,650 lb (1,080-1,200 kg) depending on body and engineMost common enginesLS1 and LS3, with T56 gearboxesGearbox optionsGM T56 or T56 Magnum, or a BMW ZF or Getrag 5-speed through an LS adapter plateLSLS into BMW E36E36 · 1990-2000ModerateStock enginesInline sixes: M50 and M52 (320i, 323i, 325i, 328i), S50 and S52 (M3)Mount-only kitsTwo engine mounts and a transmission mount, in aluminum or polyurethane bushingsOil pressure gaugeAdapters exist to fit the BMW oil pressure sender (M12x1.5) to the LS blockLSLS into BMW E46E46 · 1998-2006HardStock curb weight and balanceSedan and coupe from 2,833 lb (1,285 kg); 50/50 distribution on rear-drive carsMount kitsTwo engine mounts plus a transmission mount, for T56/CTS-V TR6060, Camaro TR6060 or AR5Engine positionIn one LQ4 build almost the whole engine sat behind the middle of the strut towersLSLS into BMW LS + BMW M guideE36 · 1992-1999HardGearboxGetrag GS7D36SG seven-speed wet dual-clutch (BMW M DCT), from the E90 / E92 / E93 M3 and other BMW M carsPublished controller pricesCANTCU €1,903 incl. VAT (one retailer); HTG GCU about $1,385 (one retailer, sold out at capture)Torque limits (gen 1 TCU)Factory TCU limited to about 15.5 bar clutch pressure; some firmware drops to neutral above about 800 Nm (590 lb-ft)LSLS into Chevrolet 3rd Gen CamaroThird generation F-body · 1982-1992ModerateCurb weight3,087-3,362 lb (1,400-1,525 kg) depending on model, per WikipediaOil panFront-clearance swap pan (302-2 required with Hooker brackets) or LS1 F-body pan with UMI mountsFactory gearboxesTH200 or 4-speed (1982); 700R4 and Borg-Warner 5-speed from 1983LSLS into Chevrolet C10 Square BodyThird-generation C/K (square body) · 1973-1987ModerateLS engine options and GM ratings5.3 LM7: 270-295 hp; 6.0 LQ4: 300-335 hp; 6.0 LQ9: 345 hp; 6.2 LS3: 430 hp, 424 lb-ft (575 N·m)LT engine options and GM ratingsLT1 6.2 L: 455-460 hp; L86 6.2 L: 420 hp and 460 lb-ft (624 N·m); L83 5.3 L: 355 hp and 383 lb-ft (519 N·m)LT fuel systemDirect injection with a cam-driven high-pressure pump; GM's LT1 control system expects a returnless low-pressure supplyLSLS into Chevrolet C4 CorvetteC4 · 1984-1996HardCurb weightAbout 3,216-3,224 lb (1985) and 3,317 lb (1992 coupe); 1,459-1,505 kgMount styles1984-91 block mounts on frame perches; 1992-96 hydraulic mounts on the frameRear axleDana 44 IRS in manual 1985-96 cars per Wikipedia; automatics differLSLS into Chevrolet G-BodyGM A/G-body (rear-drive intermediates) · 1978-1988EasyFactory engine mountsSmall-block style clamshell mounts (OE 2292 type) on frame perches; most LS kits reuse themMount routeBolt-in adapter brackets: Trans-Dapt 4206, Hooker 12643HKR, ICT EM-LS-GBDY1 or the adjustable DD-3550CTransmission crossmember1982-87 cars built for the 200-4R have a driver-side frame extension; earlier TH200/TH350 frames do notLSLS into Chevrolet OBSFourth-generation C/K (GMT400, 'OBS') · 1988-1998 pickups; 1992-1999 SUVsEasyStock V8s5.0 L L03 and 5.7 L L05 (1988-1995, throttle-body injection), then Vortec L30 and L31 (1996 on, sequential injection)L31 factory ratingWikipedia lists GM ratings for the Vortec 5700 L31 of 255-350 hp and 330-350 lb-ft across applicationsFactory automatics4L80E from 1991 (heavier GVWR), 4L60E from 1993; THM400 and 700R4 before thatLSLS into Chevrolet S10First (1982-1993) and second (1994-2004) generation · 1982-2004ModerateStock enginesFour-cylinders, 2.8 L V6 (first gen) and 4.3 L V6; no factory V8. GM rated the 1991 Syclone's turbocharged 4.3 at 280 hp2WD mount systemsHooker 71221029HKR brackets, Trans-Dapt 4516 kit, Dirty Dingo DD-LS-S2 adjustable mounts4WD mountsDirty Dingo DD-LS-S4 for 1982-2004 4WD trucks and Blazers; listed as not fitting the ZR2 chassisLSLS into Datsun 240ZS30 · 1970-1973ModerateCurb weight240Z about 2,302 lb (1,044 kg); the later 280Z about 2,875 lb (1,304 kg)Oil panRear-sump pan; kits name the 1998-2002 F-body (LS1 Camaro) pan or the C6 LS2 Corvette panTransmissionsT56 or CD009 manual; GM automatics from the Powerglide to the 4L80E with some mount kits
LSLS into Ford Fox BodyFox body (third generation) · 1979-1993ModerateCurb weight (1987)2,724 lb (1,236 kg) coupe; 2,782 lb (1,262 kg) hatchbackOil panRear-sump pan: F-body donor pan or a swap pan listed for your bracket kitBrake boosterStock vacuum booster can stay with Hooker's engine positionLSLS into Ford RangerFirst (1983-1992), second (1993-1997) and third (1998-2011) generation · 1983-2011HardStock enginesFour-cylinders and V6s only; Ford rated the 2001-on 4.0 L SOHC V6 at 207 hpMount routeUniversal weld-in LS mounts, such as ICT Billet EM-LS-UNV1 or Motobilt MB7015, on the Ranger frameTransmissionPlan on a GM 4L60E-family, 4L80E or manual; 1999-on 4L60Es bolt straight to Gen III enginesLSLS into Infiniti G35V35 (sedan and coupe) · 2003-2006 sedan, 2003-2007 coupe (US model years)ModerateModel yearsSedan 2003-2006, coupe 2003-2007Factory gearboxes5-speed RE5R05A automatic or 6-speed manual; the AWD G35x sedan was automatic onlyMount kitsSikky Stage 1 G35 package (2- or 4-door, left-hand drive); LOJ 350Z/G35 kitsLSLS into Jeep Cherokee XJXJ · 1984-2001HardCurb weight and wheelbaseAbout 3,357 lb (1,523 kg); 101.4 in (2,576 mm) wheelbaseMount kitNovak MMXJ3 (Gen III/IV LS) or MMXJ5 (Gen V LT), listed for all 1984-2001 XJ and MJOil panTruck-style LS pan with higher front sump; car pans can hit the front axle on compressionLSLS into Jeep WranglerTJ and JK · 1997-2018HardMount kitsNovak MMTJ-G (TJ/LJ), MMJK-G (2007-2018 JK), MMYJ-G3 (YJ); Hooker BHS513 brackets for the TJ via retailersManual gearboxAX15 and NV3550 can stay via Novak GMAX15 and 3504G adapters; NSG370 input is rated 272 lb-ft (369 N·m)DriveshaftsNew lengths in almost every case; Novak recommends a short-tail SYE on the NP231 and fixed-yoke shaftsLSLS into Mazda NA MiataNA · 1990-1997 (model years)HardStock engines1.6 L B6 (115 hp manual) to 1993; 1.8 L BP from 1994 (129 hp, 133 hp for 1996-97)Stock curb weightAbout 2,210 lb (1,002 kg); Wikipedia also quotes 980-990 kg for lighter trimsMounting kit weight75 lb (34 kg) as listed by the kit makerLSLS into Mazda RX-7FD (FD3S) · 1992-2002 (US model years 1993-1995)HardStock curb weight and balance2,685-2,954 lb (1,218-1,340 kg) by trim; 50:50 front-to-rearPost-swap exampleOne 6.0 L L98 FD was reported at 1,342 kg (2,959 lb) with 50:50 balanceMount kit contents (one maker)Front subframe, gearbox crossmember, bump-steer relocation kit, drive-by-wire pedal mountLSLS into Mazda RX-8SE3P · 2003-2012 (US model years 2004-2011)HardStock curb weightAbout 1,309-1,373 kg (2,886-3,027 lb) for manual cars; documented LS cars weighed about 3,200-3,240 lb (1,450-1,470 kg)Drivetrain layoutNo transmission mount: a power plant frame (PPF) ties the gearbox to the differential and must be replacedTransmissionGM T56 is the documented choice; Hinson also offers its mounts for the 4L60ELSLS into Nissan 240SXS13 · 1989-1994ModerateStock curb weight (S13)About 2,698 lb (1,224 kg)Most common enginesLS1, junkyard 5.3 L truck engines, and LS3 crate or E-ROD enginesTransmissionTremec T56 is the usual choice; the Nissan CD009 is an alternative with a weld-in tunnel clearance kitLSLS into Nissan 300ZXZ32 · 1990-1996 (US); 1989-2000 JapanModerateUS bodies1990-1996; 2+0 (T-top, non-turbo hardtop, convertible from 1993) and 2+2 T-topGearbox optionsNissan RS5R30A 5-speed via adapter, GM T56, or 350Z/370Z CD00xOil panLOJ 6.5 qt (6.2 L) baffled steel pan with pickup and dipstickLSLS into Nissan 350ZZ33 · 2003-2008ModerateStock curb weight (coupe)About 3,188-3,247 lb (1,446-1,473 kg) for 2003-04 coupes, depending on trimMost common enginesLS1 and LS6 from the Camaro, Firebird, GTO and C5 Corvette; LS3 for drive-by-wire buildsRear differentialViscous LSD on Enthusiast, Touring, Track and Nismo trims; base cars have noneLSLS into Porsche 944944 · 1982-1991HardBellhousingManual C5 Corvette bellhousing bolted to an adapter plate on the 944 torque tubeFactory layoutFront engine, rear transaxle; Porsche quoted 50.7% front and 49.3% rearKit fitment (one maker)944, 944 S, 944 Turbo and 951 with the OEM manual transmission, 1982-1991LSLS into Subaru BRZ / Scion FR-S / Toyota 86ZN6 / ZC6 (first generation) · 2013-2020HardCurb weight2,762-2,822 lb (1,253-1,280 kg) for the 2013 BRZ, depending on trim and gearboxTransmissionSikky lists T56, T56 Magnum, TR6060 and CD009 options with matching driveshaftsOil panFront-sump LS pan: Sikky's own pan, or a Moroso front-sump pan with ICT mountsLSLS into Toyota TacomaFirst generation (N140-N190) · 1995-2004HardStock transmissions5-speed manuals (R150F behind the V6) and the 4-speed A340E (2WD) or A340F (4WD) automatic4x4 transfer case routeAdvance Adapters lists a 4L60E to Toyota Truck 23-spline gear-drive (RF1A) adapter, 50-5761Oil pan2WD: a front-sump pan fit one build; 4WD: a custom pan is needed to clear the front differentialLSLS into Volvo 240200 Series (240/242/244/245) · 1975-1993HardCurb weight2,840 lb (1,288 kg) for a 1989 US-spec 240, fully fueledFront suspension and steeringMacPherson struts with rack-and-pinion steeringTransmissionGM T56 manual is the press-documented choice

Honda K-series 10




Toyota JZ 6
2JZ2JZ into BMW E46 3 SeriesE46 · 1999-2006HardRecommended engines2JZ-GTE (turbo) for power; 2JZ-GE (NA) for budget or a later turbo buildConstructionCast-iron block, aluminum head, belt-driven DOHC inline sixFactory injectors (GTE)550 cc/min export; 440 cc/min Japan
2JZ-GTE2JZ-GTE into Lexus IS300XE10 · 2001-2005ModerateToyota 2JZ-GTE rating (Japan, 1993)280 PS (276 hp, 206 kW) and 44.0 kg-m (318 lb-ft, 431 Nm)Oil panIS300 is a front-sump chassis; Supra and SC300 pans are rear-sumpThrottleElectronic throttle (ETCS-i); no pedal cable2JZ2JZ into Nissan 240SX S13S13 · 1989-94ModerateConstructionCast-iron block, aluminum head, belt-driven DOHC inline sixFactory injectors (GTE)550 cc/min export; 440 cc/min JapanTransmissionsToyota R154; Nissan CD00x via adapter; factory V160/V161 (rare)1JZ-GTE1JZ-GTE into Nissan 240SX S14S14 · 1995-98ModerateRecommended engine1JZ-GTE VVT-i single turbo (1996-on)Older option1JZ-GTE twin turbo (1990-96)Engine weight vs stockNot published in sources found2JZ2JZ into Nissan 2JZ + BMW M guideS13 · 1989-94HardGearboxGetrag GS7D36SG seven-speed M DCT from the E90 / E92 / E93 M3 (gen 1)2JZ-GTE stock torque44.0 kg-m (318 lb-ft, 431 Nm), Japanese ratingEngine mountsS13/S14 JZ swap mounts exist (ISR); gearbox mount must suit the DCT2JZ2JZ into Toyota MK3 SupraA70 (MA70 / JZA70) · 1986.5-1993EasyFactory sister pathJapan-only JZA70 used the 1JZ-GTE 2.5 L twin turbo (1990-1993)Oil panRear-sump JZ pan required; the A70 is a rear-sump chassisFactory gearboxesW58 (NA), R154 (turbo) or A340E four-speed automatic

Ford Coyote 4
CoyoteCoyote into Ford Dentside F-100 / F-150Sixth generation (Dentside) · 1973-79ModerateBest engine for most buildsGen 2 Coyote (2015-17) with a 6R80Truck-donor option2011-17 F-150 5.0Engine widthJust over 29 in (737 mm) valve cover to valve coverCoyoteCoyote into Ford Early BroncoFirst generation (early Bronco) · 1966-1977HardFactory engines170 and 200 cu in sixes; 289 V8 from 1966, 302 V8 from 1969 to 1977Wheelbase92 in (2,337 mm)Coyote sizeJust over 29 in (737 mm) wide; about 430 lb (195 kg) as weighed by EngineLabs
CoyoteCoyote into Ford Fox Body MustangFox · 1979-93ModerateBest engine for most buildsGen 2 Coyote (2015-17)Engine widthJust over 29 in (737 mm) valve cover to valve coverTransmission optionsTremec-style manual or 6R80 / 10R80 automatic
CoyoteCoyote into Ford SN95 and New Edge MustangSN95 / New Edge · 1994-2004ModerateBest engine for most buildsGen 2 Coyote (2015-17)Coyote weightAbout 430 lb (195 kg) as measured with flywheel, without water pumpEngine widthJust over 29 in (737 mm) valve cover to valve cover


Mopar Gen III Hemi 2
HemiHemi into Jeep JKJK · 2007-18HardLater kits5.7 and 6.4 Hemi kits for 2012-14 JKsEngine weight vs stockNot published in sources foundTransmissionHemi-family five-speed automatic, such as the 545RFEHemiHemi into Jeep Wrangler TJTJ / LJ · 1997-2006HardUsual donor2003-08 Ram 5.7 Hemi truck engine with 545RFETransfer caseStock NP231J can be retained with a 545RFE and its adapterOil panGen III truck rear-sump pan from the donor engine
Nissan RB 2
RB25DETRB25DET into Nissan 240SX S13S13 · 1989-94ModerateRecommended engineRB25DET (R33 or R34 NEO)Budget alternativeRB20DETEngine weight vs stockNot published in sources foundRB26DETTRB26DETT into Nissan 240SX S14S14 · 1995-98HardNissan rating206 kW (280 PS) at 6,800 rpm; 353 Nm (260 lb-ft) at 4,400 rpm (1989 BNR32)Displacement2,568 cc (156.7 cu in) inline six, 86 mm bore x 73.7 mm strokeOil panThe AWD RB26 pan will not clear; use a rear-drive pan or a modified RB26 pan

