At a glance
The key numbers and parts, with the source on each tile.
Honda rated the 1.5 L at 109 hp (2007), 117 hp (2009) and 130 hp (2015 direct-injected)
Sourced2223242,432 lb / 1,103 kg (2007), 2,489 lb / 1,129 kg (2009), 2,513 lb / 1,140 kg (2015 LX)
Sourced222324- Honda K-series manual matched to the kit: RSX/02-11 Si for GD
- RSX, Accord/TSX or later Si for GE
- Accord/TSX or later Si for GK
- Hasport axle sets: GD with RSX/Si intermediate shaft
- GE/GK with the longer K24 intermediate shaft
Recommended engines
- K24Z (K24Z7 Civic Si) · The K24Z3 (2009-14 TSX) and K24Z7 (2012-15 Civic Si) are the default for GE and GK Fits: harness makers sell jumpers for their engine harnesses and ECUs, and Hasport's GKK kits for the GK only list K24-family gearboxes.
- K20Z1 / K20Z3 · The K20Z3 and its 06-11 Civic Si six-speed suit the GD and GE: Hasport's GDK kit requires an RSX or 02-11 Si gearbox, and Hybrid Racing makes Fit shifter cables specifically for the K20Z3 transmission.
- K24A2 (TSX) · A TSX K24A2 works in a GD with an 04-08 TSX engine harness and jumper; it also suits the GE through the 8th-gen Si jumper, but check that Hasport's rear bracket matches your block before choosing it.
Mounts
For a k swap Honda Fit, Hasport covers all three US generations.
- GDK brackets only
- Reuses the stock Fit rubber mounts
- RSX or 02-11 Civic Si gearbox
The GD kit is brackets only and bolts the K-series to the stock Fit rubber mounts. The GE and GK kits use Hasport's dual-height system, so the head sits in the same place with a K20 or K24 and the same header and intake fit either block.123
Pick the kit by gearbox, not engine. GEK1 takes the RSX or 02-11 Civic Si box, GEK2 the 03-07 Accord or 04-08 TSX box, and GEK3 the 08-13 Accord, 09-14 TSX or 12-15 Si box. The GK kit lists only the Accord/TSX and later Si gearbox families.23
Hasport warns that the GEK rear brackets for the Accord, TSX and 12-15 Si gearboxes do not fit US K24A1, K20A2, K20A3 or K20Z1 blocks or their JDM versions. A retailer adds that a K24 may need a timing-cover post mount. Bushings run from 62A street to 94A race; stiffer ones pass more vibration into the cabin.2166
Hybrid Racing's listing now sells the GD kit as one part number for K20 and K24, while Hasport's own site still lists separate GDK20 and GDK24 kits. One GD owner found the stock rubber mounts let the engine rock and rub, so builders stiffen or replace them. Safety: support the engine on a hoist and the car on rated stands.Low5121
Transmission
The Fit keeps a transverse front-drive layout, so the K-series gearbox bolts straight to the engine and drives the front axles.
- Hybrid Racing HYB-SCA-01-42
- Reuse the Fit center bracket and floor seal
Braided line kits made for K-swapped Fits with a top-port master cylinder
Sourced · medium20The gearbox decides the mount kit, the axle set and the shifter cables, so choose it first. The GD kit accepts only the RSX or 02-11 Civic Si manual.12
Stock Fit shifter cables are too short for where the K gearbox sits, and the end links do not line up. Hybrid Racing sells longer cables for the K20Z3 gearbox and a separate set for K24Z3, K24Z7, K20Z4 and FD2 gearboxes; both keep the stock Fit shifter and reuse the factory center bracket and floor seal.Medium98
Builders have also used Accord cables with an Accord shifter box on an adapter plate, later shortening cables to suit the Fit box. That route needs fabrication and is reported only by an owner build log.Low21
If you use an engine harness from an automatic TSX or Accord, the speed sensor plug differs from the manual gearbox's sensor; 2NRS sells a conversion lead for this. Clutch hydraulics need a line from the Fit master cylinder to the K slave; braided lines made for the swap need a top-port master and slave.Medium1120
Clearance
Hasport designs its Fit kits for axle alignment plus ground and hood clearance with the listed gearboxes, so stay with the gearbox and block combination your kit specifies. Mixing parts moves the engine and changes every other clearance.235
In a GD, one owner had to cut the front core support to clear a TSX intake manifold, and notes that a smaller RSX Type S manifold reduces the cut. The same build reports the manifold hits the stock radiator fans. Treat these as one car's findings and mock up before cutting.Low21
Every Fit generation uses electric power steering, so there is no steering pump to relocate. Builders run the K-series belt without a pump, using an idler in its place; one owner used the EP3 Civic Si part.Low222421
Cooling
Plan the radiator, fans and hoses together with the intake manifold.
One GD owner kept the stock radiator but found the K-series manifold hit the stock fans, so builders fit slim pusher fans ahead of the core or move the radiator and condenser forward to keep pullers.Low21
Heater hoses are a common surprise. A K20Z3, K24A2 or K24A4 has a 3/4 in (19 mm) heater outlet while the Fit heater core fitting at the firewall is 5/8 in (16 mm), so you need a step adapter and a short length of 3/4 in hose.Medium17
Air conditioning can stay. 2NRS sells an adapter that bolts Fit A/C lines to a 04-08 TSX compressor and jumpers that plug TSX compressors into the GE Fit body harness. Have the system evacuated and recharged by a shop with recovery equipment.Medium19
Fuel
Honda puts the Fit's fuel tank under the front seats, which frees the rear floor for the Magic Seat.
The pump therefore sits mid-car, and you service it from the cabin side of the tank rather than under the rear seat.Medium252624
On the GE, 2NRS sells a braided line and an OEM 9th-gen Civic line that plug into the stock hard line at the firewall and connect to a K-series rail. Keep the system returnless unless you add a return line and regulator.Medium18
We found no source rating the stock Fit pump against K-series demand. Measure flow and pressure at the rail before tuning, and size any replacement with the fuel pump flow calculator. Safety: relieve pressure, disconnect the battery and keep an extinguisher close when opening fuel lines.Low1823
Exhaust
The header is the hardest part to source for a Fit swap.
One GD owner calls it the toughest item and ran a custom header made for a K-swapped Fit; we found no maker product page for a Fit header to cite.Low21
Because Hasport's dual-height GE and GK mounts put the head in the same place for K20 and K24 blocks, one header design fits either block in those kits. Ask the header builder which mount kit and gearbox it was made around.Medium23
Route the downpipe clear of the steering rack, axles and shifter cables, and keep heat shielding between the exhaust and the center-mounted fuel tank area under the front seats.Low258
Electrical
The Fit's body systems share data with the engine computer over CAN.
- 8th-gen Si ECU and harness: tach, speedo and OBD port work
- Cruise may not
- A CAN error remains
09-14 TSX or 08-12 Accord harness and ECU: the maker's choice for the most Fit compatibility and best chance of passing emissions
Sourced · medium11- 12-15 Civic Si ECU: Fit tach does not work
- EPS, traction control, ABS and TPMS warning lights from CAN incompatibility
Honda's 2015 Fit pairs its electric steering with stability control, so a donor computer that does not speak the Fit's messages brings warning lights. The donor ECU you pick decides what keeps working.Medium2413
For the GD, a jumper adapts the Fit to an 04-08 TSX engine harness, with a drive-by-wire pedal extension and an Element charge harness. One owner found the 08 TSX and 08 Fit share drive-by-wire and multiplex layouts, with ECU plugs A and B matching and D and E needing rework.Medium1421
For the GE there are three jumpers. The 8th-gen Si route suits K20A2, K20Z1 and K24A-family engines; the TSX/Accord route suits K24Z engines and keeps the most features; the 9th-gen Si route works but logs a CAN error. The Si jumpers need the ECU A connector fully repinned.Medium101112
With a 12-13 Civic Si ECU in a GE, the ECU, GE dash and keys must be married through Honda's all-keys-lost procedure at a dealer or locksmith. A 14-15 push-button Si ECU will not work in a GE. In a GK, use the 14-15 ECU for push-button cars and the 12-13 ECU otherwise.Medium1213
Chassis
Honda lists the 2009 manual Fit at 62% front and 38% rear weight distribution.
A K-series and its gearbox add weight over the front axle, so expect more understeer and more load on front tires, bearings and brakes. We found no sourced figure for the finished swap.Medium2328
Honda fitted 10.3 in (262 mm) vented front discs and 7.9 in (201 mm) rear drums to the 2009 and 2015 Fit. Plan a brake upgrade with the swap. Tailored Chassis Solutions, which builds K24Z7 Fits for endurance racing, pairs its swaps with suspension and brake work.Medium232427
The axles must match the intermediate shaft. Hasport's GD set works with the RSX or Si intermediate shaft and is rated for street use, not drag racing. Its GE and GK set suits the longer K24 intermediate shaft and will not work with the shorter K20 shaft.415
Tuning
Most Fit swaps keep a factory Honda K-series computer, re-calibrated with commercial tools, because it already runs the drive-by-wire throttle, VTEC and cam phasing. Harness makers note that immobilizer handling is part of that calibration on swapped Fits. A standalone ECU is the alternative, but then the Fit's CAN messages must come from somewhere else.Medium132128
Start from the donor calibration and correct fueling from wideband logs across load and rpm. VTEC crossover and cam angles are calibration choices, not fixed numbers. Advance ignition only as far as knock monitoring and logged results support; no single timing figure suits every engine and fuel.Medium28
Log lambda, manifold pressure, coolant and intake temperature, knock activity and cam angle on the first drives. Keep the stock oxygen sensor type the donor ECU expects; the 2NRS jumpers list the donor's OEM sensors as required parts.Medium1110
Legal
This section is general information, not legal advice.
- EPA's 2020 tampering policy asks for a documented basis that the change does not raise emissions
- California sends engine changes to a BAR Referee
StVZO section 19(2): the operating permit lapses if a change worsens exhaust or noise or endangers road users
Sourced32State registration authorities apply VSB 14 Section LA (engine) to engine changes
Sourced · medium33In the US, EPA's 2020 enforcement policy looks for a documented, reasonable basis that a modification does not increase emissions. California's BAR treats a K-series in a Fit as an engine change that must pass a Referee inspection against the applicable smog requirements and carry a Referee label.2930
In the UK, update the V5C with DVLA when the engine or cylinder capacity changes. DVLA asks for evidence such as a receipt showing the new engine number and capacity, or an inspection report made for insurance purposes. Tell your insurer about the swap as well.31
In Germany, StVZO section 19
- says the operating permit lapses when a change endangers road users or worsens exhaust or noise, so an engine swap needs an officially recognized inspector's approval before road use. In Australia, ask your state registration authority, which applies VSB 14 Section LA to engine installations.Medium3233
Parts checklist
Tick what you have; the list is saved in this browser.
Order of work
10 stages, in the order most builds follow.
- Pick the generation and donorDecide the engine, gearbox and donor ECU together, because the Fit generation limits which gearbox families and jumper harnesses work.
- Order matched partsOrder the mount kit variant, axles, intermediate shaft, shifter cables, clutch line and jumper harness for that one gearbox and ECU combination.
- Prepare the donorCheck compression and leak-down, replace worn chain tensioner parts and fit fresh seals, clutch and flywheel while the engine is out.
- Remove the L-seriesSupport the car on rated stands, drain fluids, label connectors and remove the engine and gearbox as a unit with a hoist.
- Fit mounts and drivetrainInstall the brackets and mounts, lower the K-series in, then fit the intermediate shaft, axles and shifter cables and check axle plunge.
- Plumb cooling and fuelFit the radiator, fans and hoses with the heater adapter, connect the fuel line to the rail and pressure-test it before the first start.
- Wire the carRepin and connect the jumper harness, charge harness and grounds, then confirm power, ground and CAN wiring with a meter.
- Pair keys and first startHandle the immobilizer through key pairing or calibration, prime oil pressure, then start and check for leaks and warning lights.
- Tune and verifyLog with a wideband, correct fueling, check knock activity and confirm speedometer, tachometer and stability-control behavior.
- Register and insureComplete emissions inspection or engineering approval and update registration and insurance for your region.
Common problems
Symptom, cause and the usual fix.
| Problem | Cause | Fix |
|---|---|---|
| GE rear mount bracket will not bolt to the block | Hasport's GEK2 and GEK3 rear brackets do not fit US K24A1, K20A2, K20A3 or K20Z1 blocks | Use a K24Z block with GEK2/GEK3, or choose GEK1 with an RSX or 02-11 Si gearbox for early blocks.2 |
| Shifter feels vague or binds | Stock Fit cables are too short for the K gearbox position and the end links do not line up | Fit swap-length cables made for your exact gearbox and reuse the Fit center bracket and floor seal.Medium89 |
| Axles too short or too long | The axle set was made for the other intermediate shaft length | Match axles to the shaft: Hasport's GE/GK set needs the long K24 intermediate shaft; its GD set uses the RSX or Si shaft.154 |
| GK shows EPS, ABS, traction control and TPMS lights, and the tach is dead | The 12-15 Civic Si ECU does not exchange the CAN messages the GK expects | Accept and document the lights with the jumper maker's guidance, or choose a donor and harness route that keeps the Fit's CAN messages; never drive with steering assist faults unresolved.Medium1324 |
| GE will not start with a Civic Si ECU | The ECU, dash and keys are not married, or a 14-15 push-button ECU was used | Use a 12-13 Si ECU and have a dealer or locksmith run the all-keys-lost pairing for the ECU, GE dash and keys.Medium12 |
| Heater hose will not fit the firewall | K-series heater outlet is 3/4 in while the Fit heater core fitting is 5/8 in | Fit a 5/8 in to 3/4 in adapter and a short piece of 3/4 in hose.Medium17 |
Frequently asked
Which Honda Fit generation is easiest to K-swap?
The GE (2009-14) has the widest choice. Hasport's GEK kit takes three gearbox families, and 2NRS sells three GE jumper harnesses, including a TSX/Accord route it says keeps the most Fit features working. The GD kit accepts only RSX or 02-11 Si gearboxes, and GK swaps with a Civic Si ECU lose the tachometer and show CAN warning lights.Medium211113
What transmission do I need for a Honda Fit K-swap?
Use a K-series manual that your mount kit lists. The GD kit needs an RSX or 02-11 Civic Si gearbox. GE kits accept RSX/02-11 Si, 03-07 Accord/04-08 TSX, or 08-13 Accord/09-14 TSX/12-15 Si boxes. GK kits list only the Accord/TSX and later Si families. Match shifter cables to the same gearbox.1238
What axles fit a K-swapped Honda Fit?
Buy axles matched to your chassis and intermediate shaft. Hasport's GD set works with its GDK mounts and the RSX or Si intermediate shaft and is meant for street use. Its GE/GK set suits the longer K24 intermediate shaft from a K24A2, K24Z3 or K24Z7 and will not work with the shorter K20 shaft.415
Does the power steering still work after a Fit K-swap?
Usually, because the Fit uses electric power steering with no engine-driven pump. It does rely on data from the engine computer, though. In a GK with a 12-15 Civic Si ECU, 2NRS reports an EPS warning from CAN incompatibility, so check steering assist carefully before driving and choose the donor ECU with this in mind.Medium2413
Will the gauge cluster work in a K-swapped Fit?
It depends on generation and donor ECU. In a GE with an 8th-gen Si ECU, the tachometer, speedometer and OBD port work but a CAN error remains. A 9th-gen Si ECU in a GE also runs the tach and speedo. In a GK with a 12-15 Si ECU, the Fit tachometer does not work.Medium101213
Is a K-swapped Honda Fit street legal?
It can be, but rules vary and this is not legal advice. In California the car needs a BAR Referee inspection for the engine change. The UK requires a V5C update with evidence, Germany needs inspector approval under StVZO section 19, and Australian states apply VSB 14. 2NRS says a TSX/Accord harness route gives the best chance of passing emissions.Medium3031323311
Related
Sources
33 sources
- GDK20 and GDK24 mount kits for 06-08 Honda Fit (product pages) · Hasport Performance · vendor-doc · retrieved 2026-10-27
- GEK K-series swap mounts for 2009-2014 Fit (product page) · Hasport Performance · vendor-doc · retrieved 2026-10-27
- GKK K-series swap mounts for 2015-2019 Fit (product page) · Hasport Performance · vendor-doc · retrieved 2026-10-27
- HP-GDKAX axle set for K-series swap in 07-08 Fit (product page) · Hasport Performance · vendor-doc · retrieved 2026-10-27
- Hasport GDK K Swap Engine Mount Kit for 07-08 Honda Fit (retailer listing) · Hybrid Racing · vendor-doc · retrieved 2026-10-27
- Hasport K Swap Engine Mounts for 09-14 Fit (retailer listing) · Hybrid Racing · vendor-doc · retrieved 2026-10-27
- Hasport K Swap Engine Mount Kit for 15-20 Fit (retailer listing) · Hybrid Racing · vendor-doc · retrieved 2026-10-27
- K Swap Fit Shifter Cables for K24Z/K20Z4/FD2 (product page) · Hybrid Racing · vendor-doc · retrieved 2026-10-27
- K20Z3 Trans K Swap Shifter Cables for 07-13 Fit (product page) · Hybrid Racing · vendor-doc · retrieved 2026-10-27
- Fit GE to 8th Gen Si Jumper (product page) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- Fit GE to TSX or Accord Jumper (product page) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- Fit GE to 9th Gen Si Jumper (product page) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- Fit GK to 9th Gen Si Jumper (product page) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- Fit GD to K-series Jumper, Element charge harness and DBW extension (product pages) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- Fit K Swap Axles (Hasport, GE/GK, long intermediate shaft) (product page) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- Fit GE and Fit GK K-series Swap Mounts (retailer pages) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- Heat Hose Adaptor 5/8 in to 3/4 in (product page) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- Fuel Line for K-swapped GE Fit and CR-Z, and OEM 9th gen Civic fuel line (product pages) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- AC Line Adapter and Fit & CRZ AC Compressor Jumper (product pages) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- Clutch Line for K-swapped Fit or CR-Z (product page) · 2NRS LLC · vendor-doc · retrieved 2026-10-27
- K20 / K24 Honda Fit Swap Info (GD3) (owner build notes) · PBOMERS.COM · community · retrieved 2026-10-27
- 2007 Honda Fit Press Information · American Honda Motor Co. · oem · retrieved 2026-10-27
- 2009 Honda Fit Specifications and Features · American Honda Motor Co. · oem · retrieved 2026-10-27
- 2015 Honda Fit Overview (press kit) · American Honda Motor Co. · oem · retrieved 2026-10-27
- Honda Fit (first generation) · Wikipedia · reference · retrieved 2026-10-27
- Honda Fit · Wikipedia · reference · retrieved 2026-10-27
- Honda Fit with a K24 (Tailored Chassis Solutions endurance car) · Engine Swap Depot · press · retrieved 2026-10-27
- Honda K engine · Wikipedia · reference · retrieved 2026-10-25
- Tampering Policy: The EPA Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
- Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
- Change vehicle details on a V5C: what evidence to give · GOV.UK (DVLA) · standard · retrieved 2026-10-25
- Strassenverkehrs-Zulassungs-Ordnung (StVZO) section 19: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
- Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government, Department of Infrastructure · standard · retrieved 2026-10-25

