Power distribution · gearbox · body

GAINS PDM2

Every load. Every gear.

The ECU2's partner in the same double-wide shell: relay-free, fuse-free power for the whole car, native gearbox control, and windows, locks and wipers on configurable bridges. It talks to ECU2 over the powered CAN port and works on its own with any ECU.

Launch EditionFirst 100 units
Est.$899$1,099 after launch

No payment to reserve · Coming 2027 · Estimated price, confirmed before orders open

Illustrative model: the ECU2 shell with the PDM insert (battery stud, 25 A connector, USB-C) and the same display. Drag to turn it.

Every load, watched

No relays. No fuses.
Just answers.

Each output measures its own current and switches itself off in microseconds on a fault, then retries the way you set. The box keeps a running budget against its 150 A limit.

Box total0 A of 150 A

All loads inside their limits

  • Fuel pump0 A
  • Fan 10 A
  • Fan 20 A
  • Ignition coils0 A
  • Injectors0 A
  • Headlights0 A
  • Water pump0 A
  • Wipers0 A
  • Gearbox solenoids0 A
  • Dash + displays0 A
  • Brake lights0 A
  • Accessory0 A

Illustration with synthetic currents.

Rule

Fan 1 on when coolant > 95 °C, off below 90 °C. Fails on if the sensor is lost.

Coolant88.0 °CFan 1 off

Logic, on the module

Rules you set once.
Run every second.

Fans by coolant temperature, the fuel pump primed and timed out, lights on with the ignition. Rules run on PDM2 itself, so they keep working with the phone in your pocket, and they fail safe: fans fail on.

Gearbox control (planned)

Paddle up.
ECU2 does the rest.

On sequential and paddle-shift builds, PDM2 fires the gearbox solenoids while ECU2 cuts torque for a few tens of milliseconds, then brings it straight back. Automatics run on PDM2's own shift logic.

Gear2
PaddleECU2 cuts torquePDM2 fires the solenoidsTorque back
Up to30protected power outputs
Four25 Aoutputs for fans and pumps
Drives8current-controlled gearbox solenoids
Box limit150 Acontinuous, watched in firmware
What it's for

Restomods,
fully wired.

LS, LT and Coyote swaps first, then motorsport. ECU2 + PDM2 covers a standalone build end to end, except direct injection.

No relays, no fuse box

Battery stud in, protected outputs out: main relay, fuel pump, fans, starter, lights and accessories, each with its own current sense and electronic fuse.

Gang outputs in the app

24 single-pin smart outputs of about 8 A. Join two or three for a bigger load; each leg keeps its own sensing, so a lost pin in a gang is caught. A heat budget per connector keeps the pins inside their rating.

Gearbox control (planned)

Direct-drive automatics such as the 4L60E–4L80E and 6R80 on its own solenoid control and shift logic, and sequential paddle shift with ECU2 ignition cut and throttle blip over CAN.

Windows, locks, wipers

Four configurable bridges: motor drive with stall cut-off for windows, locks and 2-speed wipers, or extra protected 12 V outputs when you don't need them.

Second wideband

A second Bosch LSU 4.9 controller for bank-to-bank fuelling on V engines.

Same screen, same app

The same 2.4-inch display and button as ECU2: per-channel current, faults, gearbox state and gear.

Inputs and outputs

What it
switches.

Two Superseal 34 connectors keyed apart from ECU2's, plus a 4-way high-current connector on the insert. Counts are the plan; the pin table is set after the ganging study.

425 A outputsHigh-side, on the Deutsch 4-way on the insert.
24Smart outputsSingle-pin ~8 A high-side, gangable in the app, current-sensed.
4BridgesWindows, locks, wipers, or 8 configurable high- / low-side outputs.
8Gearbox solenoidsCurrent-controlled low-side for shift and line-pressure valves.
6Speed inputsInput and output shaft speed, 4 wheel speeds.
3CAN busesGAINS link, vehicle, and a private gearbox bus.
Applications

Any 12 V car.
Any ECU.

The PDM2 switches and protects loads; it does not control the engine, so it is not tied to one engine or car.

Any12 V vehicle
28protected outputs plus 4 bridges (concept)
AnyECU, or none
  • Pre-release: GAINS hardware is concept design with target specifications.
  • Fitment is derived from published pinouts, harness makers' published fitment and engine specifications.
  • Not yet fit-tested or validated on any vehicle.
  • Check your exact car in the planner before you buy anything.

What it powers

Fuel pumps and fans

Four 25 A outputs with soft start and PWM. The pump primes and times out by default; fans fail on.

Lights and accessories

24 single-pin smart outputs of about 8 A, each current-sensed. Gang two or three in the app for a bigger load.

Windows, locks, wipers

Four configurable bridges with stall cut-off, or extra protected outputs when you don't need them.

Gearbox control (planned)

Eight current-controlled solenoid outputs and speed inputs for automatics, and paddle shift with ECU2 cut and blip.

Second wideband

A second Bosch LSU 4.9 controller for bank-to-bank fuelling on V engines.

Works alongside

Safety

Safe by
default.

Off until configuredEvery output stays off at power-up until its configuration has loaded and checked.
Fail-safe loadsThe fuel pump primes and times out; fans fail on; motor drives stop at stall.
Shift guardrailsPer-gear limits, cut timeouts and a defined failsafe if the link to ECU2 drops. Engineer review and logs before any gearbox is listed as supported.
No phone in the loopRules run on the module; the phone and the display only configure and monitor.
Specifications

Every number
is a target.

Concept specification. Each row carries its status; nothing here is validated hardware yet.

Plan

Processor
NXP S32K314, the same as ECU2; ESP32-S3 for the display, app link and USB
Power outputs
4 × 25 A, 24 × ~8 A single-pin (gangable), 4 configurable bridges; 150 A box limit
Gearbox
8 current-controlled solenoid outputs; ISS / OSS, TFT, range switch, paddle and gear-position inputs; private gearbox CAN bus
Inputs
Switch / analog inputs (resistor-ladder capable), 4 wheel speeds, second wideband, ignition / wake, 5 V sensor supply
Connectors
2 × TE Superseal 34 (keyed or colour-banded apart from ECU2), Deutsch DTP 4-way and M6 battery stud on the insert
Display
Same 2.4" panel, window and button as ECU2
Housing
Double-wide billet 6061 shell shared with the PDM2: about 150 × 97 mm (113 with the connectors standing proud), 37 mm tall over the connector band and 20.5 mm over the low rear deck; 2 mm walls; machined peripheral insert to the right of the connectors; the base plate is the heat sink

Launch Edition

Est.$899 for the first 100. Then $1,099.

  • No payment to reserve
  • Coming 2027
  • Served in order: the first 100 reservations hold Est. $899
What do I pay now?

Nothing. A reservation is a place in the queue for the Launch Edition. We email you before orders open, and you decide then.

What happens after the first 100?

Reservations are served in the order they were made. The first 100 units are the Launch Edition at Est. $899; after that the PDM2 is an estimated $1,099.

Why is the price an estimate?

The design is still being finished. We confirm the final price to everyone in the queue before orders open, and you can walk away then.

When does it ship?

Coming 2027 is the target. Reservation holders hear first if that moves.

Every load.
Every gear.

PDM2 · Launch Edition Est. $899

Reserve at Est. $899

Coming soon. Specifications and images are pre-release and may change before launch. Brand and model names identify compatible equipment only; GAINS is not affiliated with their makers.