A screen on the ECU
A 2.4-inch, 500-nit display in the lid, readable in a footwell. The default page shows engine state, sync, RPM, battery and faults at a glance; one sealed button pages through the rest. Brightness follows the light.
The whole engine. In plain sight.
The GAINS ECU: two connectors, A and C, with pin functions that follow the published Haltech Nexus S3 wiring diagram, so S3-style harnesses and adapters can be used. Full sequential fuel and spark for 4 to 8 cylinders, drive-by-wire, and a built-in 2.4-inch display that tells you what the engine is doing and which pin to check, standing at the car.
No payment to reserve · Est. April 2027 · Estimated price, confirmed before orders open
It learns your engine
ECU2 measures what the engine actually needs and moves the fuel table toward it in small steps, inside limits you set. Anything bigger becomes a proposal you approve, and the ECU checks it again before it runs.
Learning inside your limits: small, bounded steps while you drive.
Illustration on a synthetic engine. Learning and approvals are how ECU2 is designed to work; not yet validated on a vehicle.
Drive-by-wire, built in
Four half-bridges run up to two electronic throttles. Every throttle reports its position twice, on mirrored tracks. ECU2 compares them every cycle, and if they disagree a hardware watchdog cuts the motors and the throttle springs shut.
Sensors agree: tracking the pedal
Plug-and-play
Connector pin functions follow the published Haltech Nexus S3 wiring diagram, so harnesses built for it plug straight in. Pick the route that fits your car.
A harness built for the published Nexus S3 pinout plugs straight into the car's own loom. No cutting, nothing written to the factory ECU.
80 cars in our catalog have a published plug-and-play route today. Find yours →
One system
Every GAINS module plugs into ECU2's powered CAN port with one cable, and shows up on its display and in the app.
ECUs in this class show three or four status lights, so every question needs a laptop or a phone. ECU2 has a 2.4-inch screen in the lid that tells you what is wrong and which pin to check, standing at the car.
RPM · SYNC OK · LAMBDA 0.98
2.4" · 240 × 320 · 500+ nits · auto-dim
Illustrative pages with sample values. One sealed button pages through them; a serious fault takes over the screen.
One ECU for 4-, 6- and 8-cylinder engines, cable or drive-by-wire. ECUs in this class show three or four status lights; ECU2 shows you the answer.
A 2.4-inch, 500-nit display in the lid, readable in a footwell. The default page shows engine state, sync, RPM, battery and faults at a glance; one sealed button pages through the rest. Brightness follows the light.
Crank without firing and the screen ticks through it in order: battery while cranking, crank signal, cam sync, fuel pump, injector pulses, spark, MAP drop. The most common support call, answered at the car.
"Coolant temp sensor open circuit. Check connector C pin 14, expect 0.5–4.5 V", with the live value. A pin inspector shows every input and output with its pin, so most harness faults need no multimeter.
On first power-up it lists, per connector, which sensors it found, which are missing and which look wrong, before the first crank.
Four half-bridges run up to two electronic throttles, with pedal and throttle sensors on the ECU's own inputs and a windowed watchdog that cuts the motors in hardware on a fault.
Connector A and C pin functions follow the published Nexus S3 wiring diagram. Firmware, calibration and CAN are GAINS' own.
A sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
The on-ECU adaptive layer, the app, logging and your limits. The display only shows; anything it asks for is re-checked by the engine controller.
Two Superseal 34 connectors, A (Key 1) and C (Key 2).
Engines and cars the ECU2 can control, from the planner's rules and the published channel counts.
One answer per car, straight from the planner's rules: what the ECU2 needs to run it.
Try
264 cars in the planner · popular picks below
1997-04LS1
ECU2
Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.
1998-02LS1
ECU2
Full sequential fuel and spark for this 8-cylinder on a cable throttle, with the wideband built in.
1998-02LS1
ECU2
Full sequential fuel and spark for this 8-cylinder on a cable throttle, with the wideband built in.
1999-075.3 LM7 / L59 / LY5 (Gen III/IV truck)
ECU2
Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.
1999-06LS1
ECU2
Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.
1987-935.0 / 302 + 5.8 / 351W
ECU2
Runs this 8-cylinder's injectors and its distributor on one ignition output, with the wideband built in.
2011-17Coyote Gen 1
ECU2
Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.
2002-08Barra 4.0 Turbo (XR6T / F6)
ECU2
Full sequential fuel and spark for this 6-cylinder, and its electronic throttle, with the wideband built in.
2005-5.7 Hemi (Eagle, VVT 2009+)
ECU2
Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.
2009-5.7 Hemi (Eagle, VVT 2009+)
ECU2
Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.
1994-01B18C (GS-R / Type R)
ECU2
Runs this 4-cylinder's injectors and its distributor on one ignition output, with the wideband built in.
2017-K20C1 2.0T (Type R FK8 / FL5)
ECU2 + DIRoadmap
Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.
Filtered by the same search, or pick a family. Each family keeps its fit reason.
Injectors, ignition and throttle within the ECU2's outputs.
Direct injection needs the DI driver, and DI control is on the roadmap. Advisor mode reads your current ECU's logs meanwhile.
Concept specification. Each row carries its status; nothing here is validated hardware yet.
You choose functions in the app; it assigns them to pins the hardware supports and prints the loom chart.
| Pins | Default | Also usable as |
|---|---|---|
| A1–A8 | Injectors 1–8: low-side, peak-and-hold | Spare = 2 A output or 0–12 V input |
| A9, A12, A14–A17 | DPO 1–6: protected low-side 3 A | Pull-up 5 V / 12 V / off per output |
| A10, A11 | Battery ground (both) | — |
| A13 | Ignition switch input | — |
| A18, A25 | +12 V switched power in (both) | — |
| A19–A22 | Half-bridges 1–4: ~3 A continuous / 10 A peak | Any pair can run a DBW throttle (up to 2) |
| A23, A24 | CAN 1 H / L | — |
| A26 | Main relay output | — |
| A27–A34 | Ignition 1–8: 5 V logic-level coil drive | — |
| Pins | Default | Also usable as |
|---|---|---|
| C1, C2 | Crank +/− (VR or Hall) | — |
| C3, C4 | Cam +/− | — |
| C5–C8, C19, C20 | Synchronised inputs 1–6 | Cam phasers, wheel speed, flex |
| C9 | +8 V sensor supply | — |
| C10–C18, C27, C28 | Analog inputs 1–11: 0–5 V, switchable pull-up | — |
| C21, C22 | CAN 2 H / L | — |
| C23, C24 | Knock 1 + 2 | — |
| C25 | +5 V sensor supply | — |
| C26 | Sensor ground | — |
| C29–C34 | Onboard wideband (Bosch LSU 4.9) | — |
Pin functions follow the published Haltech Nexus S3 wiring diagram so S3 harnesses fit. Physical keying and harness fit are to be verified with real harnesses before release.
Dash, keypad, autotune and Ask GAINS on a phone or a dash-mounted iPad. The engine never depends on it.
See the app →Pick your car or engine to see which GAINS modules fit, how they wire in and what you keep.
Open the planner →Which GAINS products each platform needs, from one ECU2 to a full direct-injection V8 with PDM2.
See the matrix →Launch Edition
Nothing. A reservation is a place in the queue for the Launch Edition. We email you before orders open, and you decide then.
Reservations are served in the order they were made. The first 100 units are the Launch Edition at Est. $899; after that the ECU2 is an estimated $1,099.
The design is still being finished. We confirm the final price to everyone in the queue before orders open, and you can walk away then.
Est. April 2027 is the target. Reservation holders hear first if that moves.
ECU2 · Launch Edition Est. $899
Reserve at Est. $899Coming soon. Specifications and images are pre-release and may change before launch. Pinout compatibility refers to published harness documentation. GAINS is not affiliated with Haltech, Bosch or any other brand named here.