Honda B-series · 1992-01

B20B specs: horsepower, injectors and sensors

The B18B / B20B (non-VTEC) is a naturally aspirated 1.8 L inline-4 engine from Honda (1992-01) with port fuel injection and distributor ignition. The factory ECU measures load by MAP speed-density. Below: factory specification and ratings, sensor part numbers, OEM injectors and direct-fit upgrades, triggers, swaps and tuning notes, each with its evidence.Low1523411810 Conflict

Power: 140 hp @ 6,300 rpm · Torque: 126.9 lb-ft (172 Nm) @ 5,200 rpm (Honda rating, not a GAINS measurement)Low15

Factory specification

Layout, dimensions and factory hardware, each with its source.

Production years1992-01Catalog range across the variants on this page.Researched, unverified
Displacement1.8L1,834 cc from bore × strokeConflict15
Layoutinline-4Researched, unverified
Bore × stroke81 × 89mm3.19 × 3.50 inConflict15
Compression ratio9.2:1Conflict15
Redline6,800rpmConflict15
Aspirationnaturally aspiratedResearched, unverified
Fuel injectionport fuel injectionLow confidence11810
Blockaluminiumhigh-pressure die-castConflict15
Cylinder linerscast-in iron linerssiameseConflict15
Connecting rods~137mm rodsWikipediaConflict15

Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.

B20B horsepower and torque

Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.

Power (Honda rating)140hp @ 6,300 rpmPrimary = B18B1 (US Integra LS/RS/GS) per Wikipedia; rev limit 7300; CR 9.2 US / 9.4 JDMConflict15
Torque (Honda rating)126.9 lb-ft @ 5,200 rpm172 NmConflict15
Other published ratings

B20B (1999-2001 CR-V): 148-150 hp (152 PS) @6200, 190 Nm @5500, 84 x 89 mm, CR 9.4-9.6, redline 6800

Conflict15

B20B firing order

B20B injectors

The factory injector, then direct-fit upgrades the makers list for this engine.

Factory injector

StyleHonda top-feedKeihin/Denso family; maker not confirmedLow confidence11810
OEM part numbers

06164-P2J-000 (listing: Civic 1.6, Integra 1.8, CR-V 2.0, CL 2.3)

Low confidence11810
ImpedancehighsaturatedLow confidence11810
Connector
  • EV1 / Jetronic-typeOBD1
  • Honda OBD2
Low confidence11810
LengthstandardLow confidence11810
FeedtopLow confidence11810
O-ring OD (top / bottom)11/ 14 mmLow confidence11810

Direct-fit upgrades

Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.

InjectorFlowFit
DeatschWerks DW 440cc matched set · 18U-04-0450-417440 cc/min maker rating (basis not stated on page)Needs adapter USCAR-to-OEM plug adapter (DW page states USCAR connector; adapter inclusion not stated)
DeatschWerks DW 1200cc matched set · 16MX-01-1200-4181200 cc/min maker rating (basis not stated on page)Needs adapter USCAR-to-OEM plug adapter (DW page states USCAR connector; adapter inclusion not stated)
Fuel Injector Clinic FIC 445cc High-Z set · is115-0445h20445 cc/min at 43.5 psi (3 bar), CF-16B fluid 90 F (maker)Needs adapter USCAR-to-Jetronic (Honda OBD1) plug adapters PADPUtoJ4 (optional) or solder-in pigtails PGTUSC4 (included); OBD2 harness: PADPUtoH4
Fuel Injector Clinic FIC 1000cc High-Z set · is115-1000h191000 cc/min at 43.5 psi (3 bar), CF-16B fluid 90 F (maker)Needs adapter USCAR-to-Jetronic (Honda OBD1) plug adapters PADPUtoJ4 (optional) or solder-in pigtails PGTUSC4 (included); OBD2 harness: PADPUtoH4
Injector Dynamics ID1050-XDS · 1050.60.11.14.46812141065 cc/min at 3.0 bar, gasoline 52 C (maker)Needs adapter USCAR-to-Honda OBD1 Jetronic or OBD2 plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238)
Injector Dynamics ID1300-XDS · 1300.60.11.14.47913151335 cc/min at 3.0 bar, iso-octane 52 C (maker)Needs adapter USCAR-to-Honda OBD1 Jetronic or OBD2 plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238)

Sensors

Factory sensors by role: part numbers, signal type and fitment years.

SensorOEM part numbersType / signalYears and markets
KnockNot yet sourcedSourced · medium16not listed for non-GS-R Integra (B18B1) in OEM catalogueUS Integra LS/RS/GS 1994-2001Catalogue lists 30530-PV1-A01 only for GS-R/Type R; absence for B18B1 inferred from fitment table.
MAPHonda 37830-PAA-S00 (replaces 37830-P0G-S00)Sourced16MAP sensor ('Sensor Set, MAP')US Integra 1995-2001 LS/RS/GSB20B (CR-V) not checked.
MAFNot yet sourcedSourced · medium16none listed in OEM catalogue (speed-density, MAP-based)
O2 (upstream)Honda 36531-P73-G01 (replaces 36531-P72-A02)Sourced16narrowband zirconia oxygen sensorUS Integra 1996-2001 LS/RS/GSB20B CR-V not checked.
O2 (downstream)Honda 36532-P73-A01 | Honda 36532-P2R-A01Sourced · medium16oxygen sensor (rear)US 1998 Integra

Ignition and triggers

Ignition systemdistributorResearched, unverified
Valve timingnoneResearched, unverified

Tuning notes

Factory load sensing

The factory ECU measures load by MAP speed-density. Same PGM-FI MAP strategy; OBD-II (1996+) US adds downstream sensor. LS-VTEC hybrids inherit whatever ECU is fitted (not an OEM config).Medium23415 Conflict

Factory oxygen sensors

Upstream: narrowband (zirconia), heated on later PGM-FI; no wideband on this family per sources consulted (1). Downstream O2 sensors: varies. Closed-loop fuelling: narrowband closed loop at idle/cruise, open loop cold start and WOT/high load.Medium23415 Conflict

Injector drive

Factory injector impedance: high (saturated). Connector: EV1 / Jetronic-type (OBD1); Honda OBD2.Low11810

Driver and calibration

High-impedance injectors run from a saturated driver. Any injector change needs new flow and dead-time data in the calibration. Researched, unverified

Valvetrain, factory engine management and weak points across every generation are on the Honda B-series guide.

Vehicles with the B18B / B20B (non-VTEC)

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

20 sources
  1. Factory ratings: Honda B-series (E-716) · en.wikipedia.org · reference · retrieved 2026-10-25
  2. Honda PGM-FI load strategy (E-820) · ej9.ru · community · retrieved 2026-10-25
  3. Honda PGM-FI closed loop (E-821) · ej9.ru · community · retrieved 2026-10-25
  4. Honda speed-density + O2 feedback (E-822) · automotivetechinfo.com · reference · retrieved 2026-10-25
  5. Honda B-series internals (E-1030) · en.wikipedia.org · reference · retrieved 2026-10-25
  6. Injector aftermarket fitment (E-1200) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  7. Injector aftermarket fitment (E-1201) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  8. Injectors / ID1050-XDS fitment (E-1230) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  9. Injectors / ID1300-XDS fitment (E-1231) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  10. Injectors / FIC Honda sets (E-1234) · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
  11. Injectors / Honda OEM PNs (B/D/H) (E-1239) · hondapartsnow.com · vendor-doc · retrieved 2026-10-25
  12. Injector Dynamics ID1050-XDS fitment table (E-1260) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  13. Injector Dynamics ID1300/ID1750/ID2600 fitment tables (E-1261) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  14. Injector Dynamics ID1050-XDS fitment table (E-1290) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  15. Injector Dynamics ID1300-XDS fitment table (E-1291) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  16. OEM sensor PNs (Acura Integra) (E-1352) · acurapartswarehouse.com · reference · retrieved 2026-10-25
  17. deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
  18. deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
  19. fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
  20. fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25

Evidence ids (E-…) refer to our research register; each records the source, date and confidence.