Engine load

loadcalculated load valueabsolute load valuerelative loadcylinder fillingload axis

Engine load is a measure of how much air the engine is drawing into its cylinders relative to its capacity, used by the ECU as the main axis for fuel, ignition and other tables. It can be expressed as manifold pressure, throttle angle, air mass per cylinder or a percentage of maximum cylinder filling.123

How it works

Torque depends mainly on how much air, and so fuel, each cylinder burns per cycle.

Load variables are proxies for that cylinder charge. Speed-density systems use manifold absolute pressure, mass-airflow systems use air mass per stroke, and alpha-N systems use throttle angle.31

OBD-II defines two standardized load values. PID 04, calculated load value, is current airflow divided by peak airflow at the current rpm, so wide-open throttle reads near 100% at any speed. PID 43, absolute load value, normalizes air mass per intake stroke to the engine's displacement and can exceed 100% on boosted engines.24

Relative cylinder charge relates to volumetric efficiency. An engine at 100% relative load fills its cylinders with roughly the air mass that the swept volume would hold at standard conditions. Boost or strong tuning effects push it higher.Medium53

In tuning

Choose the load axis to match the strategy.

Manifold pressure works well for speed-density fueling. Air mass per cylinder suits model-based ignition and boost tables because it accounts for temperature and altitude. Throttle angle helps on engines with individual throttle bodies, where manifold pressure barely changes.Medium16

When comparing logs between cars or tools, check which load definition each one reports. A calculated load of 100% at wide-open throttle says nothing about how much air the engine moves, while an absolute load value does.24

Formula and worked example

LOAD_abs (%) = 100 × m_air,stroke / (ρ_std × V_cyl)
LOAD_abs
absolute load value%
m_air,stroke
air mass per cylinder per intake strokeg
ρ_std
air density at standard temperature and pressure, about 1.184 g/L at 25 °C and 101.3 kPag/L
V_cyl
displacement of one cylinderL
Medium27

Try it

cu in
rpm
%
psi

14.7 psia at sea level wide-open throttle without boost.

°F

Result

Volumetric airflow541 CFM at manifold conditions
Mass airflow39.0 lb/min

Planning estimate from the formula below, not a measurement.

Open the full engine airflow (cfm) calculator →

Myths vs facts

Myth 100% load means the engine is making maximum power.

Fact Calculated load reads near 100% at wide-open throttle at any rpm, including low rpm where power is small. It shows throttle opening relative to available airflow, not output.24

Myth Load cannot exceed 100%.

Fact Absolute load and relative charge can exceed 100% when boost or strong intake tuning fills cylinders beyond their swept volume at standard conditions.25

Frequently asked

What does calculated load value mean on OBD2?

It is PID 04 in SAE J1979: current airflow as a percentage of the peak airflow possible at the current engine speed. It reads near 100% at wide-open throttle at any rpm and low at idle. It is useful for comparing throttle demand but not for comparing engine output between speeds.24

What is the difference between calculated load and absolute load?

Calculated load compares current airflow with the maximum at that rpm. Absolute load compares air mass per intake stroke with what the cylinder would hold at standard conditions, so it tracks cylinder filling and torque more closely. Absolute load can exceed 100% on boosted engines.24

Why can engine load exceed 100 percent?

When load is defined as air mass relative to swept volume at standard conditions, a turbocharger, supercharger or strong intake tuning can pack in more air than that. Boosted engines commonly show absolute or relative load well above 100% at full throttle.52

Should I use MAP or load on my fuel table?

It depends on the ECU strategy. Speed-density fueling uses manifold pressure because the VE model needs it. Calculated air mass or load suits ignition and boost tables because it already accounts for temperature and altitude. Individual throttle bodies often need throttle angle instead of manifold pressure at low load.Medium16

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. OBD-II PIDs · Wikipedia · reference · retrieved 2026-10-27
  3. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  4. SAE J1979: E/E Diagnostic Test Modes · SAE International · standard · retrieved 2026-10-27
  5. Volumetric efficiency · Wikipedia · reference · retrieved 2026-10-27
  6. MAP sensor · Wikipedia · reference · retrieved 2026-10-27
  7. Density of air · Wikipedia · reference · retrieved 2026-10-27