Manifold absolute pressure (MAP)

MAPMAP sensormanifold pressureboost pressure sensorT-MAP

Manifold absolute pressure (MAP) is the pressure inside the intake manifold measured relative to a perfect vacuum. A MAP sensor reports it to the ECU, which uses it with air temperature to estimate air density and engine load for fueling and ignition.12

How it works

Manifold absolute pressure never reads below zero, because it is referenced to a perfect vacuum.

At sea level with the engine off, MAP equals barometric pressure of about 101.3 kPa (14.7 psi). Closing the throttle at idle drops MAP well below that, and boost raises it above.1

A boost gauge reads gauge pressure, which is relative to the atmosphere. To convert, add barometric pressure: 100 kPa (14.5 psi) of boost at sea level is about 201 kPa absolute. At altitude the same gauge reading is a lower absolute pressure because the baseline is lower.1

Most automotive MAP sensors are piezoresistive silicon devices that output a voltage proportional to absolute pressure. Their full-scale range sets the highest pressure they can read, so a sensor sized for a naturally aspirated engine will clip under boost.Medium31

Some OEM systems with a MAF sensor still fit a MAP sensor. GM, for example, uses it for rationality checks and EGR testing: opening the EGR valve during deceleration should raise MAP if exhaust gas is flowing.Medium1

In tuning

MAP is the load axis of a speed-density fuel table and often of the ignition table too.

Its resolution matters: a sensor that spans 0 to 400 kPa spreads the same voltage over four times the range of a 0 to 100 kPa unit, so small vacuum changes at idle are harder to see.Medium23

Pick a sensor whose range just covers the highest absolute pressure you expect, with margin, and set the ECU's calibration to match the sensor's published slope and offset. Plumb it to a stable point in the plenum, not a runner where pulses distort the reading.Medium31

Formula and worked example

MAP = P_gauge + P_baro
MAP
manifold absolute pressurekPa
P_gauge
boost (positive) or vacuum (negative) gauge readingkPa
P_baro
barometric pressure, 101.325 at standard sea levelkPa
1

Try it

hp
cu in
rpm
%
:1
:1

Typical: gasoline NA 0.45-0.50, gasoline boosted 0.55-0.65, E85 NA 0.65-0.75, E85 boosted 0.80-0.90 lb/hp-hr.

°F
ft
psi
psi

Result

Airflow required44.0 lb/min
Boost (gauge)25.1 psi
Manifold absolute pressure39.8 psi
Compressor pressure ratio3.05 :1

Planning estimate from the formula below, not a measurement.

Open the full boost for horsepower calculator →

Myths vs facts

Myth A MAP sensor reads boost the same way a boost gauge does.

Fact A MAP sensor reads absolute pressure, so it shows about 100 kPa more than a gauge at sea level and never reads negative. The ECU subtracts barometric pressure if it needs gauge boost.1

Myth A higher-range MAP sensor is always better.

Fact A wider range spreads the same output voltage over more pressure, which lowers resolution at idle and light load. Choose the smallest range that covers peak boost with margin.Medium31

Myth MAP and boost are the same at any altitude.

Fact Gauge boost is relative to local atmospheric pressure, which falls with altitude, so the same boost reading gives a lower absolute manifold pressure and less air mass at elevation.12

Frequently asked

What should a MAP sensor read at idle?

A healthy naturally aspirated engine at sea level typically idles at roughly 30 to 45 kPa absolute, though large cams and altitude raise that figure. The key check is that it reads barometric pressure, about 101 kPa at sea level, with the key on and engine off.Medium12

How do I convert boost psi to kPa absolute?

Multiply the gauge reading in psi by 6.895 to get kPa, then add the local barometric pressure. At sea level, 14.5 psi of boost is 100 kPa gauge, plus 101.3 kPa barometric, giving about 201 kPa absolute. Use your local barometric reading at altitude.1

What MAP sensor do I need for my boost level?

Add your peak boost to barometric pressure and choose a sensor rated above that total. Roughly, a 2-bar sensor (about 200 kPa) suits up to about 14 psi at sea level and a 3-bar sensor (about 300 kPa) suits up to about 29 psi. Leave margin for boost spikes.Medium13

What is a T-MAP sensor?

A T-MAP combines a manifold pressure sensor and an air temperature sensor in one housing. That gives a speed-density ECU both inputs for air density from a single mounting point, which also keeps the temperature reading close to where pressure is measured.Medium31

Can a bad MAP sensor cause rich running?

Yes. If a speed-density ECU sees higher pressure than is really present, from a faulty sensor or a leaking or blocked vacuum line, it calculates more air and adds fuel. Compare key-on, engine-off MAP with known barometric pressure as a first check.Medium12

Wiring, pinouts and parts

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. MAP sensor · Wikipedia · reference · retrieved 2026-10-25
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-25
  3. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-25