Sensor type · Analog 0-5 V (ratiometric)

Barometric (ambient) pressure sensor

baro sensorbarometric pressure sensorambient pressure sensorBAROair box pressure sensor

A barometric (baro) sensor measures ambient absolute pressure so the ECU can correct fuel, boost and timing for altitude and weather. It wires like a MAP sensor: 5 V reference, ground and a ratiometric 0-5 V signal, but its port sees still ambient or air box pressure instead of the manifold. A 1-bar class sensor, such as Bosch's 0.1-1.15 bar PS-AA, gives the best resolution.21

Parts in the library

Support across ECUs

Across the 2 parts in this hub (2 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU22 configurable (generic input)
Haltech (Elite / Nexus)2 configurable (generic input)
Link (G4X)2 configurable (generic input)
MoTeC (M1)2 configurable (generic input)
ECUMaster (EMU Black)2 configurable (generic input)
AEM (Infinity)2 configurable (generic input)
MaxxECU2 configurable (generic input)
Holley (Terminator X / EFI)2 unverified

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

Inside is a piezoresistive element with an integrated circuit for amplification and temperature compensation. Bosch's PS-AA works this way and gives an analog ratiometric output.2

Baro sets the reference for everything pressure-based: speed-density airflow, boost targets in gauge terms and altitude corrections. Air density falls with altitude, so the same manifold pressure fills the cylinder with less air at a given throttle.Medium1

Without a dedicated sensor, many systems read the MAP sensor with the engine stopped, when manifold pressure equals ambient, and hold that value. A separate baro sensor keeps tracking while driving, which matters for hill climbs and long altitude changes.Medium1

Types and variants

1-bar class (0.1-1.15 bar)Analog 0-5 V (ratiometric)

Bosch PS-AA 0 261 230 216: 4,048 mV per bar at 5 V, the finest resolution for ambient pressure.2

2.5-bar air box sensorAnalog 0-5 V (ratiometric)

Bosch PS-AA 0 261 230 284 (0.2-2.5 bar) reads ram-air box pressure above atmosphere, at 1,848 mV per bar.2

12 V-supplied analog (PSA-N)

Bosch's PSA-N (0.1-1.15 bar absolute) runs on 11-16 V with a 0.5-4.7 V analog output, so it needs a 12 V feed rather than the 5 V sensor reference.4

Wiring

Three wires: 5 V reference, sensor ground and signal to an analog input with the pull-up off. Bosch's PS-AA pinout is pin 1 supply, pin 2 ground, pin 3 signal, and Bosch recommends a 2 ms RC filter at the ECU input.2

Mount it in a dry place where the port sees still ambient air, facing down within ±60° of vertical so condensate drains. Behind the grille or in a ram-air box it reads air box pressure instead, which is what Bosch designs the PS-AA family for.Medium2

Connector and wiring library

Common faults and checks

Baro reads far from local weather pressure with the key on

Likely cause Wrong transfer function or a sensor plumbed to the manifold

Check Compare against a local station-pressure report (not sea-level corrected) and check the port is open to ambient.Medium1

Baro wanders with road speed

Likely cause Port in a ram-air or low-pressure zone

Check Move the sensor or its vent to still air inside the cabin or engine bay.Low2

Noisy baro trace

Likely cause No input filter

Check Add Bosch's recommended 2 ms RC low-pass filter at the ECU input.2

Frequently asked

Do I need a separate baro sensor if I have a MAP sensor?

Not always. Many ECUs take baro from the MAP sensor at key-on, before the engine starts. A separate sensor helps when altitude changes during a drive or session, since the key-on value then goes stale.Medium1

What range baro sensor do I need?

A 1-bar class absolute sensor. Ambient pressure sits roughly between 0.7 and 1.05 bar from high altitude to sea level, and Bosch's 0.1-1.15 bar PS-AA covers that with 4,048 mV per bar.Medium21

Can I use a 3-bar MAP sensor as a baro sensor?

It works, but with less resolution. Bosch's 3-bar PS-AS gives 1,518 mV per bar against 4,048 mV per bar for the 1.15-bar PS-AA, so the same ADC sees roughly a third of the voltage change per millibar.32

Where should a baro sensor be mounted?

In a dry spot where its port sees still air, facing down so condensate drains. Avoid the path of ram air or a low-pressure zone under the bonnet, which shift the reading with road speed.Medium21

Related

Use it with GAINS

Barometric (ambient) pressure sensor on GAINS hardware

ECU2Internal 4-bar MAP, sampled at key-on

Pins
On the ECU2 pin map
Pull-up
Not used
Shielding
Not needed

No separate baro sensor in the concept: baro is read from the internal MAP before cranking; firmware may update it at idle or WOT.Medium5

ECU2AVI (0-5 V, pull-up off)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

A dedicated external baro sensor can go on any free AVI with the pull-up off.Medium5

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.56

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-11-04
  2. Pressure Sensor Air PS-AA data sheet 52308363 (27 Jan 2026) · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-11-04
  3. Pressure Sensor Air PS-AS data sheet 52373387 (27 Jan 2026) · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-11-04
  4. Pressure Sensor Air PSA-N data sheet 321117963 (27 Jan 2026) · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-11-04
  5. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  6. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)