Direct injection

GAINS DI

Direct injection. Any ECU.

A direct-injection driver for up to 8 cylinders and 2 high-pressure pumps on one 34-pin connector. Your ECU keeps all injection timing and rail-pressure control; the DI turns its pulses into high-voltage GDI current profiles.

Coming soon

Illustrative model: the shared GAINS envelope with a battery-feed stud. The DI housing is not defined yet. Drag to turn it.
Drives up to8GDI injectors, in 4 banks of 2
Plus2high-pressure pump valves
A65 Vboost supply for fast opening
One sealed34pin connector
How it works

A power stage,
not a second ECU.

Pair it with ECU2 or another ECU. It only shapes the current.

Host keeps control

The ECU decides when and how long each injector and pump valve fires. The DI runs a boost phase to open the injector fast, then a regulated hold.

Two NXP PT2001 drivers

Each automotive solenoid controller runs two injector banks and one pump channel with its own current measurement. A 4-cylinder build fits just one.

Works with any ECU

Each trigger input accepts an ordinary port-injector output.

Independent safe state

Drivers stay inhibited unless both the supervisor and the hardware enable agree. Boost and outputs shut off on a wrong loom, stuck trigger, boost overvoltage or watchdog fault.

Injector profiles over CAN

Current profiles per injector family load from the app through the ECU, with live peak and hold current and fault reporting.

Same family

Same connector family, mounting studs and CAN as ECU2 and PDM2, so a DI car is matching boxes on one bus.

Wiring

How it
connects.

No adapter box. The engine loom carries both Superseal 34 plugs, and a short bridge branch joins them.

ECU → DI

ECU injector outputs go to DI trigger inputs instead of to the injectors; one spare ECU output drives the pump trigger. CAN is shared.

DI → engine

The DI drives the GDI injectors (bank high sides and per-cylinder low sides) and the pump valve. Rail-pressure sensors stay on the ECU.

Power + enable

Fused battery feed to the M6 stud for the boost supply; switched 12 V on the enable pin. Without enable, the boost and all outputs stay off.

Applications

What it
can run.

Direct-injection engines the DI can drive alongside a GAINS host ECU, from published engine specifications.

38DI engines it can drive
37vehicles in the planner
1with a plug-and-play route via ECU2
  • Pre-release: GAINS hardware is concept design with target specifications.
  • Fitment is derived from published pinouts, harness makers' published fitment and engine specifications.
  • Not yet fit-tested or validated on any vehicle.
  • Check your exact car in the planner before you buy anything.

Is my car covered?

One answer per car, straight from the planner's rules: what the DI needs to run it.

Try

264 cars in the planner · popular picks below

Popular 12

2014-19LT1 (Gen V)

Chevrolet Corvette C7 Stingray / Grand Sport

DI + ECU2Roadmap

Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.

Wire-inECU2 →

2014-18L83 5.3 / L86 6.2 (Gen V truck)

Chevrolet / GMC Silverado / Sierra K2XX 5.3 / 6.2 (L83 / L86)

DI + ECU2Roadmap

Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.

Wire-inECU2 →

2018-23Coyote Gen 3

Ford Mustang S550 GT (Coyote Gen 3)

DI + ECU2Roadmap

Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.

Wire-inECU2 →

2011-3.5 EcoBoost V6

Ford F-150 13th / 14th gen 3.5 EcoBoost

DI + ECU2Roadmap

Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.

Wire-inECU2 →

2017-K20C1 2.0T (Type R FK8 / FL5)

Honda Civic Type R FK8 / FL5 K20C1

DI + ECU2Roadmap

Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.

Wire-inECU2 →

2023-K20C1 2.0T (Type R FK8 / FL5)

Acura Integra Type S DE5 K20C1

DI + ECU2Roadmap

Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.

Wire-inECU2 →

2012-20FA20 / FA24 D-4S (86 / BRZ / GR86)

Toyota / Subaru 86 / BRZ / GT86 ZN6 / ZC6 FA20 D-4S

DI + ECU2Roadmap

Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.

Adapter harness (ECU2)ECU2 →

2015-FA20DIT / FA24DIT (WRX)

Subaru WRX VA / VB FA20DIT / FA24DIT

DI + ECU2Roadmap

Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.

Wire-inECU2 →

2006-14EA888 Gen 1-2 (2.0 TSI)

Volkswagen Golf GTI Mk5 / Mk6 EA888 Gen 1-2 / EA113

DI + ECU2Roadmap

Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.

Wire-inECU2 →

2013-20EA888 Gen 3 (Golf GTI / R Mk7, S3 8V)

Volkswagen / Audi Golf GTI / R, Audi S3 Mk7 / 8V EA888 Gen 3

DI + ECU2Roadmap

Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.

Wire-inECU2 →
All 264 vehicles, by make

Alfa Romeo 2

Ariel 1

Bike engines 4

BMW 16

Chevrolet / GM 29

Dodge / Ram / Jeep 6

Fiat 1

Ford 35

Holden / HSV 11

Honda / Acura 31

Hyundai 3

IKA 1

Kit cars 2

Lancia 1

Lotus 3

Mazda 8

Mercedes-Benz 3

MINI 2

Mitsubishi 9

Nissan 19

Peugeot / Citroën 4

Porsche 6

Renault 2

Rover / MG 1

Saab 1

SEAT 2

Skoda 2

Subaru 9

Toyota / Lexus 22

UTV / powersports 3

Vauxhall / Opel 4

Volkswagen / Audi 19

Volvo 2

Engines

Filtered by the same search, or pick a family. Each family keeps its fit reason.

Drives the DI injectors (roadmap)

38 engines

Fits the 8 GDI channels and 2 pump drivers; the host ECU keeps injection timing and rail pressure. DI control is planned, not shipping.

Alfa Romeo · Alfa Romeo 1750 TBi4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Audi · Audi 3.0 TFSI supercharged V66 cyl DI: 6 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Audi · Audi 4.2 V8 FSI8 cyl DI: 8 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Audi · Audi EA855 2.5 TFSI5 cyl DI: 5 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
BMW · BMW B586 cyl DI: 6 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
BMW · BMW N20 2.0 turbo4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Show 20 more engine families
BMW · BMW N546 cyl DI: 6 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
BMW · BMW N63 / S63 twin-turbo V88 cyl DI: 8 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
BMW · BMW S556 cyl DI: 6 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Ford · Ford Coyote8 cyl DI: 8 of 8 GDI channels; the ECU2 host keeps timing and rail pressure, and drives the port injectors (port / DI split is planned). Roadmap.Host: ECU2 →
Ford · Ford EcoBoost2.3 EcoBoost, 2.0 EcoBoost, 1.6 EcoBoost: 4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.3.5 EcoBoost V6: 6 cyl DI: 6 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
GM · GM Ecotec4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
GM · GM LT (Gen V)8 cyl DI: 8 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Honda · Honda K-series4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Honda · Honda L-series4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Mazda · Mazda MZR4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Mazda · Mazda SkyActiv-G4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Mercedes · Mercedes M271 / M274 four4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Mercedes · Mercedes M276 V66 cyl DI: 6 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Mercedes · Mercedes-AMG M113 / M1568 cyl DI: 8 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Porsche · Porsche 9A1 flat-six6 cyl DI: 6 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
PSA/BMW · PSA / BMW Prince (EP6)4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
Toyota · Toyota G16E-GTS3 cyl DI: 3 of 8 GDI channels; the ECU2 host keeps timing and rail pressure, and drives the port injectors (port / DI split is planned). Roadmap.Host: ECU2 →
Toyota/Subaru · Subaru FAFA20 / FA24 D-4S: 4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure, and drives the port injectors (port / DI split is planned). Roadmap.FA20DIT / FA24DIT: 4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
VW · VW/Audi EA113 2.0 TFSI4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.Host: ECU2 →
VW/Audi · VW / Audi EA888EA888 Gen 1-2: 4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure. Roadmap.EA888 Gen 3: 4 cyl DI: 4 of 8 GDI channels; the ECU2 host keeps timing and rail pressure, and drives the port injectors (port / DI split is planned). Roadmap.Host: ECU2 →

Beyond the DI

1 engines

More direct injectors than the DI has channels.

Audi · Audi 5.2 V10 FSI10 cyl exceeds 8 GDI channels.Host: ECU2 →
Safety

High voltage,
handled.

Two keys to runThe drivers stay inhibited unless the supervisor and the hardware enable both agree.
Loom checkA loom-ID resistor stops it running on the wrong loom.
Stuck-trigger cutBoost and outputs shut off on a stuck trigger, boost overvoltage or watchdog fault.
Host in chargeInjection timing and rail-pressure control stay on the ECU; the DI never decides when to fire.
Specifications

Every number
is a target.

Concept specification. Each row carries its status; nothing here is validated hardware yet.

Outputs

Injectors
8 × GDI low-sides in 4 banks of 2 (battery + boost high-side per bank); bank partners 360° apart in firing order
Pump valves
2 × high-side + low-side with current measurement
Boost
65 V DC-DC on a shared rail; energy recovery from injector turn-off
Driver IC
NXP MC33PT2001 programmable solenoid controller (×2; ×1 for 4-cylinder)

Inputs, control and power

Triggers
8 injector + 2 pump, compatible with low-side port-injector outputs
Control
Supervisor MCU: loads driver microcode, CAN, monitors boost, battery, enable and loom ID
Power
M6 stud battery feed (boost and injectors), switched 12 V logic feed, 3 power grounds
Housing
Uses the shared GAINS envelope until its own housing is defined
Pinout

Most pins have
more than one job.

You choose functions in the app; it assigns them to pins the hardware supports and prints the loom chart.

Superseal 34, right-angle

PinsDefaultAlso usable as
1–4Injector bank A–D high sides—
5–12Injectors 1–8 low sides—
13–14Pump valve 1 high / low—
15–16Pump valve 2 high / low—
17–24Injector triggers 1–8 (from the ECU)—
25–26Pump triggers 1–2—
27–28CAN-H, CAN-L—
29Enable (switched 12 V)—
30Loom ID—
31Logic +12 V—
32–34Power ground—
StudBattery feed (M6)—

4-cylinder build: banks A/B, injectors 1–4, pump 1, triggers 1–4 and pump trigger 1.

Direct injection.
Any ECU.

DI · Coming soon

Join the waitlist

Coming soon. Specifications and images are pre-release and may change before launch. Direct injection uses high voltage and high-pressure fuel: have it installed by a qualified professional. GAINS is not affiliated with NXP or any other brand named here.