Ford EcoBoost · 2013-18

2.0 EcoBoost specs: horsepower, injectors and sensors

The 2.0 EcoBoost (Focus ST Mk3) is a turbocharged 2.0 L inline-4 engine from Ford (2013-18) with direct injection and coil-on-plug ignition. Below: factory specification and ratings, sensor part numbers, OEM injectors and direct-fit upgrades, triggers, swaps and tuning notes, each with its evidence.Low142

Power: 252 hp @ 5,500 rpm · Torque: 270 lb-ft (366 Nm) @ 2,500 rpm (Ford rating, not a GAINS measurement)Medium14

Factory specification

Layout, dimensions and factory hardware, each with its source.

Production years2013-18Catalog range across the variants on this page.Researched, unverified
Displacement2.0L1,999 cc from bore × strokeSourced · medium14
Layoutinline-4Researched, unverified
Bore × stroke87.5 × 83.1mm3.44 × 3.27 inSourced · medium14
Compression ratio9.3:1Sourced · medium14
AspirationturbochargedResearched, unverified
Fuel injectiondirect injectionLow confidence2
Blockhigh-pressure die-cast aluminium alloySourced · medium14
Cylinder linersthin cast-in sleevesSourced · medium14
Main capsbedplateSourced · medium14
Crankshaftcast iron, 8 counterweights, 47 mm pinsSourced · medium14

Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.

2.0 EcoBoost horsepower and torque

Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.

Power (Ford rating)252hp @ 5,500 rpmSAE net, 2013-18 Focus ST (US); Wikipedia gives torque plateau 2000-4500 rpm, spec tables give 2500Sourced · medium14
Torque (Ford rating)270 lb-ft @ 2,500 rpm366 NmSourced · medium14
Other published ratingsEU: 250 PSWikipedia lists 255 PSSourced · medium14

2.0 EcoBoost firing order

2.0 EcoBoost injectors

The factory injector, then direct-fit upgrades the makers list for this engine.

Factory injector

StyleGDIdirect injection, solenoidLow confidence2
LengthotherDILow confidence2

Direct-fit upgrades

Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.

InjectorFlowFit
Xtreme-DI (XDI) XDI +50% DI injector set (in Focus ST kit with HPFP-35) · XDI-i010-50Low2not stated +50% (maker claim)Plug-in tune + HPFP

Sensors

Factory sensors by role: part numbers, signal type and fitment years.

SensorOEM part numbersType / signalYears and markets
KnockFord 1S7Z-12A699-BBSourced · medium3Not yet sourced2013-18 Focus 2.0 EcoBoost
MAPFord CV2Z-9F479-A (Map sensor) | BV6Z-9F479-ASourced · medium3Not yet sourced2013-18 Focus STAG9Z-9F479-A also listed (wastegate vacuum sensor)
O2 (upstream)Ford BA5Z-9F472-A (upper)Sourced · medium3Not yet sourced2013-18 Focus 2.0 EB
O2 (downstream)Ford CM5Z-9G444-A (rear)Sourced · medium3Not yet sourced2013-18

Ignition and triggers

Ignition systemcoil-on-plugResearched, unverified
Valve timingTi-VCTResearched, unverified

Tuning notes

Factory load sensing

No acceptable source found for production load strategy. Researched, unverified

Known limits (reported)

The cast-in sleeves are thin and not suited to boring.Medium14

Common first upgrades (reported)

Builders most often report upgrading: forged pistons and forged rods (Mountune long block).Medium14

Valvetrain, factory engine management and weak points across every generation are on the Ford EcoBoost guide.

Vehicles with the 2.0 EcoBoost (Focus ST Mk3)

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. EcoBoost 1.6/2.0/2.3 (E-1022) · en.wikipedia.org · reference · retrieved 2026-10-25
  2. DI aftermarket (E-1223) · ffperformance.co · vendor-doc · retrieved 2026-10-25
  3. OEM sensors Ford Focus ST / Fiesta ST (E-1330) · fordpartsgiant.com · vendor-doc · retrieved 2026-10-25
  4. OEM turbo library (EU/US batch) (E-10545) · en.wikipedia.org · reference · retrieved 2026-11-04

Evidence ids (E-…) refer to our research register; each records the source, date and confidence.

Not yet indexed: fewer than 5 sources.