Intercooler (charge-air cooler)

charge air coolerCACaftercoolerair-to-air intercoolerair-to-water intercoolerheat exchanger

An intercooler is a heat exchanger that cools intake air after a turbocharger or supercharger has compressed and heated it. Cooler air is denser, so the engine traps more oxygen per cycle, and lower charge temperature reduces knock tendency. Air-to-air and air-to-water designs are the two main types.12

How it works

Compressing air raises its temperature.

The less efficient the compressor at its operating point, the hotter the outlet air, as Garrett's compressor maps show through efficiency islands. Hot charge air reduces density and moves the engine closer to knock.34

Air-to-air units pass charge air through a core cooled by airflow from vehicle motion. Air-to-water units pass it through a core cooled by liquid, which then sheds heat in a separate radiator. Liquid cores are compact and respond quickly but can heat soak during long runs.Medium1

Every intercooler causes some pressure drop. Garrett describes bar-and-plate cores with fin density and passages designed to maximize heat transfer while controlling pressure drop. Boost measured at the compressor will be higher than at the manifold.2

Effectiveness compares the actual temperature drop with the maximum possible drop to ambient. A high-effectiveness core brings charge air close to ambient temperature, though never below it for an air-to-air unit.Medium51

In tuning

Intake air temperature is a direct input to fueling and ignition.

Logging temperature before and after the core, plus pressure on both sides, shows whether the cooler or its ducting limits the setup.Medium54

When charge temperature rises in sustained runs, ignition and boost tables need temperature-based corrections. A calibration made on a cool first pull can be unsafe on the third pull of a hot day.Medium4

Formula and worked example

ε = (T_in − T_out) / (T_in − T_amb)
ε
intercooler effectiveness
T_in
charge air temperature entering the core°C or °F
T_out
charge air temperature leaving the core°C or °F
T_amb
cooling medium temperature (ambient air for air-to-air)°C or °F
Medium51

Try it

psi
°F
%

Result

Density altitude2,325 ft
Air density (kg/m³)1.1438
Relative to standard (1.225 kg/m³)93.4 %

Planning estimate from the formula below, not a measurement.

Open the full air density and density altitude calculator →

Myths vs facts

Myth A bigger intercooler is always better.

Fact Larger cores add volume and can add pressure drop and lag. The right core balances cooling, pressure drop and packaging.Medium21

Myth An intercooler can cool air below ambient.

Fact An air-to-air unit can only approach ambient temperature. Only an ice or chilled liquid system can go lower.Medium1

Frequently asked

What does an intercooler do?

It removes the heat added when a turbo or supercharger compresses intake air. Cooling the charge increases its density, so each cylinder fills with more air at the same boost pressure. It also lowers the temperature at the start of compression, which reduces knock tendency and allows more stable ignition timing.14

Air-to-air vs air-to-water intercooler: which is better?

Air-to-air coolers are simple, need no pump and work well with steady airflow, but need long ducting and frontal space. Air-to-water coolers are compact with short charge paths and quick response, but add a pump, radiator and coolant, and can heat soak in long sessions. The best choice depends on packaging and use.Medium1

How do you measure intercooler efficiency?

Log charge temperature before and after the core and the ambient temperature. Effectiveness equals the inlet-to-outlet drop divided by the inlet-to-ambient difference. For example, 150 °C in, 45 °C out at 25 °C ambient gives 105 / 125 = 84 percent. Also log pressure drop across the core.Medium51

What is intercooler pressure drop?

Pressure drop is the boost lost as air pushes through the core and its end tanks. Garrett notes that post-intercooler pressure is always lower than pre-intercooler pressure and designs cores and tanks to limit the loss. A large drop means the turbo works harder for the same manifold pressure.2

Does an intercooler add power?

Not by itself. It increases charge density and knock margin, which lets the engine use more air at the same boost or hold timing that would otherwise be pulled. Whether power increases depends on how the engine is calibrated and whether charge temperature was a limit.Medium14

Wiring, pinouts and parts

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Intercooler · Wikipedia · reference · retrieved 2026-10-25
  2. Garrett intercoolers product overview · Garrett Motion · vendor-doc · retrieved 2026-10-25
  3. Turbo Tech 103 (Expert): compressor maps · Garrett Motion · vendor-doc · retrieved 2026-10-25
  4. Internal Combustion Engine Fundamentals, 2nd edition (J. B. Heywood) · McGraw-Hill Education · book · retrieved 2026-10-25
  5. Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-25