RB25DET Swap Nissan 240SX S13 (1989-94): Mounts, Wiring and Legal Guide

An RB25DET swap into an S13 240SX is a long-established swap, and mount kits are sold for the stock crossmember. It takes swap mounts, a rear-drive RB25 oil pan and gearbox, a driveshaft, cooling and intercooler plumbing, and a merged engine harness. The main hurdles are wiring the Skyline engine into a US chassis, front-end packaging of the longer inline six, and emissions legality.Medium678

Difficulty3/5 · ModerateMedium674
  • Bolt-on mount kits exist that use the stock S13 crossmember.
  • The engine harness is not plug-in; the Skyline harness must be merged with the 240SX chassis wiring.
  • RB25 versions differ in ignition, airflow meter and cam timing hardware, so donor details matter.
  • Only a rear-drive RB25 oil pan clears the S-chassis mounts.
  • The engine was never certified for US sale, which makes US emissions approval hard.

At a glance

The key numbers and parts, with the source on each tile.

Recommended engineRB25DETR33 or R34 NEONissan rates the 1998 R34 25GT Turbo at 280 PS (206 kW) at 6,400 rpm and 343 Nm (253 lb-ft) at 3,200 rpm.Sourced1
Budget alternativeRB20DETNissan rates the 1990 Skyline GTS-t Type M at 215 PS (158 kW) and 265 Nm (195 lb-ft).Sourced2
Stock S13 engineKA24DE, 155 hp and 160 lb-ft217 NmSourced · medium5
Engine weight vs stockNot published in sources foundNo OEM weight was found for the RB25DET or KA24DE, so no difference is given.Low confidence4
Mount approach

Swap mounts and crossmember brackets on the stock S13 crossmember

Sourced · medium6
Oil pan
  • Rear-drive RB25DET pan
  • An all-wheel-drive RB26 pan will not clear
Sourced · medium6
Transmission

RB20 or RB25 rear-drive five-speed, with a matching transmission mount

Sourced · medium6
Load sensing
  • Hot-wire mass airflow meter
  • R34 NEO uses one heated oxygen sensor
Sourced3

Recommended engines

  • RB25DET / NEO · The usual choice: a turbo inline six with intake cam timing and a rear-drive five-speed, widely available from R33 and R34 Skylines. Nissan rates the R34 NEO version at 280 PS (206 kW).
  • RB20DET · Lighter on the wallet and simpler to wire, with no variable cam timing. Nissan rates it at 215 PS (158 kW), so it gives up low-end torque to the RB25.
  • RB26DETT · The GT-R engine. Its all-wheel-drive oil pan does not clear S-chassis mounts, and it costs far more, so it suits builds where the engine itself is the goal.

Mounts

Typical kit contents

Left and right engine mounts, transmission mount, two crossmember mounts, transmission brace, hardware

Sourced · medium6
Engine coverageKit engine mounts listed for RB20, RB25 and RB26Sourced · medium6

An RB25 swap into an S13 normally keeps the stock 240SX crossmember and uses brackets that move the mounting points to suit the RB block. Some builders instead fit a Skyline crossmember, which forum users report sits the engine higher.Medium67

Order the transmission mount for the gearbox you actually have, because RB20 and RB25 transmissions mount differently. Swap kits ask you to choose at purchase.Medium6

Transmission

Use the RB gearbox that came with the engine where possible, because it bolts to the block without adapters.

Gearbox optionsRB20 or RB25 rear-drive five-speedSourced · medium6
Stock S13 transmissionsFive-speed manual or four-speed automaticSourced · medium5
Driveshaft yokes

Automatic and manual 240SX driveshafts use different transmission yokes

Low confidence7

The KA24DE transmission does not fit the RB bellhousing pattern, so the stock gearbox stays behind.Medium67

The driveshaft needs a yoke that matches the RB gearbox and a length that matches the new transmission position. A one-piece shaft built to measurement is a common fix; measure after the engine and transmission are mounted.Low7

Clearance

Oil panRear-drive RB25DET pan required for pan clearanceSourced · medium6
Hood

Forum reports range from tight clearance to the factory intake hitting the hood

Low confidence7

The RB is a long inline six in a bay built for a four-cylinder, so the radiator, fans and intercooler pipes fight for space at the front. Check the steering shaft, brake lines and firewall as you lower the engine.Low76

All-wheel-drive RB26 and some RB25 engines from four-wheel-drive models use a different pan that hits the S-chassis mounts. Swap to a rear-drive pan before installation; forum users note four-wheel-drive and rear-drive blocks are not simply interchangeable.Medium67

Cooling

Plan on a radiator and electric fans sized for a turbo six, and leave room for the intercooler in front of it.

NEO thermostat82 C opening temperature180 FSourced · medium4
Intercooler

Front-mount intercooler and piping must be packaged in the S13 bumper

Low confidence4

The S13's stock radiator was sized for the KA24DE and is the first part to replace.Low54

Bleed the system from the highest point and confirm the fans switch on before the coolant reaches the thermostat's opening temperature plus a margin. Add a turbo oil and coolant feed check to the first-start list.Low4

Fuel

The S13's pump was sized for a naturally aspirated KA24DE.

Load sensingHot-wire mass airflow sensorSourced3
Factory closed loop
  • Narrowband oxygen feedback at light load
  • Open loop under load
Sourced · medium3

An RB25 at boost needs more flow, so size the pump for your power target and fuel type with a margin, then confirm pressure under load with a gauge or logging.Low51

Keep the injector, regulator and airflow meter set matched to the calibration you run. Changing any of them changes fueling across the whole map.Medium3

Exhaust

Most swaps run a custom or swap-specific downpipe into a 3 in (76 mm) exhaust.

Turbo outlet

Needs a downpipe routed to suit the S13 tunnel and steering shaft

Low confidence7
Series 2 turboCeramic turbine wheelSourced · medium4

Route it clear of the steering shaft on left-hand-drive cars, which is a known tight spot.Low7

Wikipedia notes the series 2 RB25 turbo uses a ceramic turbine wheel. Treat the factory turbo as a stock-boost part and plan a replacement if you raise boost.Low4

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads
Series 2 changes (1995 on)

Coils with built-in igniters, different airflow meter, new ECU, revised sensors

Sourced · medium4
Cam timing
  • Intake cam timing (NVCS) from 1993
  • On/off solenoid on NEO
Sourced · medium4
Harness
  • Not plug-in
  • Skyline engine harness must be merged with 240SX chassis wiring
Low confidence7

Any RB25 controller needs the cam-driven crank angle sensor signals, six coils with their igniters, six injectors, the airflow meter and air temperature, throttle position, knock sensing and an oxygen sensor. Add the intake cam solenoid and a boost control solenoid.Medium43

On the chassis side, wire ignition and start feeds, fuel pump control, the tachometer, coolant gauge, warning lights, A/C request and fans. Forum users report the speedometer and reverse lights need attention too. Check whether a late donor ECU expects an immobilizer key.Low7

Series 1 and series 2 RB25 harnesses and sensors are not interchangeable, so keep the donor's matching set together. Safety: fuse new feeds at the battery and disconnect it before wiring.Medium4

Chassis

The RB adds weight over the front axle compared with the four-cylinder.

S13 curb weight1,224kg2,698 lbSourced · medium5
Factory LSD
  • Standard on overseas and Canadian models
  • Optional in a US sports package
Sourced · medium5

Recheck ride height and corner weights after the swap and upgrade front springs if the car sits low.Low5

Clutch, axles and differential all see more torque. Open-differential cars usually get a limited-slip unit, and brakes should be sized for the new speed potential.Low51

Tuning

The factory narrowband sensor only tells rich from lean near stoichiometric, so fit a wideband sensor for any tuning under boost.

Compression9.0:1RB25DETSourced · medium4
Factory oxygen sensorSingle heated narrowband sensor on the R34 NEOSourced3

Log lambda, boost, knock and airflow together.Medium3

A larger turbo, a new intake pipe or a different airflow meter all change the load calculation, so recalibrate after each. Keep spark changes conservative and guided by knock data, and raise boost in small steps.Low34

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 24 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Choose the engine
    Decide between RB20, RB25 series 1, series 2 or NEO, and buy the engine with its own harness, gearbox and sensors.
  2. Swap the oil pan
    Fit a rear-drive RB25 pan before installation if the donor came from a four-wheel-drive model.
  3. Strip the S13
    Remove the KA24DE, transmission, driveshaft and engine harness. Label chassis connectors.
  4. Fit mounts
    Install the swap brackets on the stock crossmember and the transmission mount and brace.
  5. Install engine and gearbox
    Lower the RB with a load leveler, check steering shaft, firewall and hood clearance, and torque the mounts.
  6. Driveline
    Adapt the clutch hydraulics, check shifter position, then measure for the driveshaft.
  7. Cooling, intercooler and exhaust
    Fit the radiator, fans, intercooler and pipes, then the downpipe and exhaust.
  8. Fuel
    Install the uprated pump and check pressure and leaks with the key on.
  9. Wiring
    Merge the engine and chassis harnesses, then verify power, grounds, gauges, fans and the pump.
  10. Start and tune
    Prime oil, start, bleed the cooling system, then tune with a wideband on low boost before raising it.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Oil pan hits the crossmember or mountsFour-wheel-drive pan on the engineFit a rear-drive RB25 pan and pickup.Medium6
Speedometer and reverse lights dead after the swapGearbox sensors and switches not wired to the 240SX chassisWire the reverse switch into the chassis circuit and add a speed signal solution for the cluster.Low7
Driveshaft will not fit the gearboxWrong yoke or lengthUse a shaft with the RB gearbox yoke, built to the measured length.Low7
Misfires or no start with mixed partsSeries 1 and series 2 harness, coils or airflow meter mixedKeep one series' harness, coils, airflow meter and sensors together.Medium4
Loss of oil pressure at high rpmOil pump drive collar failure, a known RB issueInspect the pump drive and use an upgraded drive collar before running high rpm.Medium4

Frequently asked

What do I need to RB25 swap an S13?

At minimum: an RB25DET with its matching harness and sensors, a rear-drive RB25 oil pan, swap mounts for the stock crossmember, an RB five-speed with a matching transmission mount, a driveshaft built to fit, an upgraded radiator and intercooler setup, a stronger fuel pump and a merged wiring harness with a suitable engine controller.Medium67

Do I need a Skyline crossmember for an RB swap?

No. Swap mount kits relocate the mounting points so the RB sits on the stock S13 crossmember. Some builders use a Skyline crossmember instead, but forum users report it sits the engine higher, which makes hood clearance harder. The bracket route is the more common one today.Medium67

RB20 or RB25 for an S13?

The RB25 for most builds. Nissan rates the R34 RB25DET NEO at 280 PS and 343 Nm, against 215 PS and 265 Nm for the RB20DET in the R32 GTS-t Type M. The RB20 is cheaper and has no variable cam timing, which simplifies wiring, but it gives up a lot of torque.12

Will an RB26 fit in an S13?

It can, but not with its factory pan. The RB26 came from the all-wheel-drive GT-R, and its oil pan does not clear S-chassis swap mounts, so a rear-drive pan is needed. The engine, its twin turbos and parts cost far more than an RB25, so most S13 builds pick the RB25.Medium64

Is an RB25 swap street legal in the US?

Rarely. The EPA accepts a swap that matches a US-certified configuration of the same or newer model year, and the RB25 was never sold in a US-certified car. The remaining federal route is emissions testing. California inspects engine changes against the donor's rules. This is general information, not legal advice.Medium894

How hard is the RB25 wiring in a 240SX?

It is the hardest part for most people. The Skyline engine harness does not plug into the 240SX, so power, ignition, fuel pump, gauges, fans and A/C must be merged by hand or with a purpose-built harness. Series 1 and series 2 engines also differ in coils, airflow meter and sensors.Medium74

Related

Sources

12 sources
  1. Skyline 25GT Turbo (1998: ER34) · Nissan Heritage Collection · oem · retrieved 2026-10-25
  2. Skyline GTS-t Type M (1990: HCR32) · Nissan Heritage Collection · oem · retrieved 2026-10-25
  3. Nissan Skyline R34 workshop manual (engine control system, RB25DET NEO) · Nissan Motor Co. · service-manual · retrieved 2026-10-25
  4. Nissan RB engine · Wikipedia · reference · retrieved 2026-10-25
  5. Nissan 240SX · Wikipedia · reference · retrieved 2026-10-25
  6. ISR Performance RB Swap Mounts for Nissan 240sx S13/14 · ISR Performance · vendor-doc · retrieved 2026-10-25
  7. What is needed to swap a RB into a 240sx? FAQ · NICOclub Forums · community · retrieved 2026-10-25
  8. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act · U.S. Environmental Protection Agency · standard · retrieved 2026-10-25
  9. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  10. Change vehicle details on a V5C registration certificate (log book) · GOV.UK (DVLA) · standard · retrieved 2026-10-25
  11. § 19 StVZO: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  12. Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government Department of Infrastructure, Transport, Regional Development, Communications and the Arts · standard · retrieved 2026-10-25