Glossary
Engine tuning, defined.
168 terms in plain English, each with how it works, why it matters when tuning, common myths and sources.
A
- A/R ratio (turbine housing) · A/R, turbine A/R, area over radius
A/R ratio is a turbine or compressor housing's volute cross-sectional area divided by the radius from the turbo shaft to that area's centroid.
- Acceleration enrichment (transient fueling and wall wetting) · acceleration enrichment, accel enrichment, transient fuel compensation
Transient fueling, often called acceleration enrichment, is the ECU logic that adds or removes fuel during rapid load changes so the mixture stays on target.
- Accelerator pedal position sensor (APPS) · APPS, APP sensor, pedal position sensor
An accelerator pedal position sensor is the sensor in a drive-by-wire pedal that converts pedal travel into electrical signals for the ECU.
- AFM / DOD delete · AFM delete, DOD delete, AFM disable
An AFM delete is the removal or permanent disabling of GM's Active Fuel Management cylinder deactivation; a DOD delete is the same job named after its earlier Displacement on Demand label, and also used for Chrysler's MDS.
- Air-fuel ratio (AFR) · AFR, A/F ratio, air/fuel ratio
Air-fuel ratio (AFR) is the mass of air divided by the mass of fuel in an engine's combustion mixture.
- Alpha-N (throttle-based load) · alpha-N, α-N, TPS-based load
Alpha-N is an engine-load strategy in which the ECU looks up fuel and ignition from throttle angle (alpha) and engine speed (N), without measuring airflow or manifold pressure.
- Anti-lag · ALS, anti-lag system, bang-bang
Anti-lag is a motorsport strategy that keeps a turbocharger spinning when the driver lifts off the throttle.
- Automotive wire gauge · AWG, wire size, cable cross-section
Automotive wire gauge is the conductor size of a vehicle cable, given in American Wire Gauge (AWG) or square millimeters.
B
- Ball bearing turbo · ball bearing turbocharger, BB turbo, dual ball bearing turbo
A ball bearing turbo is a turbocharger whose shaft runs in a cartridge of angular contact ball bearings instead of oil-film journal bearings and a separate thrust bearing.
- Barometric pressure sensor · baro sensor, BARO, BAP sensor
A baro sensor (barometric pressure sensor) is a sensor that measures ambient air pressure so the ECU can correct for altitude and weather.
- Base map · base tune, start-up map, base calibration
A base map is the starting calibration loaded into an engine computer before it is tuned on the specific vehicle.
- Blow-off valve (BOV / diverter valve) · BOV, diverter valve, bypass valve
A blow-off valve is a pressure-relief valve on the intake side of a turbocharged engine that opens when the throttle snaps shut, releasing trapped boost.
- Blow-through · blow through MAF, blow-through carburetor, blow-through turbo
Blow-through is a forced-induction layout where the turbo or supercharger pushes pressurized air through a metering device, such as a carburetor or MAF sensor, placed after the compressor.
- Boost by gear · gear-based boost, boost per gear, gear dependent boost
Boost by gear is a boost control strategy that sets a different boost target for each transmission gear.
- Boost controller · MBC, manual boost controller, EBC
A boost controller is a device that changes how much boost pressure reaches the wastegate actuator, so the turbo can run above the wastegate spring's base pressure.
- Boost creep · wastegate creep, boost rise at high rpm, uncontrolled boost rise
Boost creep is a steady rise in boost pressure above the wastegate setting as engine speed climbs, because the wastegate cannot bypass enough exhaust flow around the turbine even when fully open.
- Boost gauge · boost/vacuum gauge, vacuum boost gauge, boost pressure gauge
A boost gauge is a pressure gauge that shows intake manifold pressure relative to the atmosphere on a turbocharged or supercharged engine.
- Boost leak · charge air leak, intake leak under boost, boost leak test
A boost leak is any opening in the pressurized intake tract of a turbocharged or supercharged engine, between the compressor and the cylinders, that lets charge air escape.
- Boost solenoid · boost control solenoid valve, wastegate solenoid, boost control valve
A boost solenoid is an electrically switched air valve that controls the pressure signal reaching a turbo's wastegate actuator.
- Boost spike · boost overshoot, overboost spike, transient overboost
Boost spike is a short overshoot of boost pressure above the target as the turbo first comes up to speed, before the wastegate or boost controller brings it back down.
- Brake specific fuel consumption (BSFC) · BSFC, specific fuel consumption, SFC
Brake specific fuel consumption (BSFC) is the fuel mass an engine burns per unit of power it delivers at the crankshaft, per hour.
- Brushless fuel pump · BLDC fuel pump, brushless DC fuel pump, EC fuel pump
A brushless fuel pump is an electric fuel pump driven by a brushless DC (BLDC) motor, with an electronic controller doing the commutation that brushes do in a conventional pump.
C
- Cam sync (cam position signal) · cam position sensor, CMP, cam phase sensor
Cam sync is a signal from a sensor reading the camshaft, used by the engine controller to tell which half of the four-stroke cycle each cylinder is in.
- CAN bus · Controller Area Network, CAN, CAN FD
CAN bus is the Controller Area Network, a two-wire serial network that lets vehicle control units share data.
- CAN bus termination · CAN terminating resistor, 120 ohm termination, CAN termination resistor
CAN bus termination is the pair of resistors, normally 120 Ω each, fitted across CAN high and CAN low at the two physical ends of a high-speed CAN bus.
- CAN ID (arbitration ID) · CAN identifier, arbitration ID, message ID
A CAN ID is the identifier at the start of every CAN frame that names the message and sets its priority on the bus.
- CDI ignition · capacitor discharge ignition, CDI, CD ignition
CDI ignition (capacitor discharge ignition) is an ignition system that charges a capacitor to a few hundred volts and dumps it through the coil primary with a fast switch.
- Centrifugal supercharger · centrifugal blower, belt-driven centrifugal compressor, dynamic supercharger
A centrifugal supercharger is a belt-driven dynamic compressor that spins an impeller at very high speed through a step-up gearbox, flinging air outward and converting its velocity into pressure.
- Chassis dyno (chassis dynamometer) · chassis dynamometer, rolling road, roller dyno
A chassis dyno is a dynamometer that measures a complete vehicle's output at the driven wheels or hubs, with its transmission and driveline in place.
- Closed loop vs open loop fueling · closed loop, open loop, closed-loop fueling
Closed loop and open loop are the two ways an ECU sets fuel.
- Clutch kick · clutch kicking, kicking the clutch, clutch dip
A clutch kick is a drifting technique in which the driver, holding steady throttle, quickly presses and releases the clutch.
- Coil-on-plug ignition · COP, direct ignition, pencil coil
Coil-on-plug ignition is a layout in which every cylinder has its own ignition coil mounted directly on its spark plug, with no distributor or plug leads.
- Compression ratio (static and dynamic) · CR, static compression ratio, dynamic compression ratio
Compression ratio is the ratio of total cylinder volume with the piston at bottom dead center to the volume left at top dead center.
- Compressor choke · choke line, choke flow, stonewall
Compressor choke is the maximum-flow limit of a turbocharger compressor, shown as the choke line on the right-hand edge of the compressor map.
- Compressor surge · turbo surge, surge line, compressor flutter
Compressor surge is an unstable flow condition in a turbocharger compressor where pressure ratio is too high for the mass flow, so air briefly reverses through the wheel.
- Coolant temperature sensor (ECT) · ECT sensor, ECT, CTS
A coolant temperature sensor (ECT sensor) is a thermistor screwed into the engine's water jacket that reports coolant temperature to the ECU.
- Crank trigger wheel (e.g. 36-1, 60-2, 24x/58x) · trigger wheel, reluctor wheel, tone wheel
A crank trigger wheel is a toothed ring fixed to the crankshaft that a position sensor reads to tell the engine controller crank speed and angle.
- Crankshaft position sensor (CKP) · CKP sensor, crank sensor, crank position sensor
A crankshaft position sensor is the sensor that tells the engine computer how fast the crankshaft turns and where it is in its rotation.
- Cylinder deactivation · variable displacement, Active Fuel Management, Dynamic Fuel Management
Cylinder deactivation is an engine strategy that shuts off fuel and holds the valves closed on some cylinders at light load, so the remaining cylinders work harder at higher efficiency.
D
- Data logger · datalogger, data acquisition system, DAQ
A data logger is a device that records measurements over time, each with a timestamp, so they can be reviewed later.
- Data logging · datalogging, data acquisition, DAQ
Data logging is recording engine and vehicle signals over time, such as speed, load, air-fuel ratio, timing, boost and temperatures, for later review.
- DBC file · CAN database, CAN DBC, .dbc
A DBC file is a text database that describes how to decode CAN bus messages into physical values.
- DFCO (deceleration fuel cut-off) · DFCO, DFSO, overrun fuel cut
DFCO, short for deceleration fuel cut-off, is an ECU strategy that stops fuel injection when the throttle is closed and engine speed is above a threshold, such as when coasting in gear.
- Diagnostic trouble code (DTC) · DTC, fault code, trouble code
A diagnostic trouble code is a standardized five-character fault identifier that a vehicle's control modules store when on-board diagnostics detect a problem.
- Digital dash · digital dashboard, dash display, dash logger
A digital dash is a programmable screen that replaces or supplements analog gauges, showing engine and vehicle data on one configurable display.
- Direct injection (GDI) · GDI, DI, gasoline direct injection
Direct injection (GDI) is a fuel-injection method that sprays gasoline at high pressure straight into the combustion chamber rather than into the intake port.
- Drive-by-wire (electronic throttle control) · ETC, electronic throttle, throttle-by-wire
Drive-by-wire is electronic throttle control: the accelerator pedal sends position signals to the engine controller, which drives a motor on the throttle body to open the throttle plate.
- Dyno tuning · dyno tune, dynamometer tuning, dyno calibration
Dyno tuning is calibrating an engine's fuel, ignition and boost tables while the vehicle or engine runs on a dynamometer that measures torque under controlled load.
E
- E85 · E85 fuel, flex fuel, ethanol fuel
E85 is a high-ethanol fuel blend for flex-fuel vehicles that contains 51% to 83% ethanol by volume, with the rest gasoline, depending on season and region.
- eFuse (electronic fuse) · eFuse, e-fuse, electronic circuit breaker
An eFuse is a semiconductor switch that measures its own current and turns off when current exceeds a set limit, protecting the wire and load like a fuse but resetting electronically.
- Electric fan controller · fan controller, radiator fan controller, cooling fan controller
An electric fan controller is the circuit that decides when a radiator cooling fan runs and how fast.
- Electronic boost control · EBC, boost controller, boost control solenoid
Electronic boost control is the engine controller's regulation of turbocharger boost by managing the pressure that reaches the wastegate actuator, usually with a pulsed solenoid valve.
- Electronic wastegate · electric wastegate, electric wastegate actuator, EWG
An electronic wastegate is a turbo wastegate moved by an electric actuator instead of a boost-pressure diaphragm.
- Engine dyno (engine dynamometer) · engine dynamometer, engine dyno cell, brake dynamometer
An engine dyno is a dynamometer that loads an engine on a test stand and measures its torque at the crankshaft or flywheel, without the vehicle's transmission or tires.
- Engine knock (detonation) · detonation, pinging, pinking
Engine knock is abnormal combustion in which pockets of unburned mixture ahead of the flame auto-ignite before the flame reaches them.
- Engine load · load, calculated load value, absolute load value
Engine load is a measure of how much air the engine is drawing into its cylinders relative to its capacity, used by the ECU as the main axis for fuel, ignition and other tables.
- Exhaust back pressure · back pressure, backpressure, exhaust manifold pressure
Exhaust back pressure is the pressure in the exhaust system upstream of a restriction, most importantly in the exhaust manifold ahead of a turbocharger turbine.
- Exhaust gas temperature (EGT) sensor · EGT sensor, EGT probe, pyrometer
An exhaust gas temperature (EGT) sensor is a probe, usually a type K thermocouple, that measures exhaust gas temperature in a runner, collector or turbine inlet.
F
- Flex fuel (E85 and flexible-fuel vehicles) · flex-fuel, FFV, flexible-fuel vehicle
Flex fuel is the common name for E85, a gasoline-ethanol blend containing 51% to 83% ethanol, and for the flexible-fuel vehicles (FFVs) built to run on it.
- Flex fuel kit · E85 flex kit, ethanol conversion kit, flex fuel conversion kit
A flex fuel kit is a set of parts that lets an engine measure its fuel's ethanol content so the ECU can adjust fueling and timing for any gasoline-ethanol blend.
- Flyback diode · freewheeling diode, snubber diode, suppression diode
A flyback diode is a diode placed across an inductive load, such as a relay coil or solenoid, to give its current a path when the switch turns off.
- Freeze frame data · freeze frame, OBD freeze frame, service $02
Freeze frame data is a snapshot of engine operating conditions that an OBD-II engine controller stores when an emissions-related diagnostic trouble code is set.
- Fuel map · fuel table, VE table, base fuel table
A fuel map is the ECU table that sets how much fuel the engine gets at each operating point, usually indexed by engine speed and load.
- Fuel pressure regulator · FPR, rising rate regulator, vacuum-referenced regulator
A fuel pressure regulator is a valve that holds fuel rail pressure at a set value, or at a set value above manifold pressure, by bypassing excess pump flow back to the tank.
- Fuel pressure sensor · FPS, fuel pressure transducer, FRP sensor
A fuel pressure sensor is a transducer that measures fuel pressure in the supply line or rail and sends a voltage to the ECU or logger.
- Fuel pump speed control · PWM fuel pump control, fuel pump PWM, variable speed fuel pump
Fuel pump speed control is varying an electric fuel pump's speed to match fuel demand, usually by pulse-width modulating its supply voltage.
- Fuel rail · injector rail, fuel log, common rail
A fuel rail is the pipe or block that carries pressurized fuel to each injector and holds them in place.
- Fuel return line · return line, fuel return, return-style fuel system
A fuel return line is the low-pressure line that carries fuel the engine does not use from the pressure regulator back to the tank.
- Fuel surge tank · surge tank, swirl pot, fuel swirl pot
A fuel surge tank is a small secondary reservoir that keeps the main fuel pump submerged when fuel sloshes away from the pickup in the main tank.
- Fuel temperature compensation · fuel temp correction, fuel temperature correction, fuel density compensation
Fuel temperature compensation is an ECU correction that adjusts injected fuel as fuel temperature changes.
- Fuel trim (short- and long-term) · STFT, LTFT, short term fuel trim
Fuel trim is the percentage correction an ECU applies to its base fuel calculation using oxygen-sensor feedback.
G
- Ground loop · ground offset, earth loop, ground shift
A ground loop is a condition where two points that should share the same ground potential sit at different voltages, because return current flows through shared resistance or a closed loop picks up induced current.
H
- H-bridge · H bridge, full bridge, H-bridge motor driver
An H-bridge is a circuit of four switches arranged around a load, usually a DC motor, so current can be driven through it in either direction.
- Hall-effect sensor · Hall sensor, Hall effect pickup, digital crank sensor
A Hall-effect sensor is an active semiconductor sensor that switches its output when a magnetic field crosses a threshold.
- Heat soak · heatsoak, intercooler heat soak, IAT heat soak
Heat soak is the buildup of heat in engine components, intake air, intercoolers or fuel when airflow drops or the engine stops.
- High pressure fuel pump (HPFP) · HPFP, GDI pump, direct injection fuel pump
A high pressure fuel pump (HPFP) is an engine-driven piston pump that raises fuel from the low-pressure supply to the pressure a direct-injection rail needs.
- High-side switch · high side driver, high-side output, smart high-side switch
A high-side switch is a switch placed between the positive supply and the load, with the load's other end connected to ground.
I
- Idle air control · IAC, idle air control valve, idle speed control
Idle air control is the engine controller's management of idle speed by metering air around or through the closed throttle.
- Ignition coil · coil, spark coil, coil pack
An ignition coil is a step-up transformer that turns 12 V battery power into the 10,000 to 40,000 V pulse that jumps a spark plug gap.
- Ignition dwell · dwell time, coil charge time, dwell angle
Ignition dwell is the time the ignition coil's primary winding is switched on and charging before the spark.
- Ignition map · ignition table, spark table, timing map
An ignition map is the ECU table that sets base spark advance for each combination of engine speed and load.
- Ignition timing (spark advance) · spark advance, spark timing, timing advance
Ignition timing is the point in the engine cycle, measured in crankshaft degrees before top dead center, at which the spark plug fires.
- Immobilizer · engine immobilizer, immobiliser, transponder immobilizer
An immobilizer is an electronic anti-theft system that stops the engine from running unless an authorized key or code is present.
- Individual cylinder trim · cylinder trim, per-cylinder fuel trim, individual cylinder fuel correction
Individual cylinder trim is an ECU correction that adjusts fuel or ignition timing for one cylinder relative to the others.
- Injector dead time (latency) · dead time, injector latency, injector offset
Injector dead time is the part of a commanded injector pulse during which little or no fuel flows, because the solenoid needle takes time to open and close.
- Injector duty cycle · IDC, duty cycle, injector duty
Injector duty cycle is the percentage of each engine cycle that a fuel injector is held open.
- Injector flow rate · injector size, static flow rate, cc/min
Injector flow rate is the amount of fuel an injector delivers when held fully open at a stated pressure, given in cc/min, lb/hr or g/min.
- Injector impedance · high impedance injector, low impedance injector, saturated injector
Injector impedance is the electrical resistance of a fuel injector's solenoid coil, used to classify injectors as high impedance (roughly 10 to 16 Ω) or low impedance (roughly 1 to 4 Ω).
- Injector phasing · injection timing, end of injection angle, EOI
Injector phasing is the crank angle at which each injection event happens relative to the engine cycle, usually set as the end of injection angle before the intake valve opens or closes.
- Injector short pulse width · short pulse adder, small pulse width correction, injector non-linear region
Injector short pulse width is the range of very short injection pulses, typically the first one or two milliseconds, where fuel delivered no longer scales linearly with pulse length.
- Intake air temperature (IAT) sensor · IAT sensor, IAT, air temperature sensor
An intake air temperature sensor is a thermistor that reports the temperature of the air entering the engine so the ECU can estimate air density.
- Intake air temperature correction · IAT correction, air temperature correction, IAT timing correction
Intake air temperature correction is the set of ECU adjustments that change fueling and ignition timing as intake or charge air temperature changes.
- Intercooler (charge-air cooler) · charge air cooler, CAC, aftercooler
An intercooler is a heat exchanger that cools intake air after a turbocharger or supercharger has compressed and heated it.
K
- Knock sensor · detonation sensor, KS, knock detection sensor
A knock sensor is a vibration sensor bolted to the engine block or cylinder head that converts structure-borne noise into a voltage.
L
- Lambda · λ, lambda value, excess air ratio
Lambda (λ) is the ratio of the actual air-fuel ratio to the stoichiometric air-fuel ratio for the fuel in use.
- Lap timer · GPS lap timer, predictive lap timer, lap timing system
A lap timer is a device that measures how long a vehicle takes to complete each lap of a circuit.
- Launch control · launch control, two-step, 2-step
Launch control is an engine and driveline strategy for repeatable standing starts.
- Lift pump · low-pressure fuel pump, transfer pump, feed pump
A lift pump is the low-pressure pump that moves fuel from the tank to a high-pressure pump, injection pump or surge tank.
- Limp mode · limp home mode, limp-home, failsafe mode
Limp mode is a failsafe strategy in which the engine or transmission computer limits power, speed or gear selection after it detects a fault it cannot safely ignore.
- Load dump · load dump transient, alternator load dump, ISO 16750-2 test A
A load dump is the high-energy voltage surge produced when a charging alternator suddenly loses its load, most often because the battery is disconnected while the engine runs.
- Low-side switch · low side driver, ground-switched output, open-drain output
A low-side switch is a switch placed between a load and ground, with the load's other end permanently connected to positive supply.
- Low-speed pre-ignition (LSPI) · LSPI, stochastic pre-ignition, super-knock
Low-speed pre-ignition (LSPI) is random pre-ignition in downsized turbocharged engines, mostly direct-injected, at low rpm and high load.
M
- Manifold absolute pressure (MAP) · MAP, MAP sensor, manifold pressure
Manifold absolute pressure (MAP) is the pressure inside the intake manifold measured relative to a perfect vacuum.
- MAP vs MAF · MAF vs MAP, speed-density vs mass airflow, MAP vs MAF sensor
MAP vs MAF is the choice between two ways an ECU measures engine airflow.
- Mass airflow (MAF) sensor · MAF, MAF sensor, air mass meter
A mass airflow (MAF) sensor is an intake sensor that measures the mass of air entering the engine, usually by how much a heated wire or film is cooled by the passing air.
- MBT timing (minimum advance for best torque) · MBT, minimum spark advance for best torque, maximum brake torque timing
MBT timing is the smallest spark advance that gives the engine its best torque at a given speed and load.
- Methanol fuel · methanol, M100, alcohol fuel
Methanol fuel is methyl alcohol (CH3OH) burned as an engine fuel, usually neat as M100 in racing.
N
- Narrowband O2 sensor · narrowband, switching lambda sensor, zirconia O2 sensor
A narrowband O2 sensor is a switching exhaust oxygen sensor whose voltage jumps sharply as the mixture crosses stoichiometric, reading high when rich and low when lean.
- Nitrous oxide injection · nitrous, N2O, NOS
Nitrous oxide injection is a system that sprays nitrous oxide (N2O) into an engine's intake so it can burn extra fuel.
- No lift shift (flat shift) · NLS, no-lift shift, flat shift
No lift shift is a manual-transmission feature that lets the driver change gear without lifting off the accelerator.
- NOx sensor · nitrogen oxide sensor, NOx probe, smart NOx sensor
A NOx sensor is an exhaust sensor that measures the concentration of nitrogen oxides (NO and NO2) so the engine controller can run and monitor NOx aftertreatment.
O
- OBD-II PIDs · OBD2 PIDs, parameter IDs, SAE J1979 PIDs
OBD-II PIDs are the standardized parameter identifiers a scan tool uses to request live data from a vehicle's emissions-related modules.
- Octane rating (RON, MON, AKI) · octane, RON, MON
Octane rating is a measure of a fuel's resistance to knock, the uncontrolled auto-ignition of unburned mixture.
- Oil pressure sensor · oil pressure sender, oil pressure transducer, OPS
An oil pressure sensor is a transducer that measures engine oil pressure in the main gallery and sends a proportional signal to a gauge, ECU or logger.
- Oxygen (O2) sensor · O2 sensor, lambda sensor, lambda probe
An O2 sensor (oxygen sensor, or lambda sensor) is an exhaust sensor that measures how much oxygen is left after combustion, telling the ECU whether the mixture is rich or lean.
P
- Peak-and-hold injector driver · peak and hold, peak-and-hold drive, current-controlled injector driver
A peak-and-hold injector driver is an output stage that opens a fuel injector with a short burst of high current, then drops to a lower holding current for the rest of the pulse.
- Piggyback ECU · piggyback, piggyback controller, interceptor
A piggyback ECU is an add-on module wired between the factory engine controller and some of its sensors or outputs.
- Port fuel injection · PFI, MPI, multi-point injection
Port fuel injection is a fuel-injection method with one injector per cylinder that sprays into the intake port, upstream of the intake valve.
- Power distribution module (PDM) · PDM, power distribution unit, PDU
A power distribution module is an electronic unit that switches and protects a vehicle's electrical loads with solid-state outputs instead of relays and fuses.
- Pre-ignition · preignition, pre ignition, hot-spot ignition
Pre-ignition is ignition of the air-fuel mixture before the spark plug fires, started by a hot spot such as an overheated plug tip, glowing carbon or a hot exhaust valve.
- Pressure ratio (turbo compressor) · PR, compressor pressure ratio, boost pressure ratio
Pressure ratio is the absolute pressure at a turbo compressor's outlet divided by the absolute pressure at its inlet.
- Pulse-width modulation (PWM) · PWM, PWM output, PWM control
Pulse-width modulation is a way of controlling power to a load by switching it fully on and off at a fixed frequency and varying the fraction of each cycle it is on.
R
- Race gas · race fuel, racing gasoline, leaded race fuel
Race gas is gasoline blended for competition engines, with far higher knock resistance than pump fuel and a tightly controlled recipe.
- Returnless fuel system · returnless fuel, electronic returnless fuel system, ERFS
A returnless fuel system is a fuel supply with no return line from the engine to the tank.
- Rev limiter (fuel cut vs spark cut) · rev limiter, rpm limiter, revolution limiter
A rev limiter is an engine controller function that stops engine speed from exceeding a set maximum by cutting fuel, cutting spark, retarding ignition or closing the throttle.
- Reverse polarity protection · reverse battery protection, reverse voltage protection, reverse polarity diode
Reverse polarity protection is circuitry that prevents damage when a supply is connected backwards, such as a battery or jump leads reversed.
- Rolling anti-lag · rolling ALS, roll anti-lag, rolling launch anti-lag
Rolling anti-lag is an engine control mode that builds turbo boost while the car is moving at a steady, limited speed, so it can accelerate from a roll with boost already up.
- Roots supercharger · Roots blower, Roots-type supercharger, lobe blower
A Roots supercharger is a belt-driven, positive displacement blower that uses two meshing lobed rotors to carry a fixed volume of air per revolution from inlet to outlet.
S
- Sample rate (data logging) · logging rate, sampling rate, sampling frequency
Sample rate is how many times per second a data logger records each channel, measured in hertz (Hz).
- Sensor reference voltage (5 V reference) · 5V reference, 5 volt reference, VREF
Sensor reference voltage is the regulated supply, usually 5 V, that an ECU provides to its analog sensors such as TPS, MAP and pressure sensors.
- Sequential fuel injection (vs batch fire) · sequential injection, SFI, SEFI
Sequential fuel injection is a mode in which each cylinder's injector fires once per engine cycle, timed to that cylinder's intake stroke.
- Sequential gearbox · sequential transmission, sequential manual transmission, sequential dog box
A sequential gearbox is a manual transmission in which the lever only selects the next higher or lower gear, by rotating a shift drum that moves the selector forks.
- Smart coil (igniter coil) · smart coil, coil with integrated igniter, logic-level coil
A smart coil is an ignition coil with a built-in power transistor, the igniter, so the ECU sends only a low-current logic signal to control dwell and spark.
- Solid state relay (SSR) · SSR, solid-state relay, MOSFET relay
A solid state relay (SSR) is an electronic switch that turns a load on and off with semiconductors instead of moving contacts.
- Spark plug heat range · heat range, hot plug, cold plug
Spark plug heat range is a measure of how quickly a plug moves heat from its firing tip into the cylinder head.
- Speed density · speed-density, SD, MAP-based fueling
Speed density is an engine-load strategy in which the ECU estimates the air mass in each cylinder from engine speed, manifold absolute pressure and intake air temperature, using a volumetric efficiency table.
- Standalone ECU · standalone engine management, aftermarket ECU, programmable ECU
A standalone ECU is an engine control unit that fully replaces the factory engine computer, running fuel, ignition and other functions from its own fully adjustable calibration.
- Star ground · star grounding, single-point ground, common ground point
A star ground is a wiring layout in which separate ground wires run from each device or circuit to one common point, rather than sharing a daisy-chained return.
- Stoichiometric ratio · stoich, stoichiometric AFR, chemically correct mixture
The stoichiometric ratio is the exact air-fuel ratio at which all the fuel and all the oxygen can react completely, leaving neither in excess.
T
- Table interpolation · map interpolation, bilinear interpolation, lookup table interpolation
Table interpolation is the method an engine computer (ECU) uses to calculate a value between the stored cells of a calibration table.
- Target lambda table · lambda target table, target AFR table, AFR target map
A target lambda table is an ECU map, usually indexed by engine speed and load, that sets the mixture strength the engine should run at each operating point.
- Throttle body · throttle, throttle valve, throttle plate
A throttle body is the valve assembly between the air intake and the intake manifold that controls how much air a spark-ignition engine draws in.
- Throttle position sensor (TPS) · TPS, TPS sensor, throttle position sensor
A throttle position sensor (TPS) is a sensor on the throttle shaft that reports throttle opening to the ECU as a voltage.
- Top dead center (TDC) · TDC, top dead centre, TDC compression
Top dead center (TDC) is the crankshaft position where a piston is at the very top of its stroke, farthest from the crankshaft.
- Torque converter lockup · TCC, torque converter clutch, lockup clutch
Torque converter lockup is the engagement of a clutch inside an automatic transmission's torque converter that mechanically joins the engine-driven impeller to the turbine.
- Torque management · torque reduction, torque limiting, torque intervention
Torque management is the set of engine control functions that deliberately limit or reduce engine torque to protect the driveline, smooth gear shifts, control wheel slip or meet driver and safety limits.
- Torque-based engine management · torque-based ECU, torque structure, torque model
Torque-based engine management is an ECU architecture in which requests from the driver and other systems are expressed as engine torque.
- Traction control (engine-based) · TCS, ASR, traction control system
Traction control is a system that limits driven-wheel slip by reducing engine torque, and in many cars by braking a spinning wheel.
- Transmission control module (TCM) · TCM, TCU, transmission control unit
A transmission control module (TCM) is the electronic controller that runs an automatic or automated transmission.
- Turbo compressor map · compressor map, turbo map, compressor efficiency map
A turbo compressor map is a chart of a compressor's performance, plotting pressure ratio against air mass flow.
- Turbo lag · boost lag, turbo response, spool time
Turbo lag is the delay between opening the throttle and the turbocharger delivering boost, when engine speed is already high enough for the turbo to make boost.
- Twin-screw supercharger · twin screw blower, screw supercharger, Lysholm compressor
A twin-screw supercharger is a belt-driven, positive displacement compressor that uses a pair of meshing helical rotors, one male and one female, to trap air and squeeze it as it moves along the rotors.
- Twin-scroll turbo · twin-scroll turbocharger, divided turbine housing, divided-entry turbo
A twin-scroll turbo is a turbocharger whose turbine housing has two separate exhaust inlets and passages, each fed by a group of cylinders whose exhaust pulses do not overlap.
- Two-step (2-step launch limiter) · 2 step, 2-step, two step
A 2 step is a second, lower rev limiter that holds engine speed at a set launch rpm while the car is stationary, usually armed by a clutch switch or button.
U
- Unified Diagnostic Services (UDS) · UDS, ISO 14229, UDS protocol
Unified Diagnostic Services is the diagnostic communication protocol defined by ISO 14229 that tools use to talk to vehicle control modules.
V
- Valve overlap · overlap, cam overlap, overlap period
Valve overlap is the period around top dead center at the end of the exhaust stroke when the intake and exhaust valves are open at the same time.
- Variable reluctance (VR) sensor · VR sensor, magnetic pickup, inductive sensor
A variable reluctance sensor is a passive speed and position sensor made of a magnet and a coil.
- Variable valve timing (VVT / cam phasing) · VVT, cam phasing, cam phaser
Variable valve timing is a system that shifts when the engine's valves open and close while it runs, usually by rotating the camshaft relative to its drive sprocket with an oil-pressure phaser.
- Vehicle speed sensor (VSS) · VSS, VSS sensor, output shaft speed sensor
A VSS sensor (vehicle speed sensor) is the sensor that reports how fast the vehicle is moving, usually by reading a toothed ring on the transmission output shaft.
- Voltage drop · voltage drop test, IR drop, line loss
Voltage drop is the voltage lost across a wire, connector, switch or ground as current flows through its resistance.
- Volumetric efficiency (VE) · VE, volumetric efficiency, breathing efficiency
Volumetric efficiency (VE) is the ratio of the air mass an engine actually draws into its cylinders per cycle to the mass that would fill the swept volume at a reference density.
- VTEC · Variable Valve Timing and Lift Electronic Control, i-VTEC, VTEC-E
VTEC is Honda's Variable Valve Timing and Lift Electronic Control system, which switches each cylinder's valves between a mild cam profile and a high-lift, longer-duration profile using hydraulic pins in the rocker arms.
W
- Warm-up enrichment · WUE, cold start enrichment, after-start enrichment
Warm-up enrichment is the extra fuel an ECU adds while an engine is below normal operating temperature, scheduled mainly by coolant temperature.
- Wasted spark ignition · wasted spark, distributorless ignition, DIS
Wasted spark ignition is a distributorless system in which one coil fires two spark plugs at once, on cylinders whose pistons reach top dead center together.
- Wastegate · waste gate, internal wastegate, external wastegate
A wastegate is a valve on the exhaust side of a turbocharger that lets some exhaust gas bypass the turbine.
- Water-methanol injection · meth injection, water meth, WMI
Meth injection, or water-methanol injection, sprays a mixture of water and methanol into the intake air, usually under boost, to cool the charge and suppress knock.
- Wheel speed sensor · WSS, ABS sensor, ABS wheel speed sensor
A wheel speed sensor is a sensor at each wheel hub that reads a toothed or magnetic tone ring to measure wheel rotation speed.
- Wideband O2 sensor · wideband, wideband lambda sensor, UEGO
A wideband O2 sensor is an exhaust oxygen sensor that reports the actual lambda value across rich and lean mixtures, not just whether the mixture is rich or lean of stoichiometric.

