Injector short pulse width

short pulse addersmall pulse width correctioninjector non-linear regionminimum pulse widthballistic regionshort pulse width compensation

Injector short pulse width is the range of very short injection pulses, typically the first one or two milliseconds, where fuel delivered no longer scales linearly with pulse length. The needle may not fully open before closing again, so ECUs add a short pulse correction on top of dead time to deliver accurate fuel at idle and light load.Medium123

How it works

For most of its range an injector behaves simply: fuel mass equals flow rate times the pulse width beyond dead time.

That model assumes the needle travels fully open, stays there and then closes. In very short pulses the needle can turn around partway through its stroke, a regime often called ballistic.Medium13

In the ballistic region, delivered fuel depends on how far the needle got and how it bounces, which varies between injector designs and even between units. The flow curve bends and can have bumps. Dead time alone cannot correct it because the error changes with pulse length.Medium12

Supply voltage moves the whole low-end curve. An SAE study on injector dead time found that lower supply voltage lengthens the opening delay, so voltage compensation and short pulse correction interact. Characterization data should be measured over the voltages the vehicle actually sees.2

In tuning

Large injectors chosen for high power spend idle and cruise in this region.

If the ECU lacks accurate short pulse data, idle lambda wanders, off-throttle transitions go rich or lean, and closed-loop trims work hard. Use the injector maker's characterization data where it exists instead of tuning the fuel table around the error.Medium12

Raising fuel pressure, or choosing an injector with good low-end linearity, also moves idle pulse widths out of the worst region. Check that minimum pulse width under decel and light load stays above the point where delivery becomes unpredictable.Low13

Formula and worked example

PW_cmd = PW_eff + t_dead(V) + Δt_short(PW_eff)
PW_cmd
commanded electrical pulse widthms
PW_eff
effective pulse width for the required fuel mass at nominal flow ratems
t_dead(V)
dead time at the current supply voltagems
Δt_short
short pulse correction, near zero outside the non-linear regionms
Medium12

Try it

hp
:1

Typical: gasoline NA 0.45-0.50, gasoline boosted 0.55-0.65, E85 NA 0.65-0.75, E85 boosted 0.80-0.90 lb/hp-hr.

%

Size for 80-85% so the injector still has control margin at peak power.

Result

Flow per injector75.0 lb/hr
Total fuel flow240 lb/hr

Planning estimate from the formula below, not a measurement.

Open the full fuel injector size calculator →

Myths vs facts

Myth Dead time fixes all injector error at idle.

Fact Dead time is a constant offset for a given voltage and pressure. The short pulse error changes with pulse length, so it needs its own correction curve.Medium12

Myth Poor idle with big injectors means the fuel table needs more tuning.

Fact Tuning the main fuel table around an injector characterization error usually spreads problems elsewhere. Correct injector data first, then tune the table.Medium1

Frequently asked

Why do big injectors idle badly?

An oversized injector needs only a very short pulse at idle, which can fall into the region where delivery is non-linear and inconsistent. Without accurate short pulse correction, each cylinder gets slightly different fuel each cycle, so lambda hunts and idle becomes rough. Better characterization data or higher fuel pressure usually helps.Medium13

What is a short pulse adder?

It is a correction table that adds or subtracts a small amount of pulse width at very short pulse lengths. It compensates for the gap between the simple linear flow model and the injector's real delivery when the needle does not fully open. Values come from bench characterization of the injector.Medium12

What is the minimum injector pulse width?

There is no universal number. It is the shortest pulse that still delivers repeatable fuel for that injector, pressure and voltage, and comes from the maker's data or flow-bench testing. Many port injectors become unreliable somewhere below about one millisecond of effective pulse, but the figure varies widely.Low13

How do you calibrate small pulse widths?

The accurate way is bench testing: measure fuel delivered over many pulses at each pulse width, pressure and voltage, then fit a correction. On the car, stable idle and light-load logs with a wideband can confirm whether lambda errors follow pulse width rather than load or rpm.Medium21

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Influence of Supply Voltage over Fuel Injector's Deadtime (SAE 2025-36-0174) · SAE International · sae-paper · retrieved 2026-10-27
  3. Fuel injection · Wikipedia · reference · retrieved 2026-10-27