Peak-and-hold injector driver

peak and holdpeak-and-hold drivecurrent-controlled injector driverP&H driverpeak and hold injection

A peak-and-hold injector driver is an output stage that opens a fuel injector with a short burst of high current, then drops to a lower holding current for the rest of the pulse. The high peak snaps the valve open quickly, while the low hold current keeps it open without overheating the coil or driver.123

How it works

An injector is a solenoid valve.

Its coil inductance resists changes in current, so current rises along a curve after the driver switches on. The needle lifts only once the magnetic force overcomes spring and fuel pressure. A higher current reaches that force sooner, which shortens opening time.451

Once the needle is open, the magnetic circuit gap is smaller and much less current holds it there. A peak-and-hold driver regulates current in two phases: it lets current climb to a peak threshold, then chops the output on and off, usually with pulse-width modulation, to hold a lower average current until the pulse ends.163

The alternative is a saturated driver, which simply connects the coil to battery voltage for the whole pulse. Current is then limited only by coil resistance. That works for high-impedance injectors of around 12 Ω, such as Bosch's EV 14 family, but a low-impedance coil of a few ohms would draw too much current and overheat.721

Dedicated driver chips do this in hardware. NXP's MC33816, for example, is a programmable solenoid driver with several high-side and low-side pre-drivers for external MOSFETs, used to shape injector current profiles. Direct-injection systems use the same idea with a boosted voltage for the peak phase.Medium31

In tuning

Driver type changes injector dead time.

A fast peak-and-hold profile opens the needle sooner than a saturated drive on the same injector, so dead-time tables must be measured with the driver and voltage actually used. Copying dead-time data measured on a different driver gives errors at short pulse widths.Medium81

Match the driver to the injector before first start. Low-impedance injectors need peak-and-hold outputs or series ballast resistors; high-impedance injectors run on saturated outputs. Wrong peak or hold settings can make the injector open late, flutter or overheat.Medium12

Formula and worked example

I_final = V / R
I_final
steady-state coil current with a saturated driverA
V
supply voltage across the coilV
R
coil resistanceΩ
51

Myths vs facts

Myth Peak-and-hold injectors and saturated injectors are different internally in a way the ECU cannot handle.

Fact The difference is coil resistance and the drive strategy. Low-impedance injectors need current limiting, by a peak-and-hold driver or ballast resistors; the valve mechanism itself works on the same solenoid principle.Medium21

Myth A higher peak current always gives better injector control.

Fact Peak current must suit the injector. Too little opens it slowly; too much adds heat and stress on the coil and driver. Use the injector maker's recommended profile.Medium13

Frequently asked

What is a peak and hold injector driver?

It is an ECU output that controls injector current in two stages. It first allows a high peak current so the injector opens fast, then switches to a lower regulated hold current for the rest of the pulse. This suits low-impedance injectors, which would draw too much current if connected straight to battery voltage.12

Do low impedance injectors need peak and hold?

They need current limiting of some kind. A peak-and-hold driver is the usual choice. The older alternative is a ballast resistor pack in series with each injector, which lets a saturated driver run them at the cost of slower opening and wasted heat in the resistors.Medium21

What is the difference between peak and hold and saturated drive?

A saturated driver switches the injector fully on for the whole pulse and lets coil resistance set the current, which suits high-impedance injectors near 12 Ω. A peak-and-hold driver actively regulates current, using a high peak to open and a lower hold to stay open, which suits low-impedance injectors.71

What are typical peak and hold currents?

They depend on the injector and should come from its maker. Low-impedance port injectors are often described with peak currents of a few amps and hold currents around a quarter of that, but figures vary by design. Direct injectors use much higher peaks with a boosted voltage.Low13

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Fuel injection · Wikipedia · reference · retrieved 2026-10-27
  3. MC33816: SD6 programmable solenoid controller (product page) · NXP Semiconductors · vendor-doc · retrieved 2026-10-27
  4. Solenoid valve · Wikipedia · reference · retrieved 2026-10-27
  5. Inductor · Wikipedia · reference · retrieved 2026-10-27
  6. Pulse-width modulation · Wikipedia · reference · retrieved 2026-10-27
  7. Injection Valve EV 14 data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  8. Influence of Supply Voltage over Fuel Injector's Deadtime (SAE 2025-36-0174) · SAE International · sae-paper · retrieved 2026-10-27