Low-side switch

low side driverground-switched outputopen-drain outputLSDlow-side output

A low-side switch is a switch placed between a load and ground, with the load's other end permanently connected to positive supply. Turning it on completes the ground path. Engine controllers commonly use low-side MOSFET or transistor outputs to drive injectors, relay coils, solenoids and some ignition coils.123

How it works

An N-channel MOSFET on the low side has its source at ground, so it can be driven directly by a logic-level gate signal with no charge pump. That makes low-side drivers simple, cheap and efficient, which is why multichannel driver chips such as TI's seven-channel TPL7407L are common.Medium13

Many loads are inductive. When a low-side switch opens, the coil drives its terminal far above supply. Drivers either include clamp or free-wheeling diodes, as the TPL7407L does for inductive kickback, or rely on an external flyback diode or an active voltage clamp.14

The trade-off is that the load is always at supply potential. A wire shorted to chassis between the load and the switch turns the load on with no protection from the switch. Fusing on the positive feed protects the wiring in that case.Medium25

In tuning

Fuel injectors are normally fed switched 12 V and grounded by the engine controller's low-side drivers.

The fast clamp voltage at turn-off affects how quickly the injector closes, which is one reason injector dead time varies between driver designs.Medium67

When using a low-side output to trigger a relay, connect one coil terminal to switched positive and the other to the output. Use a relay with a suppression diode or confirm the output is clamped.Medium14

Myths vs facts

Myth A low-side output supplies voltage to the load.

Fact It does not. It only connects the load to ground. A meter between the output pin and ground shows supply voltage when the output is off and near zero when on, which surprises people testing for a voltage signal.Medium12

Myth Low-side switching is unsafe for all automotive loads.

Fact It is standard for injectors, ignition drivers and relay coils. The concern is that shorts to ground on the load side bypass the switch, so upstream fusing must protect the wire.Medium25

Frequently asked

Why do ECUs switch injectors on the ground side?

Low-side N-channel switches are easy to drive from logic, cheap, efficient and fast. With the injector fed from switched positive, the controller only needs to complete the ground path for the exact pulse width. The driver's clamp then controls how quickly the injector closes after the pulse ends.Medium316

Can a low-side output drive a relay?

Yes, if the relay coil current is within the output's rating. Feed one coil terminal from switched positive and connect the other to the output. Make sure the coil's turn-off spike is clamped by a diode in the relay, a flyback diode, or a clamp inside the driver.14

What is a ground-switched output?

It is another name for a low-side output. The controller switches the load's ground connection on and off while the load stays connected to positive supply. Datasheets may call it an open-drain or open-collector output when the switch is a bare transistor without an internal pull-up.Medium32

How do you test a low-side output with a meter?

Measure from the output pin to ground with the load connected. When off, the pin sits near supply voltage through the load; when on, it pulls close to zero. Measuring with the load disconnected can give misleading readings, because an open-drain output has nothing pulling it up.Medium13

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. TPL7407L 40-V 7-channel low side driver data sheet (SLRS066) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  2. Low-side switches product family · Infineon Technologies · vendor-doc · retrieved 2026-10-27
  3. Power MOSFET · Wikipedia · reference · retrieved 2026-10-27
  4. Flyback diode · Wikipedia · reference · retrieved 2026-10-27
  5. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  6. Fuel injection · Wikipedia · reference · retrieved 2026-10-27
  7. Influence of Supply Voltage over Fuel Injector's Deadtime (SAE 2025-36-0174) · SAE International · sae-paper · retrieved 2026-10-27