Flyback diode

freewheeling diodesnubber diodesuppression diodekickback diodecatch diodeclamp diode

A flyback diode is a diode placed across an inductive load, such as a relay coil or solenoid, to give its current a path when the switch turns off. It prevents the large voltage spike the inductor would otherwise create, protecting the driver transistor and nearby electronics.123

How it works

An inductor resists changes in current.

When a switch opens suddenly, the coil drives its voltage as high as needed to keep current flowing, following V = L × di/dt. With no path, that spike can reach hundreds of volts and break down the switch.21

The diode sits across the coil, reverse-biased in normal operation. At turn-off, the coil's voltage reverses and the diode conducts, letting current circulate and decay through the coil resistance while the voltage is held to about one diode drop.14

Many driver chips include clamps. TI's TPL7407L low-side driver array has internal clamp diodes for inductive loads, and the TPS1H100-Q1 high-side switch clamps the negative voltage from an inductive load. External diodes are still common on relays and solenoids driven by discrete transistors.56

In tuning

A plain diode slows release.

Holding the voltage near zero makes current decay slowly, so relays drop out and solenoids close later. Fast actuators such as injectors use a higher clamp voltage, often a zener or the driver's active clamp, so current falls quickly.Medium17

Fit the diode with the correct orientation: cathode to the positive side of the coil. Reversed, it shorts the supply through the switch every time the coil turns on.14

Formula and worked example

V = L × di/dt
V
induced voltage across the coilV
L
coil inductanceH
di/dt
rate of change of currentA/s
2

Myths vs facts

Myth A flyback diode has no effect on how the load behaves.

Fact It changes turn-off speed. A plain diode makes current decay slowly, delaying relay dropout and solenoid closing. That matters for fast-switching actuators.1

Myth All relays already have a diode inside.

Fact Some relays include a diode or resistor across the coil, and those may be polarity-sensitive. Many do not. Check the relay's markings or data sheet.Medium13

Frequently asked

What does a flyback diode do?

It gives an inductive load's current somewhere to go when the switch turns off. Without it, the coil's collapsing magnetic field creates a high voltage spike that can damage the transistor or relay contacts driving it. The diode clamps that spike to a safe level.12

Do relays need a flyback diode?

The relay coil does when it is switched by a transistor or ECU output without its own clamp. Many ECU and PDM outputs include internal clamps, and some relays include a diode or resistor. If neither is present, add a diode across the coil, cathode to positive.Medium15

Why does a flyback diode slow a solenoid?

The diode holds the coil voltage near zero at turn-off, so current decays slowly through the coil's own resistance. The magnetic field lingers and the solenoid releases later. Higher-voltage clamps, such as zener diodes, make current fall faster.1

Where does the flyback diode go?

Directly across the coil terminals, with the cathode on the positive supply side and the anode on the side connected to the switch. Placing it close to the coil keeps the loop small and reduces radiated noise.14

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Flyback diode · Wikipedia · reference · retrieved 2026-10-27
  2. Inductor · Wikipedia · reference · retrieved 2026-10-27
  3. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  4. Diode · Wikipedia · reference · retrieved 2026-10-27
  5. TPL7407L 40-V 7-channel low side driver data sheet (SLRS066) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  6. TPS1H100-Q1 40-V, 100-mOhm single-channel smart high-side power switch data sheet · Texas Instruments · vendor-doc · retrieved 2026-10-27
  7. MC33816: SD6 programmable solenoid controller (product page) · NXP Semiconductors · vendor-doc · retrieved 2026-10-27