Pulse-width modulation (PWM)

PWMPWM outputPWM controlpulse-width modulated outputPWM frequency

Pulse-width modulation is a way of controlling power to a load by switching it fully on and off at a fixed frequency and varying the fraction of each cycle it is on. ECUs use PWM to drive boost solenoids, idle valves, fuel pumps, fans and electronic throttle motors.123

How it works

Two numbers define a PWM signal

Frequency, how many cycles happen per second, and duty cycle, the percentage of each cycle the output is on. The average voltage at the load is roughly the supply voltage multiplied by the duty cycle.12

Switching fully on or off keeps the transistor's losses low, because it is either carrying current with little voltage across it or blocking voltage with no current. That is why PWM is far more efficient than dropping voltage through a resistor.14

Inductive loads like solenoids and motors smooth the pulses into a near-steady current. Motor drivers such as TI's DRV8873-Q1 H-bridge accept PWM inputs to set motor speed and direction.Medium56

In tuning

Frequency must suit the actuator.

Solenoid valves need a frequency low enough to open and close fully within each cycle, or control becomes nonlinear. Motors and fans run quieter at higher frequencies. Use the actuator maker's recommended frequency where one is published.Medium53

Battery voltage changes the result. The same duty cycle gives a higher average voltage at 14 V than at 12 V, so duty tables for solenoids and pumps often include a voltage correction.Medium13

Formula and worked example

V_avg = D × V_supply
V_avg
average voltage at the loadV
D
duty cycle as a fraction (0 to 1)
V_supply
supply voltageV
12

Myths vs facts

Myth Higher PWM frequency is always better.

Fact Solenoids need time to move each cycle. Above their useful frequency they stop following the signal and behave as if they were at a fixed position, which makes control nonlinear.Medium53

Myth A PWM output is the same as an analog voltage output.

Fact It switches between full supply and zero. Electronics that expect a steady voltage, such as some gauges or sensor inputs, can misread a PWM signal unless it is filtered.1

Frequently asked

What is PWM in a car?

PWM is a way of controlling devices like boost solenoids, fans, fuel pumps and idle valves by switching them on and off rapidly. The ECU varies the on-time percentage, the duty cycle, to set the average power the device receives, which controls its position or speed.13

What PWM frequency should I use?

Use the actuator maker's recommendation. Solenoid valves generally run at lower frequencies so they can move fully each cycle, while motors and fans often use higher ones to reduce noise. Too high a frequency for a solenoid makes its response nonlinear.Medium53

How does PWM control a solenoid?

The solenoid coil's inductance smooths the switched voltage into an average current. More duty means more current and more magnetic force against the valve's spring. At a suitable frequency, the valve either holds a partial position or opens and closes each cycle, giving an average flow.Medium51

Why does PWM need battery voltage compensation?

Average voltage equals duty multiplied by supply voltage. When the battery drops from charging voltage to resting voltage, the same duty delivers less voltage and current, so the actuator moves less. Voltage compensation adjusts duty to keep the result constant.Medium13

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Pulse-width modulation · Wikipedia · reference · retrieved 2026-10-27
  2. Duty cycle · Wikipedia · reference · retrieved 2026-10-27
  3. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  4. Power MOSFET · Wikipedia · reference · retrieved 2026-10-27
  5. Solenoid valve · Wikipedia · reference · retrieved 2026-10-27
  6. DRV8873-Q1 automotive H-bridge motor driver data sheet (SLVSDY7) · Texas Instruments · vendor-doc · retrieved 2026-10-27