Jeep Wrangler LS Swap (TJ 1997-2006 and JK 2007-2018): Mounts, Transfer Case Adapters, Fuel, CAN Bus Integration and Legal Guide

The LS swap Jeep Wrangler owners most often do is the 1997-2006 TJ, which has mature mount, adapter and fuel kits. The 2007-2018 JK is harder because its cluster, transmission and body module share CAN data. Both need frame mounts, a GM transmission adapted to the Jeep transfer case, new driveshafts and a GM-ready radiator.Medium141426

Difficulty4/5 · HardMedium234132427
  • TJ mounts are weld-in or bolt-in kits; JK mounts we could verify are weld-in only.
  • The factory TJ automatics and the NSG370 six-speed are not suited to GM torque, so most builds add a GM automatic and a transfer case adapter.
  • The JK cluster, transmission and body module expect engine data on the CAN bus; complete JK kits with bridge modules have been discontinued or withdrawn.
  • Driveshafts, radiator, fan control and fuel pressure all change, and emissions approval is hard.

At a glance

The key numbers and parts, with the source on each tile.

Stock engines
  • TJ: 2.5 L four (to 2002), 2.4 L four (2003+) and 4.0 L six, which Jeep rated at 190 hp and 235 lb-ft319 N·m
  • JK: 3.8 L V6 (2007-11, rated 202 hp) and 3.6 L Pentastar (2012-18, rated 285 hp)
Sourced · medium3031
Curb weight
  • TJ 3,092-3,857 lb by model1,403-1,750 kg
  • JK range per Wikipedia 2,760-3,340 lb, with no 2-door/4-door split1,252-1,515 kg
Sourced · medium3031
Mount kits
  • Novak MMTJ-G (TJ/LJ), MMJK-G (2007-2018 JK), MMYJ-G3 (YJ)
  • Hooker BHS513 brackets for the TJ via retailers
Sourced120
Transfer case route
  • Novak 4L61-23 adapts 4L60E/65E/70E to 23-spline NP231 and NP241OR
  • Novak also lists 6L80 kits including JK-era NP241 cases
Sourced1415
Manual gearbox
  • AX15 and NV3550 can stay via Novak GMAX15 and 3504G adapters
  • NSG370 input is rated 272 lb-ft369 N·m
Sourced111013
Driveshafts
  • New lengths in almost every case
  • Novak recommends a short-tail SYE on the NP231 and fixed-yoke shafts
Sourced16174
Cooling
  • GM-outlet aluminum radiators for TJ and JK
  • JK uses the 2012-2018 Pentastar PWM fan with a controller
Sourced897
Fuel
  • 1997-2004 TJ modules regulate about 40 psi (2.8 bar) and need an upgrade to about 58 psi4.0 bar
  • 2005-2006 TJs run about 60 psi natively4.1 bar
Sourced64
Legal route (US)
  • Same-or-newer certified engine with its full emissions system
  • California requires a BAR Referee inspection
Sourced3738

Recommended engines

  • 5.3 LM7 / L59 / LY5 (Gen III/IV truck) · Common, cheap Gen III truck engine that fits the Gen III/IV mount kits Novak lists for the TJ and JK; GM rated it at 270-295 hp depending on year and application.
  • 6.0 LQ4 / LQ9 / LY6 / L96 (truck) · The 6.0 L truck family (LQ4, LY6, L96) shows up in documented JK kit builds, paired with a 6L80E; same Gen III/IV mount pattern as the 5.3 L.
  • LS1 · Aluminum Gen III car engine; Novak lists it about 108 lb (49 kg) lighter than the Jeep 4.0 L six, and its own TJ example build used one.
  • LS3 / L99 · The engine in the Bruiser and Turn Key JK kits; new crate supply with GM installation data, 58x crank trigger and drive-by-wire throttle.

Mounts

Mount kits are the best-documented part of any LS swap Jeep Wrangler builders attempt.

Novak MMTJ-G (TJ/LJ)
  • Frame platforms, upper and lower HNBR isolators, block plates and hardware
  • G3 is weld-in, G6 bolt-in for six-cylinder TJs only
Sourced2
Novak MMJK-G (JK)
  • Fits all 2007-2018 JKs with Gen III/IV engines (not Gen V LT)
  • Weld-in after removing the factory frame mounts
  • 3/16 in steel, 5/8 in through bolts4.8 mm · 16 mm
Sourced3
Hooker BHS513 (TJ)

Uses most stock frame mounts, listed as needing no body or suspension lift, high-arch shape for upper control arm clearance

Sourced · medium20

Novak lists Gen III/IV LS mounts for the YJ (MMYJ-G3), TJ and LJ (MMTJ-G) and the 2007-2018 JK (MMJK-G). Each kit has block plates, frame platforms and HNBR rubber isolators.123

On the TJ, choose between Novak's weld-in MMTJ-G3, which replaces the factory brackets, and the bolt-in MMTJ-G6 for Jeeps built with the inline six. Hooker's BHS513 brackets, sold through retailers, also reuse most stock frame mounts.Medium220

We found no verified bolt-in JK option. Novak's MMJK-G platforms weld on after the factory mounts are cut off and fit Gen III and IV engines only. Universal weld-in kits such as Advance Adapters 713088 suit frames up to 29.35 in (746 mm) wide, and the maker warns against street use before they are welded.322

Novak describes a narrow window for engine placement in the TJ, usually centered or offset 0.5-1 in (13-25 mm) toward the passenger side. Safety: support the engine on a hoist and the Jeep on stands while you cut, fit and weld.24

Transmission

Most documented Wrangler LS swaps use a GM automatic.

Novak 4L61-23
  • Adapts 1996-on six-bolt 4L60E, 4L65E and 4L70E (2WD or 4WD) to 23-spline NP231 and NP241OR
  • 3.0 in long, includes a GM speed sensor and reluctor76 mm
Sourced14
NSG370 rating
  • Input rated 272 lb-ft369 N·m
  • Fitted to 2005-2006 TJs and 2007-2018 JKs
Sourced133031
JK automatics
  • Bruiser's JK kit required replacing the 42RLE with a NAG1 (W5A580)
  • RPM Extreme and Turn Key kits used the 6L80E
Sourced · medium242625

Novak's 4L61 kit joins a 4L60E, 4L65E or 4L70E to the NP231 or Rubicon NP241OR and replaces the output shaft, so a 2WD or 4WD donor works. The transmission must be opened, and Novak suggests a transmission shop.144

JK kits used newer automatics. RPM Extreme built its 2007-2011 kit around a 6L80E with an adapter to the non-Rubicon 241J, Turn Key paired a 6L80E with a separate controller, and Bruiser used the NAG1. Novak lists 6L80 adapters for JK-era NP241 cases.Medium26252415

Manual TJs can keep the gearbox. Novak's GMAX15 kit adapts the 1997-1999 AX15 and kit 3504G the 2000-2004 NV3550, both to a GM bellhousing with a GM clutch and a taller LS flywheel. Gen III engines sit about 3 in (76 mm) farther forward than the Jeep six.111030

Treat the NSG370 six-speed with care. Novak lists its input rating at 272 lb-ft (369 N·m), below GM's 315-335 lb-ft rating for the 5.3 L LM7, and lists its GM adapter as discontinued. Novak also rules out the AX5 and the 32RH automatic behind GM power.Medium1333124

Clearance

Check the oil pan against the front axle at full compression, not at ride height.

Oil pan
  • Novak notes most GM pans are rear-sump
  • Hooker lists factory LS/LT truck pans for its YJ brackets
Sourced · medium421
Steering
  • MMTJ-G includes a platform for the steering shaft carrier bearing
  • MMJK-G is shaped to clear the stock shaft and pillow block
Sourced23
Alternator
  • Some LS3 Camaro accessory drives put the alternator into the TJ steering gear
  • Novak suggests a C5 Corvette-style drive
Sourced2

Novak notes most GM pans are rear-sump, and Hooker lists factory LS truck pans for its YJ brackets. We found no maker data on track bar clearance, so cycle the suspension before final welding.Medium421

Steering is the tightest spot in the TJ. Novak's mounts carry the steering shaft carrier bearing bracket, and it warns that some LS3 Camaro accessory drives put the alternator into the steering gear. A C5 Corvette-style drive or a third-party bracket avoids it.2

Novak calls a mandatory TJ body lift a myth, needed only with sagged springs or poor engine placement. JK parts vary: Kooks recommends at least a 2.5 in (64 mm) suspension lift with its long-tube JK headers. Novak's JK mounts need no extra bump stops, unlike JK Hemi mounts.Medium4233

Cooling

Novak says the factory TJ radiator suits neither the capacity nor the hose positions of a GM V8.

TJ radiator

Novak KryoFlow II LS version: 24.25 x 18.5 x 7.5 in (616 x 470 x 191 mm), passenger-side inlet and outlet, steam-port bungs, no transmission cooler

Sourced8
JK radiator

Novak K-JK30H for GM Gen III+ engines in 2007-2018 JKs, 16 psi cap, built to take the 2012-2018 Pentastar fan

Sourced9
JK fan control
  • The 2012-2018 Pentastar fan (green wire) runs only on a PWM command
  • 2007-2011 fans (purple wire) are not supported by Novak's E-PWM
Sourced97

Its LS-version radiator puts both necks on the passenger side and has bungs for a steam vent line, but no transmission cooler, so add a separate cooler for an automatic.48

On the JK, Novak's radiator takes the 2012-2018 Pentastar fan directly. That fan runs only when it sees a PWM command on its green wire, so a GM swap needs a controller such as Novak's E-PWM, which reads a GM-style temperature sensor and reports back to the TIPM.97

If the Jeep computer stays in the loop, it may still expect its own coolant signal to run the fans. One 2011 JKU swapper planned to add a JK sensor to the GM head for that reason. This is a single forum report, so confirm the method with your kit maker.Low28

Fuel

TJ fuel depends on year.

1997-2004 TJ
  • Fuel module regulates about 40 psi2.8 bar
  • Novak FSK-9704 supplies about 58 psi through a returnless line4.0 bar
Sourced6
2005-2006 TJ/LJ
  • Native system near 60 psi4.1 bar
  • Novak says no changes are needed
Sourced4
JK
  • RPM Extreme's kit listed a plug-and-play fuel line adapter
  • No JK pressure data was published
Low confidence26

Novak says 1997-2004 modules regulate to about 40 psi (2.8 bar), short of the roughly 58 psi (4.0 bar) a Gen III rail wants. Its FSK-9704 kit adds an inline regulator and filter on a returnless supply line, while 2005-2006 TJs already run about 60 psi (4.1 bar).64

Pick the FSK-9704NR version if your engine already has a regulator on the fuel rail, as many 1997-2002 LS and Vortec engines do. Fitting both regulators in series sets the wrong pressure.6

JK kits adapted the in-tank supply to the GM rail, and RPM Extreme listed a plug-and-play line adapter. Put a gauge on the rail and confirm pressure at full load before the first drive. Safety: drop the tank near empty, relieve pressure before opening lines, and keep sparks and heat away.Low266

Exhaust

Novak recommends tight, block-hugging headers in the TJ, with one oxygen sensor bung welded into each downpipe.

Novak LSJK headers

LSJK134P (plain) and LSJK134C (ceramic): short block-hugging, 1-3/4 in (44 mm) primaries, 3 in (76 mm) collector, no CARB executive order

Sourced18
Kooks JK long tubes

37102200 for 4-door JKs: 1-3/4 in primaries, requires RPM Extreme-style mount plates and Gen IV hydraulic mounts

Sourced · medium23
TJ guidance

Novak recommends block-hugging headers, one oxygen sensor bung per bank, and headers covered by a CARB executive order in California

Sourced4

A Y-pipe ahead of the transmission or behind the transfer case joins the banks; 2.5 in (64 mm) pipe is usually enough. Keep the factory heat shields over the converter and muffler.4

For the JK, Novak's LSJK headers sweep the passenger side to clear the gap between starter and frame, and route under the pan, under the bellhousing slope or behind the transfer case. Novak states they carry no CARB executive order.18

Long-tube JK headers exist for kit-specific mounts. Kooks lists a 4-door JK set that needs RPM Extreme-style mount plates and Gen IV hydraulic mounts, recommends a 2.5 in (64 mm) lift, and warns that 2-door Jeeps may need the fuel tank moved.Medium23

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads

The GM harness and computer run the engine; the real question is how the Jeep's systems keep working.

TJ cluster

1996-on Jeep clusters are electronic and take a multiplexed signal from the Jeep computer

Sourced4
Tach emulator
  • Novak E-TX turns the GM tach output into crank pulses for the Jeep computer
  • Listed for TJs and 2007-2010 JK 3.8 L
  • Stock GM computers only
Sourced5
JK kit integration
  • RPM Extreme used a CAN translation module plus reprogramming of the Jeep, GM and TIPM computers
  • Bruiser kept the factory Chrysler computer and OBD port
Low confidence2624

Novak says 1996-on Jeep clusters take a multiplexed signal from the Jeep computer, so you either fit a GM-compatible aftermarket cluster or keep the Jeep computer running alongside the GM one.4

Keeping the Jeep computer means feeding it the signals it expects. Novak's E-TX converts the GM tach output into crank pulses so the Jeep computer can put engine speed on the bus to the cluster. It covers TJs and 2007-2010 JKs with the 3.8 L.5

The Jeep speedometer reads the Jeep transfer case sensor, one reason Novak advises against Chevy NP231 cases. The GM computer needs its own speed input: Novak's 4L61 kit includes a GM sensor and reluctor, and PSI notes LS computers expect a 128k pulse signal.Medium41434

The JK shares engine data with the cluster, transmission, stability control and body module (TIPM). RPM Extreme described a module translating between the GM and Jeep CAN networks, while Bruiser kept the Chrysler computer in control. Neither published how the immobilizer is handled, and both kits are no longer sold as described.Low31262427

Chrysler security data lives in more than one module, and technicians report start-then-stall faults when it does not match. Ask any current JK kit maker how the immobilizer, ABS and stability control are handled before buying. Safety: disconnect the battery and fuse every new feed.Low3629

Chassis

Engine weights (Novak, accessory-loaded)
  • Jeep 4.0 L six about 515 lb234 kg
  • GM Gen III aluminum about 407 lb185 kg
  • Gen III iron about 470 lb213 kg
Sourced · medium4
TJ rear axles
  • Dana 35 on the Sport
  • Dana 44 on Unlimited and Rubicon, optional on Sport and Sahara
Sourced · medium30
Wheelbase
  • TJ 93.4 in2,372 mm
  • LJ about 103.4 in2,626 mm
  • JK 2-door 95.4 in (2,423 mm), 4-door 116 in2,946 mm
Sourced · medium3031

Novak lists the Jeep 4.0 L six at about 515 lb (234 kg) and an aluminum Gen III V8 at about 407 lb (185 kg), both with accessories, so the nose rarely gets heavier. It reports factory TJ springs are usually fine for a small V8.Medium4

Axles are the part to plan around. TJ Sports came with a Dana 35 rear, while Unlimiteds and Rubicons got a Dana 44. Novak considers the factory Dana 30 and 35 able to take the power but leaves upgrades to the builder's use.Medium304

Gearing follows tire size. A JK kit vendor suggested 4.10 gears for 35 in tires and 4.56 for 37s with an LS3; treat that as a starting point and check cruise rpm with a gear-speed calculator. Welding burns the frame coating near new mounts, so refinish it.Low273

Tuning

A donor GM computer needs a calibration for the Jeep: injectors, transmission and speed input.

Active Fuel Management
  • Most Gen IV 5.3 L engines have AFM cylinder deactivation
  • The Gen III LM7 does not
Sourced · medium3233
Break-in

GM says to avoid maximum engine speed and long high-load periods for the first 500 miles (12 to 15 engine hours)

Sourced35

Novak advises pairing each engine with a GM computer of the same model year and notes many installs need reprogramming, which dealers and tuning shops commonly do.Medium194

Gen IV truck engines with Active Fuel Management need it disabled in calibration or hardware. Set shift points and converter lockup for tire size and axle ratio, and confirm the speed signal first, because a wrong signal skews shifting and the speedometer.Medium3234

A standalone engine computer also works, but then the Jeep cluster needs an aftermarket replacement or an interface, the same choice Novak describes. Log with a wideband oxygen sensor, confirm knock control, and change ignition timing in small steps while watching for knock.Medium435

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 23 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

9 stages, in the order most builds follow.

  1. Pick the generation route and check the law
    Decide TJ or JK, gearbox and transfer case, and confirm what your state or country needs before buying parts.
  2. Buy the donor and controls together
    Get the engine with its harness, computer, pedal and sensors, plus the transmission you plan to keep.
  3. Strip the Jeep and inspect the frame
    Remove the old powertrain, check the frame at the mount areas and repair rust before welding.
  4. Fit mounts and set engine position
    Install the mount kit, set the engine where the maker specifies, and tack weld only after checking steering, firewall and hood clearance.
  5. Mate transmission and transfer case
    Fit the adapter, rear mount and crossmember, then cycle the suspension to check the oil pan and exhaust at full compression.
  6. Finish welding and measure driveshafts
    Weld the mounts, refinish the frame, and measure driveshafts with the Jeep on its springs.
  7. Install cooling, fuel and exhaust
    Fit the radiator, fan control, steam line, fuel pressure upgrade and headers, then leak-check fuel with the key on.
  8. Integrate the electrical systems
    Wire the engine computer, speed signals, tach or CAN interface and fused feeds, and confirm the cluster reads correctly.
  9. Calibrate, log and road test
    Load a calibration for the Jeep, log with a wideband, check shifting and speed, then complete break-in and inspections.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Tachometer stays at zero after the swapThe Jeep computer calculates engine speed from crank pulses and sends it to the cluster over the bus; a GM engine does not supply those pulses.Fit a crank position tach emulator such as Novak's E-TX (TJ and 2007-2010 JK) or switch to a GM-compatible aftermarket cluster.54
JK radiator fan never turns onThe Pentastar fan runs only on a PWM command, and 2007-2011 fans use a different (purple wire) control.Use a 2012-2018 Pentastar fan with a PWM controller fed by a GM-style temperature sensor.97
Low fuel pressure on a 1997-2004 TJThe factory module regulates about 40 psi (2.8 bar), below what a Gen III rail expects.Install a fuel integration kit that supplies about 58 psi (4.0 bar), and choose the version without a regulator if the rail already has one.6
Alternator hits the steering gearSome LS3 Camaro accessory drives place the alternator where the TJ steering gear sits.Use a C5 Corvette-style accessory drive or a third-party bracket.2
Rear driveshaft vibrates or the slip yoke pulls outThe longer V8 drivetrain shortens the rear shaft, and lift steepens the angle on the NP231 slip yoke.Fit a short-tail SYE kit and a fixed-yoke shaft measured on the springs; consider a double cardan shaft for very short rear shafts.161714
Transmission goes into limp mode after moving a JK to the NAG1The NAG1 takes wheel speed from the ABS module over CAN; one owner found an early JK ABS module did not supply it.That owner fitted a 2012-on ABS module. This is a single forum report from a Pentastar swap, so confirm with your kit maker.Low29

Frequently asked

Is there an LS swap kit for the Jeep JK?

Partly. Novak sells weld-in MMJK-G mounts for all 2007-2018 JKs, plus a radiator and fan controller. Complete kits with CAN integration came from Bruiser and RPM Extreme, but the Bruiser kit is listed as discontinued and RPM Extreme appears as a former vendor. Ask any current maker how the cluster, ABS and immobilizer are handled.Medium392427

What is the best LS swap kit for a Jeep TJ?

There is no single best kit, but the TJ has the most complete parts catalog. Novak sells weld-in and bolt-in mounts, transfer case adapters, a fuel upgrade, a radiator and a tach emulator, and Hooker brackets are sold through retailers. Choose mounts that suit your welding skill and whether the Jeep came with the inline six.Medium214620

What transmission should I use for a TJ LS swap?

Most builds use a GM 4L60E-family automatic with Novak's adapter to the NP231 or NP241OR. Manual TJs can keep the AX15 or NV3550 with a GM bellhousing adapter. Avoid the AX5, the 32RH, and the NSG370 six-speed, whose input rating of 272 lb-ft (369 N·m) sits below a 5.3 L's rated torque.141110134

Do you need a body lift for a TJ LS swap?

Usually not. Novak calls a required lift a myth for correctly placed engines, and Hooker lists its BHS513 TJ brackets as needing no body or suspension lift. Sagged springs or a deep oil pan can change that, so check pan-to-axle clearance at full compression before final welding.Medium420

Will the Jeep gauges work after an LS swap?

Only with extra parts. The 1996-on Jeep cluster takes a multiplexed signal from the Jeep computer, so you either keep that computer running with a tach emulator or CAN interface, or fit a GM-compatible aftermarket cluster. The speedometer still needs a signal from the transfer case sensor.45

Is an LS swapped Jeep Wrangler street legal?

It can be, but it is hard. In the US the engine generally must be the same model year or newer and keep its full emissions system, and California requires a BAR Referee inspection. Some JK kits were sold for off-road use only. Outside the US, expect registration, inspection or engineering approval.Medium37382442

Related

Sources

42 sources
  1. Engine Mounts: Jeep engine mount catalog (MMX series) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  2. GM LS/Vortec engine mounts for TJ/LJ Wranglers (MMTJ-G3 / MMTJ-G6) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  3. GM Gen III/IV V8 engine mounts for JK Wranglers (MMJK-G) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  4. Guide to GM engine swaps in the Jeep TJ and LJ · Novak Conversions · vendor-doc · retrieved 2026-10-27
  5. TJ/XJ/JK crank position tach emulator (E-TX / E-TXCC) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  6. Gen III+ fuel system integration kit for TJ and XJ (FSK-9704) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  7. JK Pentastar fan controller (E-PWM) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  8. TJ/LJ KryoFlow II radiators (GM Gen III-IV version) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  9. JK radiator for GM Gen III+ conversions (K-JK30H) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  10. GM engine to Jeep NV3550 adapter (kit 3504G) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  11. GM engine to Jeep AX15 adapter (GMAX15) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  12. GM engine to Jeep NSG370 adapter (kit 375) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  13. NSG370 six-speed transmission · Novak Conversions · vendor-doc · retrieved 2026-10-27
  14. GM 4L60E/4L65E/4L70E to Jeep NP transfer case adapter (4L61-23) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  15. GM 6L80 to Jeep transfer case adapters · Novak Conversions · vendor-doc · retrieved 2026-10-27
  16. NP231 transfer case · Novak Conversions · vendor-doc · retrieved 2026-10-27
  17. Driveshafts for Jeep conversions · Novak Conversions · vendor-doc · retrieved 2026-10-27
  18. Conversion JK headers for GM Gen III and IV engines (LSJK134P / LSJK134C) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  19. GM Generation III+ V8 engines · Novak Conversions · vendor-doc · retrieved 2026-10-27
  20. Hooker BHS513 engine mount brackets (TJ LS/LT swap), retailer listing · JBS Power Centre · vendor-doc · retrieved 2026-10-27
  21. Hooker Headers BHS522 LS or LT engine swap bracket kit for 87-95 Jeep Wrangler YJ · Quadratec · vendor-doc · retrieved 2026-10-27
  22. Advance Adapters 713088 Chevy LS1 V8 universal engine mounts: installation instructions (rev 03-09-16) · Advance Adapters (hosted by Low Range Off-Road) · vendor-doc · retrieved 2026-10-27
  23. Kooks Headers 37102200 1-3/4 in stainless headers for LS swap, 2007-2018 Jeep Wrangler JK 4-door (retailer listing) · LiftKits4Less · vendor-doc · retrieved 2026-10-27
  24. Bruiser Conversions Stage 1 complete JK LS engine installation kit (2007-450), discontinued listing · Northridge4x4 · vendor-doc · retrieved 2026-10-27
  25. SEMA 2012: Turn Key Expands Engine Kits to Late-model Vehicles · EngineLabs · press · retrieved 2026-10-27
  26. RpmExtreme official Gen4 LS swap thread, 2007-2011 JK (vendor posts) · JK-Forum · community · retrieved 2026-10-27
  27. RpmExtreme 2012+ LS conversion discussion (vendor posts) · JK-Forum · community · retrieved 2026-10-27
  28. JK LS swap: radiator fans work with JK sensor · JK-Forum · community · retrieved 2026-10-27
  29. JK Pentastar swap (page 9: ABS module and NAG1 limp mode) · JK-Forum · community · retrieved 2026-10-27
  30. Jeep Wrangler (TJ) · Wikipedia · reference · retrieved 2026-10-27
  31. Jeep Wrangler (JK) · Wikipedia · reference · retrieved 2026-10-27
  32. General Motors LS-based small-block engine · Wikipedia · reference · retrieved 2026-10-27
  33. LM7 5.3L Vortec 5300 Engine Specs · OnAllCylinders (Summit Racing) · press · retrieved 2026-10-27
  34. 4WD LS & LT Swap Compatibility Guide · PSI Conversion · vendor-doc · retrieved 2026-10-27
  35. LS3 EFI Crate Engine Specifications and Installation Instructions (19419889) · Chevrolet Performance (hosted by Speedway Motors) · oem · retrieved 2026-10-27
  36. Hemi swap security · Diag.net · community · retrieved 2026-10-27
  37. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  38. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-27
  39. Executive Order D-126-32: GM LS3 E-ROD engine kit · California Air Resources Board · standard · retrieved 2026-10-25
  40. Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-25
  41. StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  42. VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25