How it works
The controller times every spark and injection from the crank signal.
A sensor facing the wheel produces a pulse each time a tooth passes. Counting pulses gives angle; the time between them gives speed. Bosch describes the reference point as a missing element in the target wheel.1
In a 60-2 wheel, 60 equal positions are spaced 6 degrees apart and two consecutive teeth are removed, leaving 58. A 36-1 wheel has 36 positions 10 degrees apart with one removed. The long gap where teeth are missing is easy to detect and marks a fixed angle relative to top dead center.132
GM's LS V8 families use different patterns. Gen III engines use a 24x crank wheel with a 1x cam signal; most Gen IV engines use a 58x crank wheel with a 4x cam signal. The names count pulses per crank revolution.
The two systems need different sensors and controller software.Medium45
Two sensor types read the wheel. A variable reluctance (inductive) sensor generates an AC voltage that grows with speed and needs no power. A Hall-effect sensor is powered and gives a square wave even at very low speed.
Bosch lists air gaps of 0.3 to 1.8 mm for its inductive type and 0.2 to 1.8 mm for its Hall type.13
In tuning
The controller must know the angle between the missing-tooth gap and top dead center of cylinder one.
If that offset is wrong, every spark and injection event shifts by the same error. Confirm it with a timing light against a verified TDC mark after any trigger change.Medium62
More teeth give finer angle resolution and quicker sync, but also higher signal frequency. Bosch rates its IS-C inductive sensor to 15 kHz. A 60-2 wheel at 6,000 rpm produces 5,800 pulses per second, well inside that limit.3
Signal faults cause misfires, stalls and wrong timing. Check air gap, wheel runout, sensor polarity on inductive sensors, and shielding. A crank wheel alone cannot tell which half of the four-stroke cycle the engine is in; that needs cam sync.Medium316
Formula and worked example
f = n × N / 60
- f
- tooth pulse frequencyHz
- n
- teeth actually present on the wheel
- N
- engine speedrpm
Myths vs facts
Myth The missing tooth sits at top dead center.
Fact The gap sits at a fixed angle that the designer chooses, often well before TDC. The controller is told that offset.Medium62
Myth Any crank sensor works with any wheel.
Fact Sensor type, tooth size, air gap and the controller's decoder must all match the wheel. Bosch notes its data refers to a standardized wheel.3
Frequently asked
What does 60-2 mean on a trigger wheel?
60-2 means the wheel is laid out for 60 evenly spaced teeth, each 6 degrees apart, with two adjacent teeth removed. The 58 remaining teeth give angle and speed, and the gap where two are missing gives the controller a once-per-revolution reference. Bosch uses this pattern on many of its crankshaft sensor applications.13
What is the difference between 36-1 and 60-2?
A 36-1 wheel has teeth every 10 degrees with one missing; a 60-2 wheel has teeth every 6 degrees with two missing. The 60-2 wheel gives finer angle resolution between teeth. The 36-1 wheel has larger teeth that suit smaller diameter wheels. Both give one reference per revolution.Medium12
What is the difference between 24x and 58x on an LS engine?
24x and 58x are GM crank trigger patterns. Gen III LS engines use a 24x crank wheel with a 1x cam signal; most Gen IV engines use a 58x wheel with a 4x cam signal. Sensors, cam sensor location and controller software differ, so a Gen III controller needs a converter to run a 58x engine.Medium45
Hall effect or variable reluctance crank sensor: which is better?
Neither is universally better. Variable reluctance sensors are simple, unpowered and tolerate heat, and their output voltage rises with speed, so the controller input must handle small signals at cranking. Hall-effect sensors need power but give a clean square wave from zero speed and can detect direction. The controller input must match the sensor type.Medium13
Does a crank trigger wheel need a cam sensor?
For wasted-spark ignition and batch or semi-sequential injection, a crank wheel alone is enough. For sequential injection and coil-on-plug ignition, the controller also needs a cam signal, because the crank turns twice per engine cycle and its pattern repeats each revolution.62
Wiring, pinouts and parts
Used in these guides
- 1JZ-GTE Swap Nissan 240SX S14 (1995-98): Mounts, Transmission, Wiring and Legal Guide
- 2JZ Swap BMW E46 3 Series (1999-2006): 2JZ-GTE and 2JZ-GE Guide
- 2JZ Swap Nissan 240SX S13 (1989-94): 2JZ-GTE and 2JZ-GE Guide
- Early Bronco Coyote Swap (1966-77): Mounts, 6R80 and Dana 20 Adapters, Fuel, Ford Performance Control Pack and Legal Guide
- Coyote Swap Dentside F-100 / F-150 (1973-79): Mounts, Fuel, Wiring and Legal Guide
- Coyote Swap Fox Body Mustang (1979-93): Mounts, Fuel, Wiring and Legal Guide
- Coyote Swap SN95 and New Edge Mustang (1994-2004): Controls, K-Member, Fuel and Legal Guide
- Hemi Swap Jeep JK (2007-18): 5.7 and 6.4 Conversion Guide
- Hemi Swap Jeep Wrangler TJ (1997-2006): Mounts, Transmission, Transfer Case and Legal Guide
- K-Swap Acura Integra DC2 (1994-2001): K20 and K24 Swap Guide
- CRX K Swap and Civic EF (1988-91): K20 and K24 Swap Guide
- K Swap EG Civic (1992-95): K20 and K24 Swap Guide
- K Swap EK Civic (1996-2000): K20 and K24 Swap Guide
- K-Swap Mazda Miata NA (1990-97): K24 and K20 Swap Guide
- E30 LS Swap: Mount Kits, Oil Pan, T56 or ZF, Differential, Brakes and Legal Guide
- LS Swap BMW E36: Mounts, Headers, Steering Shaft, Wiring and Legal Guide
- LS Swap BMW E46: Mounts, CAN Bus Cluster, Subframe and Legal Guide
- 3rd Gen Camaro LS Swap (1982-92): Mounts, K-Member, Oil Pan, Torque Arm, T56 and Fuel Guide
- C4 Corvette LS Swap (1984-96): Mounts, 4+3 vs ZF6 vs 4L60E, Digital Dash, VATS, ABS and Legal Guide
- G-Body LS Swap (1978-88): Mounts, Crossmember, Oil Pan, Steering Box, 7.5 in Rear and EFI Fuel Guide
- OBS LS Swap (1988-1998 C/K, Tahoe, Yukon, Suburban): Mounts, 4L60E/4L80E, Fuel, Gauges, ABS and Legal Guide
- S10 LS Swap (1982-2004): Mounts, Headers, Crossmembers, Oil Pan, Steering Shaft and Legal Guide
- 240Z LS Swap: Mounts, Crossmember Kits, T56, R200 Diff, Chassis and EFI Fuel Guide
- Fox Body LS Swap (1979-93): K-Members, Mounts, Oil Pan, T56 and TKX, Fuel, Ford Cluster Wiring and Legal Guide
- Ford Ranger LS Swap (1983-2011): Mounts, Oil Pan, Transmission, PATS, Speedometer, Fuel and Legal Guide
- G35 LS Swap (V35, 2003-2007): Sedan and Coupe Kits, CD009 or T56, Driveshaft, CAN Gauges, Automatics and Legal Guide
- Jeep Cherokee XJ LS Swap (1984-2001): Unibody Mounts, Low-Hood Intake, AW4 Replacement, NP231/NP242 Adapters, Fuel and Legal Guide
- Jeep Wrangler LS Swap (TJ 1997-2006 and JK 2007-2018): Mounts, Transfer Case Adapters, Fuel, CAN Bus Integration and Legal Guide
- LS Swap NA Miata: Subframe, Differential, Transmission, Wiring and Legal Guide
- LS Swap RX-7 (FD): Subframe, Steering, Differential, Wiring and Legal Guide
- RX-8 LS Swap (SE3P, 2004-2011 US): Mounts, PPF Delete, Steering Rack, Differential, CAN Gauges and Legal Guide
- LS Swap 240SX (S13): Engines, Kits, Transmission, Wiring and Legal Guide
- 300ZX LS Swap (Z32, 1990-1996): Mounts, Z32 5-Speed or T56, HICAS, Gauges, Differential and Legal Guide
- 350Z LS Swap (Z33): Engines, Mounts, CD009 or T56, Wiring, Gauges and Legal Guide
- 944 LS Swap (1982-91): Kits, Transaxle, Clutch Adapter, Oil Pan and Legal Guide
- Subaru BRZ / Scion FR-S / Toyota 86 LS Swap (2013-2020): Mounts, Gearbox, CAN Bus, Wiring and Legal Guide
- Tacoma LS Swap (1995-2004): Mounts, 4x4 Transfer Case Adapters, Transmissions, Oil Pan and Legal Guide
- Volvo 240 LS Swap (1975-93): Mounts, Oil Pan, T56, Two-Piece Driveshaft, Rear Axle, Fuel and Legal Guide
- LS Swap C10 Square Body (1973-87): LS and LT Swap Guide
- RB25DET Swap Nissan 240SX S13 (1989-94): Mounts, Wiring and Legal Guide
- RB26DETT Swap Nissan 240SX S14 (1995-98): RWD Conversion, Mounts, Gearbox and Import Guide
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- Crankshaft speed sensor product data sheet · Robert Bosch GmbH · vendor-doc · retrieved 2026-10-25
- Crankshaft position sensor · Wikipedia · reference · retrieved 2026-10-25
- Inductive Speed Sensor IS-C data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-25
- Engine swapping a Gen IV in place of a Gen III · LSX Magazine · press · retrieved 2026-10-25
- Dialing in LS sensors for various generations · EngineLabs · press · retrieved 2026-10-25
- Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-25

