Volvo 240 LS Swap (1975-93): Mounts, Oil Pan, T56, Two-Piece Driveshaft, Rear Axle, Fuel and Legal Guide

An LS swap into a Volvo 240 is a known but fabrication-heavy conversion: few bolt-in parts are sold, and builders typically make or adapt mounts, the transmission crossmember and exhaust. It needs a GM-pattern transmission, a new driveshaft in place of the two-piece factory shaft, LS fuel pressure and a stronger rear axle. The main hurdles are mount fitment, the factory axle and wiring.Medium12469

Difficulty4/5 · HardMedium12847
  • Bolt-in LS mount kits are scarce, and the ICT Billet kit whose name lists the 240 shows fitment for the 940 only.
  • The factory two-piece driveshaft needs a slip yoke modification or a new one-piece shaft, which may need floor work on lowered cars.
  • The 240 was built around four-cylinder and V6 engines, and press-featured LS cars replaced the rear axle.
  • The fuel system pairs an in-tank pre-pump with an external main pump that was not designed for LS pressure.
  • Every engine and transmission signal to the Volvo cluster has to be adapted.

At a glance

The key numbers and parts, with the source on each tile.

Factory enginesRed block four-cylinders (B21, B23, B230), PRV V6 and dieselsSourced · medium8
Curb weight2,840 lb for a 1989 US-spec 240, fully fueled1,288 kgSourced · medium8
Front suspension and steeringMacPherson struts with rack-and-pinion steeringSourced · medium8
Mount route
  • Custom or adapted mounts
  • Verify any kit's listed fitment before buying
ICT Billet's EM-LS-VLV1 is named for the 240 but its product page lists 1991-98 940 fitment.Sourced · medium1
TransmissionGM T56 manual is the press-documented choiceSourced · medium46
Driveshaft
  • Factory shaft is two-piece
  • Modify with a slip yoke or replace with a one-piece shaft
Sourced · medium2
Rear axle

Documented LS cars run a narrowed Explorer 8.8, a Ford 9-inch or a Chrysler axle

Sourced · medium456
Fuel
  • Return system at about 58 psi4.0 bar
  • Pump flowing 45 gph at pressure for GM's LS3170 L/h
Sourced912
California route

Every 240 predates 1996, so GM's E-ROD LS3 executive order can apply, followed by a BAR Referee inspection

Sourced2119

Recommended engines

  • LS1 · Aluminum engine that keeps weight off the 240's nose; a press-featured 1975 242 ran an LS1 with a T56 and a 1999 Camaro computer.
  • 5.3 LM7 / L59 / LY5 (Gen III/IV truck) · The cheapest Gen III donor with a 24x trigger and no Active Fuel Management; its truck pan and accessory drive need checking against the Volvo crossmember and core support.
  • 6.0 LQ4 / LQ9 / LY6 / L96 (truck) · Iron 6.0 L truck and van engines are cheap and common; one press-featured 240 runs a supercharged Gen IV 6.0 pulled from a van, behind a Camaro T56.
  • LS3 / L99 · New Gen IV crate engine with GM installation data and a matching controller kit; it suits builders who want documented fuel and electrical requirements from the start.

Mounts

An LS swap Volvo 240 project does not have the bolt-in kit ecosystem of a Fox Mustang or an S13.

ICT Billet EM-LS-VLV1

Upper and lower engine mounts with polyurethane bushings and hardware

The URL and title name the 1974-93 240, but the fitment list shows 1991-98 940 only. Confirm with the maker.Sourced · medium1
Kaplhenke Racing / BNE Dynamics
  • Sells 240 driveline and suspension parts such as a Ford T5/TKO/TKX adapter plate for the red block and adjustable torque rods
  • We found no LS mount kit in its catalog
Sourced · medium23

ICT Billet sells EM-LS-VLV1, upper and lower LS mounts with polyurethane bushings, but its page names the 240 in the title while listing only the 1991-98 940 as fitment.Medium1

Confirm that kit's fit for your car in writing before ordering. Otherwise, plan weld-in or fabricated mounts, a new transmission crossmember and engine placement worked out on the car, which is how most documented 240 V8 builds were done.Low14

Kaplhenke Racing, now trading as BNE Dynamics, is a well-known 240 parts maker, but its V8-related plate adapts Ford T5 and TKO gearboxes to the Volvo red block, not to an LS. Do not buy it expecting an LS bellhousing solution.Medium2

Transmission

None of the Volvo gearboxes bolt to an LS, so the swap brings a GM-pattern transmission.

Factory transmissions
  • M45, M46 (with overdrive) and M47 manuals
  • BW35, BW55, AW55, AW70 and AW71 automatics
Sourced · medium8
Documented LS gearboxGM T56 from a Camaro, in two press-featured 240 buildsSourced · medium46
Factory driveshaftTwo-pieceSourced · medium2

The T56 is the press-documented choice in LS 240s, and GM automatics such as the 4L60E work if you add a controller and an output speed signal.Medium84617

The 240 uses a two-piece driveshaft. BNE describes two routes for V8 cars: modify the factory shaft with a slip yoke, or fit a new one-piece shaft, which may need floor pan work on lowered cars. Measure only after the engine and transmission sit on final mounts.Medium2

A one-piece shaft makes pinion angle critical. BNE's adjustable torque rods let you set axle position and pinion angle, and the company calls that adjustment critically important when a one-piece shaft goes in.Medium3

Clearance

The engine sits between MacPherson strut towers above a front crossmember and rack-and-pinion steering.

Oil pan
  • No published 240 LS pan fitment found
  • Plan a test fit against the front crossmember and rack
Low confidence81
Power steering

One track-driven LS 240 needed a new pump, a power steering cooler and new lines

Sourced · medium4

Neither ICT nor any press build we found publishes pan or rack clearance for a 240, so mock up with the pan you intend to run and check it at full suspension compression.Low81

Plan the power steering early. The 1983 240 featured by LSX Magazine lost its pump on a road course, and the fix included a new pump, a power steering cooler and new lines. Route hoses away from the headers.Medium4

Check the brake master cylinder, steering shaft and firewall against the driver-side head and header before finalizing engine position. A V8 is far wider than the in-line four it replaces.Low8

Cooling

The 240's cooling system was sized for a four-cylinder or V6.

GM guidance

Retrofits may need cooling, fuel, electrical and exhaust changes not included with the engine

Sourced12
Documented next steps

One LS 240 owner planned an upgraded cooling system and oil coolers after track use

Sourced · medium4

Fit an aluminum radiator with electric fans and a shroud, and expect to make mounts at the core support. GM warns that retrofits often need cooling changes.Medium128

Track use exposes marginal cooling quickly. The LSX-featured 240 owner listed an upgraded cooling system and oil coolers for the next revision after events, so leave space for an oil cooler if the car will see laps.Medium4

Route the steam vent lines to the top of the system and bleed carefully. Let the engine computer switch the fans through relays, and add a transmission cooler for an automatic.Low12

Fuel

Later 240s pair an in-tank pre-pump with an external main pump on a bracket under the car beside the filter.

Factory layout (from 1985)

In-tank pre-pump feeding an external main pump mounted under the car with the filter

Sourced · medium7
LS pressure
  • About 58 psi typical4.0 bar
  • GM states 58-60 psi for its LS3400 kPa
Sourced912
Pump flow (GM LS3)At least 45 gph at the recommended pressure170 L/hSourced12

That system fed a four-cylinder, so check any pump against LS flow at about 58 psi before reusing it.Medium79

PSI Conversion prefers an in-tank pump over a frame-mounted one, with a return-style regulator near the rail and 6AN feed and return lines. Fitting a single high-flow in-tank pump and deleting the external pump is one way to meet that.Medium9

Exhaust

We found no off-the-shelf 240 LS headers, so expect custom headers or modified manifolds and a fabricated system.

Documented exhaust

Custom stainless system, TIG-welded, on the LSX-featured 1983 240

Sourced · medium4

The press-featured 1983 240 used a custom TIG-welded stainless exhaust.Low4

Route primaries clear of the steering shaft, rack and power steering lines, and keep the system away from fuel lines under the floor. Put the wideband oxygen sensor bung in the collector or downpipe, away from slip-joint leaks.Low414

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads

The Volvo engine computer and its harness come out; the LS needs its own computer, harness, pedal and sensors for its generation.

Crank and cam triggers
  • Gen III: 24x crank, rear cam sensor
  • Gen IV: 58x crank, front-cover cam sensor
Sourced · medium14
Factory injection
  • Bosch Jetronic family
  • LH-Jetronic on the B230F from 1985
Sourced · medium8
Signal interface

Dakota Digital SGI-100BT rescales speed signals 25-400 percent and tach signals for 1-16 cylinders, 5 V or 12 V

Sourced · medium10

Choose a GM controller kit, a re-calibrated donor GM computer or a standalone ECU.Medium81314

The cluster needs a tach signal it can read. Autometer notes that calibration changes removing GM features can weaken the tach output, and a pull-up resistor often fixes it. An interface such as the SGI-100BT can also set the cylinder count and signal voltage.Medium1110

Check how your year's speedometer is driven before choosing a speed source, then feed the GM computer and cluster from one calibrated signal. Wire fuel pump and fan relays, a check-engine lamp and gauge senders. Safety: fuse every new feed at the battery.Low1013

Chassis

The factory axle was built behind four-cylinder and V6 engines, and every press-featured LS 240 we found replaced it.

Documented rear axles
  • Narrowed 31-spline Explorer 8.8 with TruTrac
  • Ford 9-inch on a four-link
  • Chrysler rear end
Sourced · medium456
Documented brakes

Volvo S60R calipers with 330 mm rotors in front, Wilwood 13 in (330 mm) rears

Sourced · medium4

Builds used a narrowed Ford Explorer 8.8 with a limited slip, a Ford 9-inch on a four-link, or a Chrysler axle. Plan the axle as part of the swap budget.Medium8456

Rear suspension changes follow the axle. The LSX-featured 240 needed an adjustable panhard bar, custom lower links and shock mounts frenched into the unibody, and adjustable torque rods help set pinion angle.Medium43

Upgrade brakes before chasing speed; the documented car moved to larger front calipers and rotors and Wilwood rears. We found no measured corner weights for an LS 240, so weigh the car after the swap.Low4

Tuning

A GM controller kit carries a calibration matched to its crate engine.

Active Fuel Management
  • Most Gen IV 5.3 L truck engines have AFM
  • The Gen III LM7 does not
Sourced · medium1615
Break-in (GM crate)

Avoid maximum engine speed and long high-load periods for the first 500 miles (12 to 15 engine hours)

Sourced12

A donor computer or standalone ECU needs settings for the actual injectors, airflow, transmission, tire size and axle ratio, and Gen IV engines with Active Fuel Management need it disabled.Medium1316

Log with a wideband oxygen sensor, confirm knock control works and set a sensible rev limiter before loaded pulls. Change ignition timing in small, monitored steps, and verify speed readings before setting shift points on an automatic.Low1412

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 23 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Check the law and plan the package
    Confirm your emissions route, then choose engine, transmission, rear axle and engine computer together.
  2. Confirm mount fitment
    Get written fitment from any kit maker, or plan weld-in mounts and a crossmember.
  3. Strip the car
    Disconnect the battery, relieve fuel pressure, and remove the engine, gearbox, driveshaft and engine harness.
  4. Mock up the engine
    Set engine height and position, test-fit the pan against the crossmember and rack, and check the firewall, master cylinder and steering shaft.
  5. Mount the transmission
    Build or fit the crossmember and set the driveline angle.
  6. Rear axle and driveshaft
    Install the new axle and links, set pinion angle, then measure for the driveshaft.
  7. Fuel and cooling
    Fit the pump, regulator and lines at LS pressure, then the radiator, fans, steam vents and coolers.
  8. Exhaust and steering
    Fabricate headers and exhaust around the steering, then plumb the power steering with a cooler.
  9. Wire it
    Install the harness and computer, feed the Volvo tach and speedometer, and fuse every circuit.
  10. First start and calibration
    Pressure-test fuel, bleed cooling, start and check for leaks, then log with a wideband and calibrate before load.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Mount kit does not fit when it arrivesListing names the 240 but the maker's fitment data shows a different chassisGet written fitment for your year before ordering, or plan weld-in mounts.Medium1
Bought a Kaplhenke/BNE T5 plate expecting it to fit the LSThe plate adapts Ford T5 and TKO gearboxes to the Volvo red blockUse a GM-pattern transmission or an LS-specific bellhousing for the swap.Medium2
Driveline vibration after fitting a one-piece shaftPinion angle set for the factory two-piece shaftFit adjustable torque rods and set axle position and pinion angle to suit the new shaft.Medium32
Power steering failure on trackFluid overheating and a stressed pumpReplace the pump, add a power steering cooler and new lines, and bleed the system properly.Medium4
Tachometer dead or erraticWeak tach output after calibration changes or wrong interface settingsAdd a pull-up resistor to switched power, or use a signal interface set for eight cylinders and the cluster's voltage.Medium1110
Lean condition or stumble at high loadFactory Volvo pre-pump and main pump sized for a four-cylinderFit a pump that flows at least 45 gph (170 L/h) at LS pressure, ideally in the tank, and verify rail pressure under load.Medium7912

Frequently asked

Is there an LS swap kit for the Volvo 240?

Not a complete one that we could verify. ICT Billet sells LS mounts under a 240 name, but the product page lists only 1991-98 940 fitment, so confirm before buying. Kaplhenke Racing (BNE Dynamics) makes 240 parts, but its V8-related plate suits Ford gearboxes on the Volvo engine. Most LS 240s use fabricated mounts.Medium12

Will the Volvo 240 rear end hold an LS?

Builders do not rely on it. The 240 was built for four-cylinder and V6 engines, and every press-featured LS 240 we found replaced the axle: one with a narrowed Explorer 8.8 and limited slip, one with a Ford 9-inch on a four-link, and one with a Chrysler axle. Budget for the axle and its links.Medium8456

What transmission do you use for an LS swap Volvo 240?

Usually a GM T56 six-speed, which two press-featured 240 builds used. No Volvo gearbox bolts to an LS. GM automatics such as the 4L60E also work with a controller and speed signal. Budget a crossmember and a new or modified driveshaft, because the factory shaft is two-piece.Medium46172

Do I need a new driveshaft for an LS swap Volvo 240?

Yes, in practice. The factory shaft is two-piece, so you either modify it with a slip yoke or fit a new one-piece shaft. A one-piece shaft can need floor pan work on lowered cars, and adjustable torque rods help set pinion angle, which BNE calls critical with a one-piece shaft.Medium23

What fuel pump do I need for an LS Volvo 240?

One that flows enough at about 58 psi (4.0 bar). GM asks for 45 gph (170 L/h) at pressure for its LS3. Later 240s use an in-tank pre-pump plus an external main pump built for a four-cylinder, and PSI Conversion prefers a single in-tank pump with a return-style regulator near the rail.Medium1279

Is an LS swapped Volvo 240 street legal?

It can be. In California, every 240 predates 1996, so GM's E-ROD LS3 package under its executive order, followed by a BAR Referee inspection, is a documented route within its test-weight limit. Elsewhere rules vary by country and state. This is general information, not legal advice; check with your authority first.Medium211918

Related

Sources

24 sources
  1. Volvo LS Swap Engine Mount Kit, LS1 / LS3 (EM-LS-VLV1) · ICT Billet · vendor-doc · retrieved 2026-10-27
  2. Dual Pattern Ford T5 / TKO / TKX Adapter Plate V3 · BNE Dynamics (Kaplhenke Racing LLC) · vendor-doc · retrieved 2026-10-27
  3. 240 Adjustable Torque Rods · BNE Dynamics (Kaplhenke Racing LLC) · vendor-doc · retrieved 2026-10-27
  4. Meet Sean Fogli and his LS-Swapped 1983 Volvo 240 · LSX Magazine · press · retrieved 2026-10-27
  5. This Turbo LS Volvo Wagon Runs Eights And Hits 170 MPH · LSX Magazine · press · retrieved 2026-10-27
  6. eBay Find: Here's Your Chance To Own A Pro-Touring LS1 Volvo! · LSX Magazine · press · retrieved 2026-10-27
  7. Volvo Fuel Pump Kit, Bosch 9142044KT (pre-pump and main pump) · FCP Euro · vendor-doc · retrieved 2026-10-27
  8. Volvo 200 Series · Wikipedia · reference · retrieved 2026-10-27
  9. LS and LT Swap Fuel System Guide · PSI Conversion · vendor-doc · retrieved 2026-10-27
  10. Dakota Digital SGI-100BT speed and tach signal interface (product page) · PSI Conversion · vendor-doc · retrieved 2026-10-27
  11. Tachometer does not work with my LS engine swap application. Why? · Auto Meter · vendor-doc · retrieved 2026-10-27
  12. LS3 EFI Crate Engine Specifications and Installation Instructions (19419889) · Chevrolet Performance (hosted by Speedway Motors) · oem · retrieved 2026-10-27
  13. Chevrolet Performance 58x/ETC engine controller kit installation instructions · GM / Chevrolet Performance (hosted by JEGS) · oem · retrieved 2026-10-25
  14. Dialing In LS Sensors For Various Generations · EngineLabs · press · retrieved 2026-10-27
  15. LM7 5.3L Vortec 5300 Engine Specs · OnAllCylinders (Summit Racing) · press · retrieved 2026-10-27
  16. General Motors LS-based small-block engine · Wikipedia · reference · retrieved 2026-10-27
  17. GM 4L60-E transmission · Wikipedia · reference · retrieved 2026-10-27
  18. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act · U.S. Environmental Protection Agency · standard · retrieved 2026-10-25
  19. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-27
  20. Smog Inspections · California Department of Motor Vehicles · standard · retrieved 2026-10-27
  21. Executive Order D-126-32: GM LS3 E-ROD engine kit · California Air Resources Board · standard · retrieved 2026-10-25
  22. Change vehicle details on a V5C registration certificate (log book) · GOV.UK (DVLA) · standard · retrieved 2026-10-25
  23. § 19 StVZO: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  24. Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government Department of Infrastructure, Transport, Regional Development, Communications and the Arts · standard · retrieved 2026-10-25