LS Swap 240SX (S13): Engines, Kits, Transmission, Wiring and Legal Guide

An LS swap 240SX is one of the most common V8 conversions for the S13, backed by bolt-in mount, oil pan, driveshaft and header kits. The work centers on fitting a T56 into a narrow tunnel, building the exhaust and fuel system, and wiring the GM engine into Nissan gauges. The stock rear differential and axles become the weak link.Medium124

Difficulty3/5 · ModerateMedium1234
  • Mature kit ecosystem: engine and transmission mounts, a modified baffled oil pan, oil filter relocation and a driveshaft are sold as a set.
  • The T56 needs the transmission tunnel reshaped, and the engine bay is tight enough that builders report removing the drivetrain more than once.
  • No bolt-on exhaust exists; plan on custom pipework around the steering column.
  • Gauges, fuel pump control, fans and the throttle pedal all need integration work.
  • The stock differential and axles were designed for a four-cylinder and need an upgrade plan.

At a glance

The key numbers and parts, with the source on each tile.

Stock engine
  • KA24DE 2.4 L DOHC (1991-94), 155 hp at 5,600 rpm and 160 lb-ft217 N·m
  • 1989-90 cars used the SOHC KA24E
Sourced · medium5
Stock curb weight (S13)About 2,698 lb1,224 kgWe found no sourced figure for the net weight change after an LS swap.Sourced · medium5
Most common engines

LS1, junkyard 5.3 L truck engines, and LS3 crate or E-ROD engines

Most kits are designed around the LS1.Sourced · medium41
Transmission
  • Tremec T56 is the usual choice
  • The Nissan CD009 is an alternative with a weld-in tunnel clearance kit
Sourced · medium14
Mount approach
  • Bolt-in engine and transmission mount kit
  • Typical kits add a modified baffled pan, remote oil filter and driveshaft
Sourced · medium1
Oil pan
  • Swap-specific front-sump pan and pickup
  • The stock GM dipstick hole is plugged and the windage baffle trimmed
Sourced · medium24
Weak points after the swapRear differential, axles and the clutch master cylinderSourced · medium41
California route

1989-94 S13s predate 1996, so a GM E-ROD LS3 package under CARB EO D-126-32 is an option for vehicles up to 4,500 lb test weight

Sourced · medium109

Recommended engines

  • LS1 · Most S-chassis mount kits, pans and headers were developed around the aluminum-block LS1 with a T56, so parts fit with the fewest surprises.
  • 5.3 LM7 / L59 / LY5 (Gen III/IV truck) · The cheapest and most plentiful junkyard LS; the iron block adds weight over the nose compared with aluminum-block engines.
  • LS3 / L99 · Available new as a crate engine and as the E-ROD emissions package, which is the documented route to a California-legal swap in a pre-1996 S13.
  • LS2 · Aluminum 6.0 L Gen IV engine; uses the 58x crank trigger and front cam sensor, so wiring follows the LS3 pattern rather than the LS1.

Mounts

For an LS swap 240SX builders almost always buy a mount kit rather than fabricate.

Typical kit contents

Engine mounts, transmission mount, modified and baffled oil pan, oil filter relocation, driveshaft

Sourced · medium1
S13 vs S14
  • Some mount designs use a pivoting pedestal to cover the width and angle differences between the S13 and S14 subframes
  • Others are sold per chassis
Sourced · medium4

The kits locate the engine on the factory front crossmember and pair it with a matching transmission mount, so the driveline angle is set for you.Medium14

Check exhaust manifold fit against the mounts before final assembly. One builder using stock LS3 manifolds had to grind the driver-side billet mount for clearance, because kit makers cannot test every manifold.Medium2

The S14 (1995-98) uses the same basic layout, but confirm the kit lists your chassis. Some kits ship S13 and S14 variants, while others use adjustable pedestals that suit both.Medium4

Transmission

The T56 is the default gearbox for this swap.

Preferred gearbox

T56, because its shifter lands close to the stock Nissan shifter opening

Sourced · medium1
Shifter position
  • The T56 shifter sits about 2 in forward of stock51 mm
  • A relocating short shifter clears the dash in 1st, 3rd and 5th
Sourced · medium1

The later TR6060-style Magnum housing is shorter, and one builder found no good shifter extension to bring its lever back to the Nissan opening.Medium1

The stock clutch master cylinder is not sized for the larger LS clutch and T56 slave. Swap kits replace it with a larger master cylinder or adapter, and builders replace the clutch while the engine is out because removal is so difficult.Medium14

The Nissan CD009 from the 350Z and 370Z is another option, but it needs a weld-in tunnel clearance kit. Automatic builds using GM automatics also exist through dedicated mount kits.Medium4

Clearance

The tunnel is the main clearance job.

Transmission tunnel
  • Must be reshaped for a T56 with a stock bellhousing
  • A compact aftermarket bellhousing reduced the need in one build
Sourced · medium21
Accessory drive

The Cadillac CTS-V accessory layout is the most compact and fit the S13 without clearance issues in one documented build

Sourced · medium1

One builder had to pull the engine and transmission twice because the tunnel had not been reshaped enough the first time.Medium2

Lowering the engine from above is a tight fit. The same builder found that dropping the subframe and raising the body over the drivetrain was quicker on the second attempt.Medium2

Watch the hood line. The power steering reservoir in its stock LS location hit the hood and was relocated to the strut tower, and a compact starter helps header clearance.Medium21

Cooling

Budget for a larger radiator and electric fans.

Radiator
  • Stock KA24DE radiator is not adequate
  • A thicker aluminum KA-pattern radiator keeps both hose necks on the passenger side
Sourced · medium1
Steam vent

The LS head steam port must be plumbed back into the cooling system, often via a bung welded to the radiator top tank

Sourced · medium2

Choosing a KA-style core puts both inlet and outlet on the passenger side, which made hose routing to the LS straightforward in one build.Medium1

Do not cap the LS steam port. It bleeds trapped air from the heads, so route it to a high point such as a welded bung on the radiator tank, using hose rated for engine-bay heat.Medium2

Heater hoses need adapters to reach the Nissan core. Several builders report that the S13 heater valve can stop coolant flow entirely, and some add a bypass so the LS always has flow through that loop.Low21

Fuel

The KA24DE pump will not support an LS.

PumpUpgraded in-tank pump on the factory hanger is standard practiceSourced · medium1
Regulator (California build)
  • An adjustable regulator was rejected at a California referee inspection
  • The build switched to a C5 Corvette OEM filter-regulator near the tank
Sourced · medium2

Fit a higher-flow in-tank pump, a correctly sized filter and a regulator, then adapt the factory hard lines to AN or GM quick-connect fittings at the rail.Medium12

A rear-mounted OEM filter-regulator creates a returnless system and removes the return line from the engine bay. Use the fuel pump flow calculator to check pump capacity against your power target.Medium2

Exhaust

Headers are sold separately from most mount kits.

Off-the-shelf exhaust
  • None bolt-on
  • The system is custom-fabricated
Sourced · medium1
Documented layout

2 in (51 mm) pipe past the steering column, merging into a 3 in (76 mm) single system

Sourced · medium3

Builds using GM manifolds and catalysts for emissions compliance found the driver side especially tight around the steering column.Medium13

Plan the system so each section can come off without dropping the drivetrain. V-band joints keep the profile low and need no gaskets.Medium3

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads

The engine computer must read the crank trigger and cam sync for its generation.

Crank and cam triggers
  • Gen III (LS1, early 5.3): 24x crank wheel and rear-mounted cam sensor
  • Gen IV (LS2, LS3, later 5.3): 58x crank wheel and front-cover cam sensor
Sourced · medium7
Throttle
  • The LS3 is drive-by-wire
  • Its matching pedal needs a custom bracket on the Nissan pedal mounting points
Sourced · medium31

Gen III and Gen IV sensors differ in tooth count and supply voltage, so match the sensors, harness and computer to the engine.Medium7

Plan for eight injectors, eight coil-on-plug coils, a mass airflow sensor and oxygen sensors. Drive-by-wire engines need the matching pedal and throttle body; cable-throttle LS1 setups keep a cable. Engines with Active Fuel Management need it disabled in calibration or hardware.Medium136

Inside the car, feed the Nissan cluster a tach signal, speed, check-engine lamp and coolant temperature. One build fitted the Nissan temp sender into a plugged coolant port at the rear of the block; the fuel pump trigger and two fan outputs connect through relays. A/C needs pressure-switch and compressor-request wiring.Medium34

Chassis

Swap guides warn that a high-output V8 pushes the S13 differential and axles beyond their design limits.

Factory LSD availability
  • US S13 hatchbacks got an LSD only with the optional sports package from 1991
  • Many cars are open-differential
Sourced · medium5
S14 hubs
  • S14 SE and LE models use 5-lug hubs
  • Base cars are 4-lug
Sourced · medium5

Treat a stronger differential, axles and an LSD as part of the swap budget, not an afterthought.Medium4

Start with a straight, rust-free shell. One builder recommends rejecting a bent or rotten car outright, since the chassis was designed around a four-cylinder engine.Medium2

Swap-specific front sway bars exist because the stock bar location can conflict with the LS pan and headers. Check bar clearance when you test-fit the engine.Medium4

Tuning

A complete GM controller kit is the lowest-risk path because the calibration already matches the engine.

GM controller kit contents

GM offers the LS3 E-ROD with a matched engine computer, harness, drive-by-wire pedal and oxygen sensors

Sourced · medium1
GM LS3 ratingGM rates the LS3 at 430 hp and 424 lb-ft575 N·mSourced · medium1

A junkyard engine with a reflashed donor computer or a standalone ECU gives more freedom but needs a full calibration, starting with fuel delivery and idle.Medium1

Log with a wideband oxygen sensor before any loaded pulls, confirm knock control is active, and set a conservative rev limiter. Ignition timing changes should be made in small steps with knock monitoring, never copied from another car.Low1

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 26 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Check the chassis and the law
    Inspect the shell for rust and damage, and confirm what your state or country requires before buying parts.
  2. Pick the engine generation
    Choose Gen III or Gen IV, then buy the matching harness, sensors and engine computer so triggers and throttle type agree.
  3. Prepare the engine on a stand
    Fit the swap oil pan and pickup, plug the dipstick hole, and install the clutch, flywheel, starter and compact accessory drive.
  4. Remove the KA24DE and prepare the tunnel
    Pull the engine and gearbox, then reshape the transmission tunnel for the T56 before the first test fit.
  5. Install engine and transmission
    Raise the body over the drivetrain or lower it with a hoist, using helpers. Fit the clutch master conversion and power steering lines while access is good.
  6. Build cooling and fuel systems
    Mount the radiator and fans, plumb the steam port and heater, then install the pump, filter, regulator and rail lines.
  7. Fabricate the exhaust
    Fit headers or manifolds, route pipe past the steering column, and add catalysts and hangers.
  8. Wire the engine and gauges
    Mount the engine computer, run fused power and grounds, connect fuel pump and fan relays, the pedal and the cluster signals.
  9. First start and leak check
    Prime oil and fuel, verify no leaks, confirm trigger sync and coolant flow, then bleed the cooling system.
  10. Calibrate and shake down
    Log with a wideband, verify knock control and temperatures, then build up load gradually before any road or track use.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Engine and gearbox will not drop into placeThe transmission tunnel has not been reshaped enough for the T56 case.Remove the drivetrain, rework the tunnel further, or fit a compact bellhousing; drop the subframe and lower the body to speed up fitting.Medium21
Shifter hits the radio and dash trim in 1st, 3rd and 5thThe T56 shift lever sits about 2 in (51 mm) ahead of the Nissan opening.Fit a short shifter that relocates the lever rearward.Medium1
Clutch does not fully releaseThe stock S13 master cylinder cannot move enough fluid for the LS clutch and T56 slave.Install a clutch master cylinder conversion matched to the T56 hydraulics.Medium41
Engine runs hot or gauge reads wrongSteam port capped, heater valve blocking flow, undersized radiator, or the Nissan sender not fitted to the block.Plumb the steam port, keep coolant flow through the heater loop, use a larger radiator, and install the Nissan sender in an adapted block port.Low231
Fails California Referee inspectionNon-OEM or adjustable emissions-related parts, such as an adjustable fuel pressure regulator.Run the complete E-ROD package as supplied, use OEM-style fuel regulation and keep the evaporative canister connected.Medium210
Broken axles or differentialFour-cylinder-era driveline components under V8 torque.Upgrade the differential, LSD and axles as part of the swap.Medium4

Frequently asked

How much does an LS swap 240SX cost?

Expect five figures for a complete, reliable car. One documented S13 build with a new LS3 crate engine, mount kit, T56 and supporting parts came to around $15,000 USD. A junkyard 5.3 L lowers the engine cost, but mounts, transmission, clutch, fuel, cooling, exhaust and wiring still add up, and the rear differential often needs upgrading too.Low31

What transmission is best for a 240SX LS swap?

The Tremec T56 is the most common choice because its shifter sits close to the stock Nissan opening and kits are designed around it. Expect to reshape the tunnel and fit a relocating short shifter. The Nissan CD009 also works with a weld-in tunnel clearance kit, and the later shorter Magnum housing makes shifter placement harder.Medium14

Can an LS-swapped 240SX be smog legal in California?

Yes, through a documented route. The S13 predates 1996, so a GM E-ROD LS3 package with its CARB executive order can be installed in cars up to 4,500 lb test weight. The car then needs a BAR Referee inspection, and the full emissions kit, OEM-style fuel regulation and evaporative system must be in place.Medium1092

Will the stock 240SX differential hold up behind an LS?

Not reliably. Swap guides warn that a high-output V8 pushes the S13 differential and axles beyond their limits, and many US S13s left the factory without a limited-slip differential. Plan for a stronger differential, an LSD and upgraded axles as part of the swap rather than waiting for a failure.Medium45

Does an S13 LS swap kit fit an S14?

Sometimes. The S13 and S14 share the same basic engine bay layout, and some mount designs use an adjustable pedestal to suit both subframes. Other makers sell separate S13 and S14 kits. Check the listing for your exact chassis, and note that S14 SE and LE cars have 5-lug hubs, which changes axle and wheel choices.Medium45

Which LS engine should I use in a 240SX?

The LS1 is the safest starting point because most kits, pans and headers were developed around it. A 5.3 L truck engine is the budget choice but adds iron-block weight. An LS3 crate or E-ROD engine costs more but arrives new, and the E-ROD package is the clearest path to a California-legal car.Medium4110

Related

Sources

13 sources
  1. Nissan 240SX V8 LS3 Engine Swap Guide: Part 1 · Speed Academy · press · retrieved 2026-10-25
  2. Nissan 240SX LS V8 Engine Swap Guide Part 2: Let's Get Started · Speed Academy · press · retrieved 2026-10-25
  3. Nissan 240SX LS V8 Engine Swap Guide Part 3: It's All in the Details · Speed Academy · press · retrieved 2026-10-25
  4. Ultimate 240SX LS Swap Kit Guide · Drifted.com · press · retrieved 2026-10-25
  5. Nissan 240SX · Wikipedia · reference · retrieved 2026-10-25
  6. General Motors LS-based small-block engine · Wikipedia · reference · retrieved 2026-10-25
  7. Dialing In LS Sensors For Various Generations · EngineLabs · press · retrieved 2026-10-25
  8. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  9. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  10. Executive Order D-126-32: GM LS3 E-ROD engine kit · California Air Resources Board · standard · retrieved 2026-10-25
  11. Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-25
  12. StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  13. VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25