Guides

In-depth guides.

The big topics, worked end to end with real numbers, live calculators and sources.

AI tuning explained: how AI-assisted calibration works, and its limitsAI tuning, done safely, is three separate tools: deterministic learners on the ECU that correct fuel from wideband feedback inside fixed limits, validated models whose outputs are clamped, and language models that only translate goals and explain results.Anti-lag guide: how ALS works, throttle kicker vs air bypass, rolling anti-lag, damage and legalityAnti-lag tuning keeps a turbo spinning when the driver lifts off, by retarding ignition heavily, adding fuel and letting extra air past a closed throttle so combustion continues in the exhaust manifold.Boost control and wastegate actuator guide: springs, solenoids and tuning boostA wastegate actuator sets boost: pressure on its diaphragm beats a spring and opens the wastegate, so boost settles near spring pressure.Dyno tuning guide: dyno types, correction factors, dyno sheets and what a session involvesA dyno tune is engine calibration done on a dynamometer, which holds the car at controlled speed and load while the tuner adjusts fuel, spark, boost and limits and measures the result.E85 tuning guide: flex fuel conversion, sensors, sizing and timingE85 tuning means fuelling for a fuel that needs about 1.5 times the mass of gasoline at the same lambda, measuring an ethanol content that varies from 51% to 83% at the pump, and making cold starts work.ECU wiring and installation guide: power, grounds, sensors and first startGood ECU wiring comes down to four things: a fused, switched power feed that holds voltage under cranking; power grounds and sensor grounds kept separate, with sensor ground never joined to chassis; shielded cable for crank, cam and knock signals with the drain wire connected at the ECU end only; and heat-rated wire routed away from coils, injectors and exhaust.ECU tuning explained: engine management basicsECU tuning is the work of adjusting the tables and settings an engine control unit uses to decide how much fuel to inject, when to fire each spark plug and how to drive the throttle, idle, boost and cam actuators.How to datalog an engine and read the logs: channels, rates and math channelsA datalog is a time-stamped record of what the engine did, and a useful one starts with a question.Ignition timing advance and knock: how to tune spark timing safelyIgnition timing advance is how early the spark fires before top dead centre, so peak cylinder pressure lands just after it.Launch control tuning: OEM vs aftermarket, 2-step, 3-step, cut methods and drivetrain stressLaunch control tuning sets how an engine holds a chosen rpm at a standstill and then manages torque as the car pulls away, so starts are quick and repeatable.LS swap guide: engines, mounts, fuel, wiring and ECUAn LS swap fits a GM LS-family V8 (Gen III or Gen IV, 4.8 to 7.0 litres) into a vehicle that never had one.Race car PDM guide: PDM basics and electrical load planningA race car PDM (power distribution module) replaces the fuse and relay box with solid-state switches that measure each channel's current and turn it off on overload, then retry or latch off by rule.Plug and play harness vs wire-in: how to choose an ECU harnessA plug and play harness is an adapter that connects an aftermarket ECU to a car's factory wiring, so nothing is cut.Rev limiter tuning: hard vs soft cut, fuel vs spark cut, setting the limit and diesel governorsRev limiter tuning sets the engine speed the ECU will not exceed and how it enforces it: closing the throttle, cutting fuel, cutting spark or retarding timing, either abruptly (hard cut) or progressively (soft cut).Is ECU tuning safe? Safety, verification and what the AI cannot changeECU tuning is safe when every change is bounded, checked and reversible.Speed density vs MAF: load strategies, VE tables, MAF limits, alpha-N and when to switchSpeed density vs MAF is a choice of how the ECU finds air per cylinder.Standalone ECU guide: standalone vs piggyback vs reflash, I/O planning, costs and legalityStandalone engine management means replacing the factory ECU with a programmable computer that runs the engine on its own calibration.Aftermarket ECU support: what GAINS reads, recommends and never writesOn an aftermarket ECU from another maker, GAINS is an advisor, not a tuner with write access.Turbo sizing: how to read a compressor map and match a turboTurbo sizing matches a compressor and turbine to the airflow and pressure ratio an engine needs across its rpm range.Bosch LSU 4.9 wideband and fuel-system sizing guideThe Bosch LSU 4.9 is the wideband lambda sensor most aftermarket ECUs and gauges use.