LS swap guide: choosing the engine, mounts, fuel, wiring and ECU

An LS swap fits a GM LS-family V8 (Gen III or Gen IV, 4.8 to 7.0 litres) into a vehicle that never had one. Choose the engine first, because its 24x or 58x crank pattern fixes the ECU, harness and throttle parts. Then plan mounts, oil pan, accessory drive, headers, transmission, cooling and a 58 psi EFI fuel system together.46121

Key takeaways

  • Gen III = 24x crank, rear cam sensor; Gen IV = 58x crank, front-cover cam sensor. Engine, sensors, ECU and harness must match.
  • A Gen III PCM can run a 58x engine through a converter box; a Gen IV PCM cannot run a 24x engine.
  • Decode the VIN 8th character and model year before buying. Avoid the front-drive LS4.
  • Fix engine position first: mounts, oil pan, headers and crossmember all follow from it. The truck pan (over 8 in) is too deep for most cars.
  • Accessory drives come in three alignments (Corvette, F-body/GTO, truck). Pulley, water pump and tensioner must share one.
  • Fuel: about 58 psi constant (check your ECU's figure), at least 45 gph for GM's crate LS3, EFI-rated lines and a regulator near the rail.
  • Route the steam ports to a high point, and plan an electric fan.
  • With a factory PCM, VATS must be removed before the engine will start. Most no-starts are grounds, VATS or a trigger mismatch.
Jump to section21

What is an LS swap?

An LS swap means fitting a GM LS-family V8 into a vehicle that never came with one.

First LS engineLS1, 1997 CorvetteC5Sourced34
Generations covered here

Gen III (24x crank, 1997-2007) and Gen IV (58x crank, 2005-2014 era)

Sourced · medium56
Not covered hereGen V LT (direct injection): separate swap and electronicsSourced · medium68

The LS family began with the LS1 in the 1997 Corvette. It covers Gen III (from 1997) and Gen IV (from about 2005) car and truck engines from 4.8 to 7.0 litres.3432

Every LS is a two-valve pushrod V8 with aluminium heads and coil-near-plug ignition. Car blocks are aluminium; truck blocks are aluminium or cast iron. Gen V LT engines (2014 on) look similar but are direct-injected, use different electronics, and are a separate swap.Medium468

A complete swap touches eight systems

Mounts and oil pan, accessory drive, exhaust, transmission, cooling, fuel, wiring and engine control. Most problems come from choosing these one at a time. Engine position, pan, mounts and headers all depend on each other, so plan them together.Medium211

Why the LS became the default V8 swap

Builders pick the LS for four reasons.

It is compact for a V8 because it is a pushrod engine. Truck 4.8 and 5.3 litre engines are cheap and easy to find in junkyards. Swap parts exist for almost every chassis.

And the engines have a reputation for durability.Medium3233

The LS1 was also much lighter than the cast-iron small-block it replaced: Wikipedia puts the saving at almost 100 lb (45 kg). That matters most in light cars, where an iron-block truck 5.3 or 6.0 gives some of it back.Medium4

The supply side is changing. GM's last LS-powered production car was built in 2017, and Chevrolet Performance has started to discontinue some LS crate engines. Junkyard truck engines remain the main entry point.Medium3332

Choosing the engine: Gen III vs Gen IV, truck vs car

Start with the generation, because it fixes the electronics.

Displacement check (GM LS3 crate spec)4.065 in bore × 3.622 in stroke × 8 = 376 cu in6.2 LSourced141

Gen III engines use a 24-tooth crank wheel and a cam sensor at the back of the block. Gen IV engines use a 58-tooth wheel and a cam sensor in the front timing cover. The crank wheel, sensors, ECU and harness must all belong to the same generation.67

Gen III truck (4.8, 5.3, 6.0): the cheap, plentiful choice. Most have iron blocks, cathedral-port heads and a 24x crank. Expect a tall truck intake and a deep truck oil pan, both of which usually need changing in a car.Medium451514

Gen IV truck (2007 on)

58x electronics, and several engines add Active Fuel Management (cylinder deactivation) or variable valve timing. Both need an ECU strategy before you buy; see the AFM and VVT section below.Medium46

Car engines (LS1, LS6, LS2, LS3, L76/L77, LS7): aluminium blocks and lower car intakes. LS1 and LS6 are Gen III cathedral-port engines. The LS3 uses rectangle-port heads, and an intake must match its head's port shape unless you use adapters.Medium4141

Truck intakes are about 3 in (76 mm) taller than car intakes, per Wikipedia. Under a low hood that usually means a car intake or an aftermarket manifold, which then has to match the head's port shape.Medium414

LS engine groups at a glanceMedium546714
GroupCommon RPO codesBlockCrank / camWhat to plan for
Gen III truckLR4 4.8, LM7 5.3, LQ4/LQ9 6.0 (LM4, L33 aluminium 5.3)Mostly iron24x / 1x (rear cam sensor)Tall intake, deep pan, cathedral ports
Gen III carLS1, LS6Aluminium24x / 1xCathedral ports; car pans and accessories vary by car
Gen IV truckLY2 4.8, LY5/LMG/LH6/LC9 5.3, LY6/L96 6.0, L92 6.2Iron or aluminium58x / 4x (front-cover cam sensor), with exceptionsAFM on some, VVT on some; ECU must handle or delete them
Gen IV carLS2, LS3, L76/L77, LS7Aluminium58x / 4x (early LS2 with E40 PCM is 24x)Rectangle ports on LS3; intake must match the head

Buying a junkyard LS: identification and inspection

Identify the engine before you pay.

Gen III truck codes (VIN 8th)
  • V = LR4 4.8
  • T = LM7 5.3
  • U = LQ4 6.0
  • N = LQ9 6.0
  • P = LM4 5.3
  • B = L33 5.3
Sourced · medium5
Gen III car codes (VIN 8th)
  • G = LS1
  • S = LS6
Sourced · medium5
Gen IV truck codes (VIN 8th, examples)
  • C = LY2 4.8
  • J = LY5 5.3
  • K = LY6 6.0
  • 0 = LMG 5.3
  • M = LH6 5.3
  • 8 = L92 6.2
Letters repeat across tables; always decode with the model year.Sourced · medium5

The eighth character of the donor's VIN gives the engine code, which maps to an RPO such as LM7 or LY5. A 4.8 and a 5.3 look nearly identical from outside, so the VIN or the build sheet is the reliable check.531

Decode the VIN letter together with the model year and vehicle type. The same letter means different engines in different tables: in PSI's decoder, U is an LQ4 in a Gen III truck but an LS2 in a Gen IV car.Medium5

Avoid the LS4 unless you want its problems. It is a 5.3 built for transverse front-drive cars, with a shortened crankshaft, a different bellhousing pattern and a remote water pump. It does not drop into a rear-drive swap like a truck 5.3.4531

Take the electronics with the engine when you can: harness, PCM, pedal, throttle body and sensors. They are a matched set for that generation, and the right pieces cost more to find later. Ask about a warranty; one LSX Magazine writer's yard offered 90 days.Medium8631

Junkyard LS inspection checklistMedium3154
CheckHowWalk away or budget for a rebuild if
☐ Engine codeVIN 8th character or RPO sticker; match to model yearIt is an LS4, or the code does not match what you were sold
☐ Turns over24 mm socket and breaker bar on the crank boltIt will not rotate a full turn
☐ OilDrain it and look in the panWater, sludge, metal, or suspiciously fresh oil on a dead engine
☐ Valve coversPull one and look at pushrods and rockersRusty pushrods (water or outdoor storage)
☐ Intake portsLook in the manifold runnersHeavy oily buildup (blow-by, high mileage)
☐ Spark plugsPull all eight and compareOil-soaked plugs, or one cylinder unlike the rest
☐ CompressionTest on the stand, turning the crank by handOne cylinder far below the others
☐ Exhaust boltsCheck every manifold boltSnapped bolts in the head (costly to extract)
☐ Donor historyMileage, why it was scrapped, how long it satFront-end crash, flood, or a seller who will not answer

24x vs 58x, 1x vs 4x cam, and cable vs drive-by-wire

The crank reluctor wheel tells the ECU where the crankshaft is.

Gen III 24x crank sensor12 V, usually black connectorSourced7
Gen IV 58x crank sensor5 V, usually grey connectorSourced7
Cam sensorGen III: rear of block (1x). Gen IV: front timing cover (4x)Sourced67
Knock sensors

Gen III: under the intake in the valley. Gen IV: sides of the block

Sourced7

Gen III uses 24 teeth (a two-piece wheel) and Gen IV uses 58 (one piece). Gen III cam sensors sit at the rear of the block; Gen IV sensors sit in the front timing cover. Neither pattern makes more power.67

The sensors differ electrically too. Gen III 24x crank sensors are 12-volt and usually black; Gen IV 58x sensors are 5-volt and usually grey. Do not trust colour alone: GM has made some 58x sensors black, and aftermarket sensors may not follow the code.76

Mixing generations only works one way. A Gen III PCM can run a 58x engine through a 58x-to-24x converter box. Michigan Motorsports told EngineLabs there is no way to make a Gen IV PCM run a 24x engine.

Changing the reluctor wheel itself means timing-cover and cam-gear work.76

Gen III engines ran either a throttle cable or drive-by-wire from the factory, while 58x engines with GM controls use drive-by-wire only. With drive-by-wire, the pedal, throttle body and ECU must come from the same generation. A cable harness will not run a drive-by-wire engine.6811

Exceptions exist

EngineLabs lists early LS2 engines with the E40 PCM, some LH6 SUVs and early LS2 CTS-V and TrailBlazer SS engines as 24x with the cam sensor in the timing cover. Check the parts on your engine, not the generation label.Medium7

Will this engine run on that controller?Medium6728
Engine triggerControllerResult
24x crank / 1x cam (Gen III)Gen III GM PCM (P01, P59)Native match
58x crank / 4x cam (Gen IV)Gen IV GM ECM (E38, E67)Native match; transmission usually needs a separate TCM
58x crank (Gen IV)Gen III GM PCMWorks only with a 58x-to-24x converter box
24x crank (Gen III)Gen IV GM ECMNot possible, per Michigan Motorsports
24x or 58xAftermarket standalone ECUWorks when the ECU and harness are set up for that pattern; buy the matching kit
24x/1x or 58x/4x, carburettorMSD 6014 / 60143 ignition controllerController detects the pattern automatically

AFM/DOD and VVT on later trucks: what to do about them

AFM engines (per Wikipedia)LH6, LY5, LMG, LC9, LS4, L76, LZ1Sourced · medium4
VVT engines (per Wikipedia)
  • LY6, L96, L20, LZ1, L76
  • LC9 from 2010
Sourced · medium4
Gen IV truck with neitherLY2 4.8Sourced · medium4

Active Fuel Management (first called Displacement on Demand) shuts off four cylinders at light load using special lifters and an oil-control valve. Wikipedia lists it on the LH6, LY5, LMG, LC9, LS4, L76 and LZ1. Variable valve timing (a cam phaser) appears on the LY6, L96, L20, LZ1, L76, and on the LC9 from 2010.Medium4

You have three choices. Keep AFM and VVT working, which needs an ECU and calibration that support them. Disable AFM in the calibration and leave the hardware in place.

Or remove the AFM hardware, which also needs the feature turned off in the ECU.Medium304

A full AFM delete typically replaces the 16 lifters, the valley cover and the camshaft with non-AFM parts; Michigan Motorsports also lists lifter guide trays, head gaskets and head bolts in some kits. Whatever parts you use, the AFM function must be disabled in the engine computer.Medium30

Check the ECU before buying a VVT or AFM engine. One retailer listing for a 58x drive-by-cable standalone kit states that it does not operate VVT or DOD. If your ECU cannot drive the cam phaser, plan the cam hardware with your cam supplier first.Low274

LS swap engine mounts and oil pans

LS engine mounts bolt to the block differently from earlier small-block Chevys, so an older chassis needs either LS-specific mounts or adapter plates that take small-block mounts. Pick the engine position first; the mounts, oil pan, headers and crossmember all follow from it.Medium1821

Adapter plates usually offer several positions. Speedway's ICT Billet install suggests starting in the rearmost position and moving forward if the firewall or headers are tight. Those plates also raise the crank centreline slightly, by 0.177 in in that case.Medium18

Ground clearance is the oil pan's job. Speedway measured the GM truck pan at over 8 in tall, which is too low for most cars. The F-body pan is about 5 5/8 in at the sump and sits behind many crossmembers, which is why it is a common swap choice.Medium15

A swap pan only works with its matching pickup tube, and windage tray and stroke limits matter. GM's 19212593 pan lists a 3.620 in maximum stroke with its windage tray. Holley says its 302-2 pan is not for LS7 engines or strokers over 3.62 in.Medium192015

Measure before you buy. Check the pan against the crossmember, steering linkage and ground with the engine at its final height and the car at ride height. A pan that fits on the bench can hit once the suspension is loaded.Medium2115

Common LS swap oil pans (depths as published by the source)Medium15192016
PanPublished depthWhere it is usedWatch for
GM truck panOver 8 in tallTrucks and SUVsUsually too low for a car
F-body (Camaro / Firebird) panAbout 5 5/8 in at the sump, about 5 qtThe common car-swap panRear sump; check crossmember and steering
Chevrolet Performance 19212593About 7.75 in at the sump1955-1995 rear-sump RWD GM cars and trucks3.620 in max stroke with windage tray
Holley 302-2Not stated; more front clearance than 302-1F-, A-, G-body, Nova and similarNot for LS7 or strokers over 3.62 in
Speedway fabricated steel panAlmost 6 in sump, 7 qtUniversal swap panNeeds its own pickup
Hummer H3 (LH8) panNot statedSpeedway's pick for 1973-87 C10 trucksCheck against your crossmember

Accessory drive spacing: truck vs car vs F-body vs Corvette

LS front drives come in three belt alignments, set by the crank pulley.

Mixing groupsWater pump, tensioner and crank pulley must share one alignmentSourced1213
Supercharged Corvette noteHolley's Corvette references are for non-supercharged LS enginesSourced12

Holley calls them Standard (Corvette, CTS-V, G8), Middle (F-body Camaro/Firebird and GTO) and Long (all trucks and the 2010-on Camaro). ICT Billet calls the same groups -1, -2 and -3.1213

The water pump and tensioner are alignment-specific, so parts must come from one group. A truck balancer with a Corvette water pump will not line up. If you keep the existing crank pulley and pump, Holley says it is cheapest to space the other accessories to match.1213

Shorter is not automatically better. The Corvette-style Standard alignment puts the belt closest to the block, which helps radiator clearance; Holley notes it may be preferred when the radiator is tight. The truck drive is the longest and easiest to find in a junkyard.Medium1213

LS belt alignment groups1213
AlignmentApplicationsHolley crank-pulley referenceICT offset vs Corvette
Standard (-1)Corvette, CTS-V, G81.5 in (37 mm)Baseline
Middle (-2)1998-2002 F-body, 2004-06 GTO2.25 in (55 mm)About 0.86 in further outboard
Long (-3)Trucks, 2010-15 Camaro3 in (75 mm)About 1.57 in further outboard

LS swap headers and exhaust

Headers are chassis-specific; there is no universal LS swap header.

Holley points out that compact exhaust manifolds avoid the bend-radius limits headers face, so they fit where a header cannot, especially in bays never designed for an LS.Medium2221

Swap headers commonly need related changes: relocating power-steering or A/C brackets, modifying the dipstick tube, clearancing the steering shaft or clutch linkage, and moving oxygen sensor bungs. JEGS advises test-fitting headers before painting or coating them.Medium23

Plan oxygen sensor bungs with the exhaust, not afterwards. JEGS notes sensors may need relocating on some applications, and some swap headers come with bungs already welded in. Our wideband guide covers where a wideband should sit.Medium23

Exhaust choices affect emissions legality. GM's crate engine instructions note that federal law restricts removing required emission controls on road vehicles, and that many states prohibit tampering. Check your state's rules before you cut anything.137

Transmission choices: T56, 4L60E, 4L80E and adapters

The LS keeps the GM V8 bellhousing pattern, so GM rear-drive transmissions bolt up.

TCI told Chevy Hardcore that the TH350, TH400 and Powerglide dowels line up and five of six bellhousing bolts align. The torque converter and flexplate still need the right pilot and bolt pattern.Medium24

Electronic automatics (4L60E, 4L65E, 4L80E, 6L80E) need a controller. A Gen III PCM can run both engine and transmission; 58x engines usually use a separate TCM, except the 6L80 and 6L90, which pair with 58x controllers. Standalone ECUs and dedicated transmission controllers can also do it.Medium62426

Older non-electronic automatics need their mechanical controls back: a kickdown cable (TH350), a correctly adjusted TV cable (700R4) or a vacuum source (TH400). Factory EFI throttle bodies have no provision for those cables, so expect fabrication.Medium24

Manual swaps need the right pilot bearing. GM lists two for the LS3: one for long input shafts and one for short. A worn or wrong one causes shifting problems and rapid clutch wear.

Verify the fit before the transmission goes in.1

LS swap transmission optionsMedium25246
TransmissionTypeController neededNotes from the sources
T56 / T56 Magnum6-speed manualNo (speed signal only)Transmission Digest: Magnum rated 700 lb-ft vs about 450 for the original T56
4L60E / 4L65E4-speed automaticYes (PCM, TCM or standalone)Common and compact; TCI rates a stock unit at about 450 hp
4L80E4-speed automaticYesStronger and larger; may need floor or crossmember work
6L80E6-speed automaticYes (OE-style control)Larger; Chevy Hardcore advises it only in specific cases
TH350 / TH400 / PowerglideNon-electronic automaticNoBolts up; needs converter/flexplate match and kickdown, TV or vacuum provision

LS swap radiator, fans and steam ports

The LS thermostat sits low, in the water pump housing, so air collects in the heads.

Steam portsFour on early engines, two on later enginesSourced · medium3534
Where steam lines goA high-point fitting on the radiator or a tapped water-pump portSourced · medium35
Warm-up before hard use (GM crate LS3)Oil and coolant at 180 °F before towing or full-throttle runsSourced1

GM added steam ports to vent it. Holley's Jeremy Stoermer told LSX Magazine that trapped air causes hot spots and can lead to overheating, detonation and pre-ignition.3534

Early LS engines have four steam ports (two front, two rear); later ones have two at the front. Route the steam line to a fitting at a high point: the radiator or a tapped port on the water pump. Earl's recommends the four-port kit when the engine sits level or nearly level.Medium3534

Radiator inlet and outlet position is the usual fitment problem. LS swaps often need both ports on the passenger side, which is why swap radiators are offered as dual-pass units. Check your water pump's outlet direction before buying.Medium36

Most swaps lose the truck's belt-driven fan, so plan an electric fan and its control. Chevrolet Performance's controller kit lists an electric cooling fan among the few parts the installer must add.Medium21

LS swap fuel system: 58 psi, pump sizing and regulator choice

An LS needs much higher fuel pressure than a carburettor.

Base pressure (GM crate LS3)
  • 58 psi constant
  • GM documents also quote 60 psi400 kPa
Sourced12
Minimum pump flow (GM crate LS3)45 gph at the recommended pressureSourced1
Controller-kit flow requirement
  • 40 gphLS2, LS3, LS376
  • 50 gphLSX454, LS7
Sourced · medium2
Lines (PSI)AN-6 feed and returnSourced · medium916
Pump (PSI)A 255 L/h in-tank pump covers most buildsSourced · medium9

GM's LS3 crate instructions give 58 psi constant pressure and a pump that flows at least 45 gph at that pressure. The same document also quotes 60 psi, and GM's controller kit specifies 60 psi, so follow your ECU's stated figure.129

Return style is the safer default for most swaps. The pump flows more than the engine uses and a regulator near the rail returns the rest, which keeps pressure steady and the pump cool. PSI recommends mounting the regulator as close to the rail as possible to reduce vapour-lock risk.Medium9

Returnless works when the regulator sits in the tank or pump module and the module is designed for it. Chevrolet Performance sells a filter-regulator (19239926) that holds the correct pressure for its crate engines, and PSI notes some factory trucks used returnless systems.Medium91

Use EFI-rated parts throughout

An in-tank pump in a baffled tank, AN-6 or equivalent feed and return lines, and hose rated for the pressure, not parts-store rubber hose and clamps. Gen III and IV blocks have no mechanical fuel pump boss, so even a carburetted LS needs an electric pump.Medium91628

Size the pump and injectors for your target
hp
:1

Typical: gasoline NA 0.45-0.50, gasoline boosted 0.55-0.65, E85 NA 0.65-0.75, E85 boosted 0.80-0.90 lb/hp-hr.

g/cc
%
psi
psi

Result

Pump flow required171 L/h
At pump outlet pressure58.0 psi
Engine consumption (no margin)137 L/h

Planning estimate from the formula below, not a measurement.

Open the fuel pump size calculator →
hp
:1

Typical: gasoline NA 0.45-0.50, gasoline boosted 0.55-0.65, E85 NA 0.65-0.75, E85 boosted 0.80-0.90 lb/hp-hr.

%

Size for 80-85% so the injector still has control margin at peak power.

Result

Flow per injector35.2 lb/hr
Total fuel flow225 lb/hr

Planning estimate from the formula below, not a measurement.

Open the fuel injector size calculator →

LS swap wiring harness: standalone vs modified factory

There are three harness routes.

Rework the donor's factory harness yourself. Buy a factory-style standalone harness built for a GM PCM. Or use the harness that comes with an aftermarket ECU kit.

All three must match the engine's generation, throttle type and transmission.Medium1782

With a factory PCM, the anti-theft system (VATS) must be removed in the calibration or the engine will not start. A tuner also programs out missing emissions hardware and sets the transmission type. Speedway notes some harness makers offer this as a mail-in service.171116

A standalone LS harness is mostly plug-in, but you still terminate a handful of vehicle wires: battery, ignition, starter, alternator, cooling fan, A/C and fuel pump, per Speedway's squarebody guide. Plan relays and fuses for the pump and fan.Medium162

Plug-and-play means the ECU plugs into a harness made for that engine. Wire-in means you terminate a universal loom. For a swap, the engine harness is new either way; the question is how much of it arrives already terminated.

Our harness guide compares the options.Medium843

Grounds cause more odd faults than anything else in a swap. PSI lists five paths: battery to block, head to firewall, block to frame, frame to cab on trucks, and a fuel pump ground. Use bare metal, star washers, 4 AWG or larger battery-to-block, and no smaller than 10 AWG elsewhere.Medium1011

Test grounds under load. Measure volts between battery negative and the block while cranking; PSI treats more than 0.1 V as resistance in the ground path. Bad grounds mimic failed sensors, misfires and stalling, so check them before replacing parts.Medium1110

Drive-by-wire pairing: what must matchMedium8116
PartMust matchIf it does not
Accelerator pedalECU generation and part familyPedal codes or limp mode
Electronic throttle bodyECU generation (Gen III, Gen IV and Gen V are not interchangeable)Throttle mismatch codes, no throttle
HarnessEngine generation and throttle type (cable or wire)No communication; a cable harness cannot run a DBW engine
CalibrationThe throttle hardware actually fittedErratic throttle or idle; relearn after install
Wire size for the fuel pump feed
A
V
%
°F

Hot engine bays raise copper resistance about 0.4% per °C.

Result

Smallest AWG: 10 AWG2.11 %voltage drop
Smallest metric: 4 mm²2.77 %voltage drop

Voltage drop is one check. The wire must also be rated for the current at its temperature and bundling, and the fuse must protect the wire.

Planning estimate from the formula below, not a measurement.

Open the automotive wire gauge calculator →

LS swap ECU options: factory reflash vs standalone

There are four common ways to run an LS.

Reprogram the factory GM PCM. Use a Chevrolet Performance controller kit. Fit an aftermarket standalone ECU.

Or fit a carburettor with a separate ignition controller. Each has a different cost, wiring job and tuning path.Medium1722628

Factory PCM reflash

The donor PCM is reprogrammed with commercial GM tuning software (HP Tuners is one maker). HP Tuners warns that a vehicle with a different controller than it came with may not be supported, so confirm support for your PCM before buying.Medium2917

Chevrolet Performance controller kit

A standalone GM system for crate engines with 58x crank, 4x cam and electronic throttle. The kit includes the ECM with a calibration, harness, pedal, MAF sensor and two oxygen sensors. You add power, ground, a fuel pump and an electric fan.Medium2

Aftermarket standalone

Kits are sold by crank pattern, and features vary by part number. On Holley's pages, the base Terminator X has no drive-by-wire, while Terminator X Max versions add drive-by-wire, 4L60E/4L80E control, or both.Medium26

Carburettor

An LS has coil-near-plug ignition and no distributor, so a carb swap still needs an ignition controller. MSD's 6014 detects 24x/1x or 58x/4x patterns and has a built-in MAP sensor for timing. An electric fuel pump is still required.Medium284

LS swap engine control optionsMedium172262829
OptionBest whenWatch for
Factory PCM, reflashedComplete donor package; you want factory drivability and transmission controlVATS and emissions removal, a tuner for your PCM, generation-matched pedal and throttle
Chevrolet Performance controller kit58x / 4x / electronic-throttle crate engineKit is per engine; you supply fan, pump, power and ground
Aftermarket standalone ECUMixed or modified parts, boost, data logging, no donor PCMPick the right crank-pattern kit; check DBW, transmission, VVT and AFM support by part number
Carburettor + ignition controllerSimplest fuel side, older vehiclesStill needs electric pump, ignition controller and an electronic-trans controller if fitted

First start and break-in checklist

Most no-starts after a swap are electrical, not mechanical.

Oil pressure minimum, hot (GM LS3 crate)
  • 6 psi at 1,000 rpm
  • 18 psi at 2,000
  • 24 psi at 4,000
Sourced1

Work through PSI's checks in order: VATS removed, crank signal seen as rpm on a scan tool while cranking, injector pulse on a noid light, spark, then fuel pressure at 58 psi with the pump priming at key-on.11

GM's crate engine instructions require priming the oil system before the first start, using a pre-luber through the left front oil gallery until the oil pressure gauge moves. Fill and check every other fluid too: coolant, power steering and transmission.1

GM's break-in for its new crate LS3 then calls for varied driving with no wide-open throttle for the first 30 miles or one hour, a set of 50% and 100% throttle pulls to about 4,000 rpm, an oil and filter change, 500 gentle miles, and a second oil change.1

Key-on to first drive1111035
StepWhat to confirmWhy
☐ 1. FluidsEngine oil to GM spec, coolant, transmission and steering fluidsGM ships crate engines dry
☐ 2. Oil primePre-lube until oil pressure showsRequired by GM before first start
☐ 3. GroundsUnder 0.1 V battery-negative to block while crankingBad grounds mimic sensor faults
☐ 4. Key-onPump primes; 58 psi (or your ECU's figure); no leaksPressure and leaks before spark
☐ 5. Crank signalScan tool or laptop shows rpm while crankingNo rpm = trigger, harness or ECU mismatch
☐ 6. First startListen; hold about 1,000 rpm to operating temperatureGM crate procedure
☐ 7. CoolingBleed air through the steam ports; watch for hot spotsLow thermostat traps air
☐ 8. DataLog lambda, fuel trims, oil pressure and coolant temperatureFind faults before load
☐ 9. Break-in30 miles varied load, no WOT; pulls to 4,000 rpm; oil changeGM crate break-in

Common LS swap mistakes and failure modes

Most expensive mistakes come from buying parts before the plan is fixed.

The table lists the failure modes the sources report most often, what they cause and how to avoid them. Read it before you order anything.Medium112131

Diagnose before you buy parts. PSI warns against replacing whatever part a trouble code names: an oxygen sensor code can come from a ground fault or an exhaust leak, and heat-related stalls often trace to relays, crank sensors or grounds.Medium11

LS swap failure modesMedium11610811512359430
MistakeWhat happensPrevention
24x engine with 58x electronics, or the reverseCranks, never firesMatch crank wheel, sensors, ECU and harness
VATS left in a factory PCMNo start, or starts and diesHave the PCM programmed before first start
Missing or painted-over groundsOdd sensor codes, misfires, stallingFive ground paths on bare metal; voltage-drop test
Pedal, throttle body and ECU from different generationsNo throttle or limp modeBuy them as a matched set
Wrong pilot bearingShifting problems, clutch wear, damageMatch long or short input shaft
Truck pan or wrong pan for the crossmemberEngine sits too high or pan hangs lowChoose engine position, mounts and pan together
Mixed accessory alignment partsBelt misalignmentOne alignment group for pulley, pump and tensioner
Steam ports capped or ignoredAir pockets and hot spotsRoute steam lines to a high point
Carburettor-era fuel partsLow pressure, hose failuresEFI pump, regulator, AN or rated hose
Regulator far from the railVapour-lock riskMount the regulator close to the rail
AFM or VVT engine on an ECU that cannot run itFaults or forced deleteCheck ECU support before buying the engine
LS4 bought as a 5.3Short crank, wrong bellhousingDecode the VIN and RPO

LS swap budget: what you will pay for

An LS swap costs far more than the engine.

GM's own crate engine instructions list what does not come in the box: the engine control system and harness, flexplate or flywheel, starter, fuel pump, accessory drive and exhaust manifolds. A junkyard engine adds inspection and refresh parts on top.131

Swap kits are sold in levels, from mounts alone up to pan, headers, exhaust and a full accessory drive. Compare what each level includes before comparing prices, and price every category below for your own car before you buy the engine.Medium21

LS swap budget categories (no prices: they vary by chassis and change often)Medium12131
CategoryWhat it coversWhat drives the cost
☐ EngineJunkyard, used or crate engine; gaskets, seals, refresh partsGeneration, condition, AFM/VVT delete
☐ Mounts and crossmemberEngine mounts or adapters, transmission crossmemberChassis kit availability
☐ Oil pan systemPan, pickup, windage tray, dipstickGround and crossmember clearance
☐ Accessory driveAlternator, power steering, A/C, brackets, beltKeeping the donor drive vs a new kit
☐ ExhaustHeaders or manifolds, pipes, O2 bungsChassis-specific headers
☐ TransmissionGearbox, bellhousing, clutch or converter, flexplate, pilot bearing, driveshaftManual vs electronic auto
☐ CoolingRadiator, electric fans, steam lines, hosesPort positions and fan control
☐ Fuel systemPump, tank or module, regulator, filter, linesReturn vs returnless; tank baffling
☐ Wiring and ECUHarness, ECU or PCM programming, pedal, sensors, relaysFactory reflash vs standalone
☐ Tuning and inspectionCalibration, dyno or road time, emissions or safety inspectionLocal rules and who tunes it

LS swap guides by car

This guide covers what every LS swap shares.

Each car then has its own problems: subframes, steering shafts, differentials, gauges and the local rules for registering the result. Our chassis guides cover those car by car, with mount, transmission and wiring notes for each.Medium21

If your car is not listed yet, the sections above still apply. For a donor engine, the GM car and truck pages below show which LS each model used; confirm yours by decoding the VIN.Medium5

Do it with GAINS (pre-release, roadmap)

GAINS: the ECU2 is our pre-release V8 controller, designed to the published Nexus S3 harness pinout.

Its concept covers GM LS Gen III and IV engines with sequential injection, eight coils, two drive-by-wire channels, two knock inputs and an onboard wideband controller. It is not on sale and has not run an engine.4243

For harnesses, the planner will offer paths in this order: an existing plug-in harness for that pinout, then a third-party factory-to-S3 harness, then wire-in. Every path is labelled pin-compatible per the published pinout, not yet fit-tested, until real harness fit logs exist.43

GAINS does not reflash factory or third-party ECUs. On a GAINS ECU, first-start commissioning and on-ECU learning are designed to run inside a signed safety envelope, with nothing in the real-time path depending on a phone or the cloud. These features are roadmap and unvalidated on a running engine.4445

Frequently asked

What is an LS swap?

An LS swap is fitting a GM LS-family V8, such as a truck 5.3 or an LS3, into a vehicle that did not come with one. The LS family started with the LS1 in the 1997 Corvette and covers Gen III and Gen IV engines. The swap includes mounts, oil pan, exhaust, transmission, cooling, fuel, wiring and engine control.3421

What does an LS swap kit include?

It depends on the maker and level. Holley's Swap Essentials kits step up from mounts to a chassis-matched oil pan, then headers or manifolds, exhaust, and a complete accessory drive. Few kits include the fuel system, harness or ECU, so budget those separately.Medium21

What fuel pump do I need for an LS swap?

One that holds the ECU's specified pressure, typically 58 psi, with flow to spare. GM asks for at least 45 gph at that pressure for its crate LS3, and PSI says a 255 L/h in-tank pump covers most builds. Size it for your target with the fuel pump calculator.1939

What oil pan should I use for an LS swap?

One that clears your crossmember and the ground with the engine at its final height. The truck pan is over 8 in tall and too low for most cars. The F-body pan, about 5 5/8 in at the sump, is the common choice, with swap pans from GM and Holley for older GM chassis.Medium151920

Do I need a special radiator for an LS swap?

Often. LS water pumps tend to need both radiator ports on the passenger side, so swap radiators are often dual-pass, and you need a fitting for the steam line. Plan an electric fan too, because most swaps lose the belt-driven fan.Medium36352

What ECU do I need for an LS swap?

One that matches the engine's crank pattern (24x or 58x), throttle type and transmission. The options are a reprogrammed factory PCM, a Chevrolet Performance controller kit, an aftermarket standalone ECU, or a carburettor with an ignition controller such as the MSD 6014.Medium622628

Can I use a 58x engine with a 24x harness and PCM?

Only with a 58x-to-24x converter box, according to the sources. Michigan Motorsports told EngineLabs there is currently no way to run a Gen IV PCM on a 24x engine. A standalone ECU can be set up for either pattern.76

Can you put a carburettor on an LS?

Yes, with a carburettor intake, an electric fuel pump and an ignition controller, because the LS has no distributor. MSD's 6014 controller reads both 24x/1x and 58x/4x patterns. An electronic automatic still needs its own controller and a throttle position signal.Medium2824

What fuel line size for an LS swap?

PSI and Speedway both use AN-6 for feed and return on typical swaps. Whatever size you choose, it must be rated for EFI pressure: push-lock or AN hose, not parts-store rubber hose with clamps.Medium916

Related

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

45 sources
  1. LS3 EFI crate engine installation instructions and specifications, part no. 19419889, REV 15AP20 (parts not included, fuel pump, pilot bearing, start-up and break-in) · Chevrolet Performance (General Motors); retailer-hosted copy · oem · retrieved 2026-10-27
  2. LS2/LS3 Engine Controller Kit 19540147: 58x/4x/electronic-throttle standalone kit, contents and what the installer supplies; controller-kit fuel requirement (400 kPa / 60 psi, 40-50 gph) · Chevrolet Performance (General Motors), via JEGS listing · oem · retrieved 2026-10-27
  3. SAE Technical Paper 970915: 1997 GM 5.7 Liter LS1 V8 Engine (Amann et al., General Motors Powertrain) · SAE International · sae-paper · retrieved 2026-10-27
  4. GM LS engine (generations, block materials, truck intake height, AFM and VVT applications, LS4) · Wikipedia · reference · retrieved 2026-10-27
  5. LS & LSX engine guide and VIN decoder (8th-digit engine codes by RPO, Gen III 24X / Gen IV 58X tables) · PSI Conversion · reference · retrieved 2026-10-27
  6. 24x vs 58x Reluctor Differences for LS and LT (Chris T., 2026-05-15) · PSI Conversion · press · retrieved 2026-10-27
  7. Dialing In LS Sensors For Various Generations With Michigan Motorsports (G. Acosta, 2025-11-11) · EngineLabs · press · retrieved 2026-10-27
  8. Drive-by-Wire vs. Drive-by-Cable LS Harness: Which Should You Use? (Chris T., 2026-01-22) · PSI Conversion · press · retrieved 2026-10-27
  9. LS and LT Swap Fuel System Guide (Chris T., 2026-05-15) · PSI Conversion · press · retrieved 2026-10-27
  10. LS and LT Swap Grounds and Why They Matter (Chris T., 2026-04-30) · PSI Conversion · press · retrieved 2026-10-27
  11. How to Troubleshoot LS Swap Electrical Issues (2026-03-17) · PSI Conversion · press · retrieved 2026-10-27
  12. Accessory Drive Kit 20-159 / 20-160 / 20-162 fitment and required components guide (crank pulley belt alignment table) · Holley Performance Products; copy hosted by Vivid Racing · vendor-doc · retrieved 2026-10-27
  13. LS crank pulley and harmonic balancer swap guide (-1 / -2 / -3 belt spacing and offsets) · ICT Billet · vendor-doc · retrieved 2026-10-27
  14. LS intake ports swap guide (cathedral vs rectangle port; intake must match head) · ICT Billet · vendor-doc · retrieved 2026-10-27
  15. Speedway Tech Talk: LS Oil Pans (truck, F-body and fabricated pan depths) · Speedway Motors, The Toolbox · press · retrieved 2026-10-27
  16. Squarebody LS Swap Guide (1973-87 C10 parts list: LH8 pan, AN-6 fuel line, wires the installer terminates) · Speedway Motors, The Toolbox · press · retrieved 2026-10-27
  17. Speedway Tech Talk: LS Wired! (factory PCM reprogramming, VATS, transmission notes) · Speedway Motors, The Toolbox · press · retrieved 2026-10-27
  18. Installing ICT Billet LS Motor Mount Adapters (positions, crank centreline rise) · Speedway Motors, The Toolbox · press · retrieved 2026-10-27
  19. Muscle Car Oil Pan Kit 19212593 for Gen III/IV LS engine swaps (listing: sump depth, applications, stroke limit with windage tray) · Chevrolet Performance (General Motors), via JEGS listing · vendor-doc · retrieved 2026-10-27
  20. LS swap oil pan 302-2 product page (front clearance, applications, stroke and LS7 limits) · Holley · vendor-doc · retrieved 2026-10-27
  21. How Holley's Swap Essentials kits simplify the LS/LT swap process (kit levels; engine position, pan, mounts and headers are linked) · Holley (blog) · press · retrieved 2026-10-27
  22. Headers vs Exhaust Manifolds: Which is Best for Your LS Swap? · Holley (blog) · press · retrieved 2026-10-27
  23. GM LS engine swap headers for 1967-1999 GM trucks (fitment notes: bracket, dipstick, steering shaft, O2 relocation, test-fit) · JEGS · vendor-doc · retrieved 2026-10-27
  24. LS Swap Automatic Transmission Guide (P. Huizenga, 2016-02-24) · Chevy Hardcore · press · retrieved 2026-10-27
  25. Tremec T56 Magnum (torque capacity versus the original T56) · Transmission Digest · press · retrieved 2026-10-27
  26. Terminator X and Terminator X Max LS kit product pages (550-903, 550-926, 550-929: drive-by-wire and 4L60E/4L80E control by part number) · Holley · vendor-doc · retrieved 2026-10-27
  27. Terminator X MPFI controller kit, 58x crank / 4x cam, drive-by-cable, EV6 (retailer listing stating VVT and DOD are not operated) · Retailer listing (webshopmanager storefront) · vendor-doc · retrieved 2026-10-27
  28. MSD's LS Series Ignition Controller Means LS Swaps and a Carburetor Too (6014 / 60143) · MSD Ignition (Holley) · vendor-doc · retrieved 2026-10-27
  29. Tuning and Diagnostic Support for GM Vehicles (supported GM controllers; swapped controllers may not be supported) · HP Tuners · vendor-doc · retrieved 2026-10-27
  30. Gen IV 5.3 AFM/DOD delete kit for LMG, LY5, LH6, LC9 (contents; AFM must be disabled in the PCM) · Michigan Motorsports · vendor-doc · retrieved 2026-10-27
  31. The Do's And Don'ts Of Buying A Used LS Engine For A Project (B. Havins, 2019-06-14) · LSX Magazine · press · retrieved 2026-10-27
  32. LS Engine Swaps Explained (And Why They're So Popular) (M. Cowley, 2024-03-07) · SlashGear · press · retrieved 2026-10-27
  33. Why The LS-Series Is Still Such A Popular Choice For An Engine Swap (C. Clougher, 2026-05-26) · Jalopnik · press · retrieved 2026-10-27
  34. Why Do LS Engines Have Steam Tubes? (C. Krome, 2025-10-26) · Jalopnik · press · retrieved 2026-10-27
  35. Do LS Engines Really Need Steam Tubes? Earl's Performance Plumbing interview (J. Sicht, 2019-09-06) · LSX Magazine · press · retrieved 2026-10-27
  36. Radiators for Engine Swaps (2013-11-12) · Street Muscle · press · retrieved 2026-10-27
  37. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (2020) · U.S. Environmental Protection Agency · standard · retrieved 2026-10-27
  38. internal GAINS internal: Fuel injector size calculator (@aitune/calc injector-size); example computed 2026-10-27
  39. internal GAINS internal: Fuel pump size calculator (@aitune/calc fuel-pump-flow); example computed 2026-10-27
  40. internal GAINS internal: Automotive wire gauge calculator (@aitune/calc wire-gauge); example computed 2026-10-27
  41. internal GAINS internal: Engine displacement calculator (@aitune/calc displacement)
  42. internal GAINS internal: ECU2 v0 concept (hardware/mini-duo/CONCEPT.md): S3 pinout, 8 injector / 8 ignition, 2 DBW half-bridges, 2 knock, onboard LSU 4.9; GM LS Gen III/IV in coverage
  43. internal GAINS internal: Plug-and-play harness strategy (owner decision 2026-10-25): S3 plug-in SKU, else third-party factory-to-S3, else wire-in
  44. internal GAINS architecture decision record: ADR-0009: First-start self-commissioning
  45. internal GAINS architecture decision record: ADR-0004: Layered real-time adaptation under a signed authority envelope