Automotive wire gauge

AWGwire sizecable cross-sectionmm² wire sizeampacity

Automotive wire gauge is the conductor size of a vehicle cable, given in American Wire Gauge (AWG) or square millimeters. Choosing it means meeting two limits: the current the wire can carry without overheating its insulation, and the voltage it loses over the circuit's length. Smaller AWG numbers mean thicker wire.123

How it works

In AWG, every three gauge steps roughly halves or doubles the copper area, and every six steps halves or doubles the diameter.

Typical values: 18 AWG is about 0.82 mm² with roughly 21 mΩ per meter, 14 AWG about 2.08 mm² and 8.3 mΩ/m, and 10 AWG about 5.26 mm² and 3.3 mΩ/m.1

Ampacity is the continuous current a cable can carry without exceeding its insulation temperature rating. It is not a single number per gauge: it falls with higher ambient temperature, bundling with other wires and enclosure, and rises with higher-temperature insulation.Medium24

SAE J1128 covers low-voltage primary cable for road vehicles, including common types such as GPT, TXL and GXL, which differ in insulation material and wall thickness. Cross-linked thin-wall types like TXL save space and weight and tolerate engine-bay temperatures better than general-purpose PVC wire.Medium34

Voltage drop often sets the gauge before heating does. Resistance scales with length, so a long run to a rear-mounted fuel pump may need a much larger wire than its current alone suggests. Remember that current travels out and back, so the circuit length includes the ground return.51

In tuning

High-current loads added during a build, such as fuel pumps, fans and water pumps, need wiring sized for their current and run length. Low supply voltage at a pump reduces its flow, which can show up as falling fuel pressure at high load.Medium56

Safety note

The fuse protects the wire, not the load. Size each fuse at or below the rated current of the smallest wire it feeds and place it as close as practical to the power source. An undersized wire behind an oversized fuse can overheat and start a fire without blowing the fuse.Medium72

Formula and worked example

V_drop = I × (R_per_m × L_total)
V_drop
voltage lost in the wireV
I
load currentA
R_per_m
conductor resistance per meter for the gaugeΩ/m
L_total
total conductor length, feed plus returnm
51

Try it

A
V
%
°F

Hot engine bays raise copper resistance about 0.4% per °C.

Result

Smallest AWG: 10 AWG2.25 %voltage drop
Smallest metric: 4 mm²2.96 %voltage drop

Voltage drop is one check. The wire must also be rated for the current at its temperature and bundling, and the fuse must protect the wire.

Planning estimate from the formula below, not a measurement.

Open the full automotive wire gauge calculator →

Myths vs facts

Myth A wire's current rating is fixed by its gauge.

Fact Ampacity depends on insulation temperature rating, ambient temperature and how many wires are bundled together. The same gauge carries less current inside a hot, tightly wrapped engine harness than alone in free air.2

Myth If the wire does not get hot, it is big enough.

Fact A wire can stay cool and still drop too much voltage over a long run, starving pumps and motors. Check voltage drop at full load as well as temperature.Medium51

Frequently asked

What gauge wire do I need for 20 amps at 12 V?

It depends on run length, insulation and bundling, not just current. Short runs at 20 A commonly use 12 AWG (3.3 mm²); longer runs may need 10 AWG to keep voltage drop reasonable. Calculate drop from current, resistance per meter and the total out-and-back length, and check the cable maker's ampacity table.Medium125

How does wire length affect wire gauge?

Resistance rises in proportion to length, so voltage drop rises with it. A load that runs fine on 14 AWG at 1 m may lose too much voltage at 5 m. Count both the feed and the ground return in the length, and move up a gauge size when drop at full current is too high.51

What is the difference between TXL and GXL wire?

Both are cross-linked polyethylene automotive cables covered by SAE J1128. GXL has a thicker insulation wall and TXL a thin wall, so TXL is lighter and smaller for the same conductor, which suits dense harnesses. Both handle higher temperatures than general-purpose PVC cable.Medium3

How do you convert AWG to mm²?

Use a conversion table rather than a rule of thumb, because the relationship is logarithmic. Common equivalents are 18 AWG at about 0.82 mm², 16 AWG at 1.31 mm², 14 AWG at 2.08 mm², 12 AWG at 3.31 mm² and 10 AWG at 5.26 mm². Metric cable is sold in nearby standard sizes.1

Does the fuse protect the wire or the load?

The wire. A fuse is chosen so it opens before the smallest conductor in its circuit overheats, and it is placed near the power source so a short anywhere downstream is covered. Some loads have their own internal protection, but that does not protect the harness feeding them.Medium72

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. American wire gauge · Wikipedia · reference · retrieved 2026-10-27
  2. Ampacity · Wikipedia · reference · retrieved 2026-10-27
  3. SAE J1128: Low Voltage Primary Cable · SAE International · standard · retrieved 2026-10-27
  4. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  5. Voltage drop · Wikipedia · reference · retrieved 2026-10-27
  6. US 7,774,125: Programmable fuel pump control · US Patent and Trademark Office · reference · retrieved 2026-10-27
  7. Fuse (electrical) · Wikipedia · reference · retrieved 2026-10-27