GAINS PDM2 · Gearboxes

PDM2 · gearbox control

Every gear.

Automatics, manuals, dual-clutch and sequentials, for the swaps you actually build.

PDM2 is planned to control the gearbox as well as the car's power, alongside ECU2: shift solenoids and line pressure on the electronic automatics, the factory TCU over CAN on the dual-clutch units, and reverse lockouts and trans-brakes on the rest. Search by gearbox or by the engine you are swapping.

Planned. No gearbox is supported until bench and vehicle logs and an engineering review say so.

Dual-clutch swaps

DSG and M DCT, without the extra box.

Dual-clutch swaps today mean an engine ECU plus a separate DCT controller box (published prices around $1,400 to $2,100). ECU2 + PDM2 are planned to control the factory DSG and M DCT units directly over CAN, with the shift cut and blip coming from the engine controller itself.

24 of 24
GM · Automaticv1 target

4L60E

The most-swapped electronic automatic behind the LS. PDM2 is planned to run it directly: shift solenoids, line pressure and converter lock-up, with ECU2 supplying torque and throttle.

Swaps: GM LS · GM LT
Direct control4 speeds
GM · Automaticv1 target

4L80E

The heavy-duty GM automatic for big power and towing. PDM2 is planned to run it directly, with both speed sensors, line pressure and converter lock-up.

Swaps: GM LS · GM LT and big-block
Direct control4 speeds
GM · Automaticv2

6L80

Six speeds behind a late LS, controlled through its own TEHCM. PDM2 is planned to provide the engine-side CAN messages the factory unit needs.

Swaps: GM LS3, L92, L99, LY6
CAN to the factory TCU6 speeds
GM · Automaticv2

8L90 and 10L80

Eight and ten speeds behind a Gen V LT. Planned for v2, through the factory TCU over CAN.

Swaps: GM LT1, L83, L86, L84, L87
CAN to the factory TCU10 speeds
Ford · Automaticv1 target

4R70W

Ford's electronic four-speed for Mod-motor and budget Coyote swaps. PDM2 is planned to run it directly.

Swaps: Ford 4.6 / 5.4 Modular and Coyote 5.0
Direct control4 speeds
Ford · Automaticv1 target

4R100 and E4OD

The heavy-duty Ford four-speed. Same control pattern as the 4R70W; planned for direct control.

Swaps: Ford big-block, 7.3 Power Stroke, Godzilla 7.3
Direct control4 speeds
Ford · Automaticv1 target

6R80

Six speeds behind a Coyote. PDM2's eight current-controlled solenoid channels are sized for direct control, with CAN to the factory TCU as the alternative.

Swaps: Ford Coyote 5.0 Gen 1 and Gen 2
Direct control6 speeds
Ford · Automaticv2

10R80

Ten speeds behind a late Coyote. Planned for v2 through the factory TCU over CAN; direct control later.

Swaps: Ford Coyote Gen 3 / 3.5 / 4
CAN to the factory TCU10 speeds
Ford · Automaticv1 target

5R110W

Ford's heavy-duty five-speed. Planned for direct control on PDM2's current-controlled solenoid channels.

Swaps: Power Stroke 6.0 / 6.4, V10, big gas V8s
Direct control5 speeds
Toyota / Aisin · Automaticv1 target

A340E

The usual automatic behind a swapped JZ. Simple on/off solenoids, planned for direct control.

Swaps: Toyota 1JZ and 2JZ
Direct control4 speeds
Tremec · Manualv1 target

T56 and TR6060

The go-to six-speed manual for LS and Coyote swaps. PDM2 runs the reverse lockout and skip-shift solenoids that otherwise need a separate module or a hack.

Swaps: GM LS / LT · Ford Coyote and Mod-motor
Interlocks and switches6 speeds
Tremec · Manualv1 target

T56 Magnum

The aftermarket six-speed built for swaps. PDM2 handles its reverse lockout and speed signal.

Swaps: GM LS / LT, Ford Coyote, Mopar Hemi
Interlocks and switches6 speeds
Getrag / Tremec (Ford) · Manualv1 target

MT82 and TR3650

The Coyote-era Mustang six-speeds. No solenoids; PDM2 reads the switches and speed for ECU2's interlocks.

Swaps: Ford Coyote 5.0 and 4.6 3V
Interlocks and switches6 speeds
Toyota / Aisin · Manualv1 target

R154 and W58

The classic manuals behind a swapped JZ. PDM2 reads the switches and speed signal for ECU2.

Swaps: Toyota 1JZ / 2JZ
Interlocks and switches5 speeds
VW / Audi · Dual-clutchv1 target

DQ250 DSG

The most-swapped DSG. Today a DQ250 swap means an engine ECU plus a separate DSG controller box; ECU2 + PDM2 are planned to run it with no extra box, through the factory mechatronic over CAN.

Swaps: VW / Audi 1.8T, 2.0T and VR6 · Honda K-series and other transverse fours
CAN to the factory TCU6 speeds
VW / Audi · Dual-clutchv1 target

DQ500 DSG

The seven-speed DSG for big power. Planned for v1 alongside the DQ250, through the factory mechatronic over CAN.

Swaps: Audi 2.5 TFSI, big-turbo 2.0T, VR6 turbo
CAN to the factory TCU7 speeds
Getrag (BMW) · Dual-clutchv1 target

BMW M DCT (GS7D36SG, E9x M3)

The dual-clutch swap of choice in time attack, now with adapter kits for LS, K, VQ, JZ and rotary. Planned for v1 through the factory TCU over CAN, so no separate DCT controller box.

Swaps: GM LS · Honda K24, Nissan VQ37, Toyota JZ, Mazda 13B
CAN to the factory TCU7 speeds
Getrag (BMW) · Dual-clutchv2

BMW M DCT gen 2 (F80 / F82 M3 / M4)

The newer M DCT, rising fast in time attack. Planned for v2 after the gen 1 unit.

Swaps: GM LS / LT, Toyota 2JZ, BMW S55 / S58
CAN to the factory TCU7 speeds
Nissan · Dual-clutchLater

Nissan GR6 (R35 GT-R)

The GT-R transaxle. Harder than the VW and BMW units because of its torque-request loop; on the roadmap.

Swaps: Nissan VR38 and transplants
CAN to the factory TCU6 speeds
Porsche (ZF) · Dual-clutchLater

Porsche PDK

PDK for 911 restomods and kit cars. On the roadmap after the VW and BMW units.

Swaps: Porsche flat-six and transplants
CAN to the factory TCU7 speeds
Getrag (Mitsubishi) · Dual-clutchLater

Mitsubishi TC-SST (Evo X)

Mostly an Evo X keep-the-gearbox case rather than a swap. Later.

Swaps: Mitsubishi 4B11T
CAN to the factory TCU6 speeds
Quaife, Holinger, Sadev, Samsonas, Albins and others · Sequentialv1 target

Sequential gearboxes

Paddle shift for any sequential, with one gearbox-agnostic controller. ECU2 does the cut and blip; PDM2 runs the actuator and reads the barrel.

Swaps: Any engine ECU2 runs
Direct control
GM / Ford · Non-electronic automaticv1 target

TH400, TH350, Powerglide and C4

The drag-race classics. Nothing to shift electronically; PDM2 runs the trans-brake and line-lock and ECU2 handles launch.

Swaps: GM LS and small-block, Ford small-block and Coyote
Interlocks and switches
ZF · AutomaticLater

ZF 6HP and 8HP

Excellent eight-speeds with a sealed factory controller. Planned as a partner-TCU integration later, not direct control.

Swaps: BMW, GM LS / LT, Toyota JZ, Cummins
Partner TCU8 speeds
How PDM2 controls them

Four routes,
one box.

Direct control

PDM2 drives the shift, pressure and converter solenoids itself and reads the speed sensors, range switch and fluid temperature.

CAN to the factory TCU

The factory TCU stays. PDM2 sends the engine-side messages it expects (torque, rpm, pedal, brake) on a private gearbox bus and reads gear and status back.

Partner TCU

A specialist standalone TCU runs the gearbox. GAINS talks to it over CAN using the maker's published protocol.

Interlocks and switches

No TCU needed. PDM2 runs the reverse lockout, skip-shift and reverse-light circuits and reads the speed sensor.

Shift logic acts on engine output, so it carries guardrails: per-gear limits, cut timeouts, plausibility checks against ECU2 and a defined failsafe if the link drops. Factory TCUs keep their own calibration; GAINS never flashes or unlocks a third-party module. Brand and model names identify compatible equipment only; GAINS is not affiliated with their makers.

Tell us your swap.

Waitlist answers decide which gearboxes we bench first.

Join the waitlist