How it works
Conventional wiring uses a fuse to protect each circuit and a relay to switch it.
A PDM replaces both with semiconductor switches. Bosch describes its PowerBox as an intelligent control and distribution unit that can replace all conventional relays, fuses and circuit breakers.1
Each output measures current continuously. If current exceeds a programmed limit, the output switches off and can retry. That allows trip points suited to each load, inrush allowances for motors and lamps, and fault logging.Medium12
Capacity varies widely. Bosch's PBX 190 data sheet lists 52 outputs, channel ratings up to 40 A (80 A paralleled), a recommended 250 A continuous total and Ethernet, CAN and LIN communication.1
Inputs such as switches and sensors, plus CAN messages from the engine controller, drive output logic. A fuel pump can run only while the engine controller requests it, and a fan can follow coolant temperature with PWM speed control.Medium13
In tuning
PDMs share data with the engine controller.
Common uses are fuel pump priming and shutoff, staged cooling fans, water pump speed and load shedding at low voltage. Agree on CAN message definitions between devices before wiring.Medium13
Safety note
The main feed to a PDM carries very high current. It still needs correctly sized cable and its own fuse or breaker near the battery, plus a master cutoff where rules require one. Size each output wire for its current and run length.Medium41
Formula and worked example
I = P / V
- I
- load currentA
- P
- load powerW
- V
- system voltageV
Try it
Result
Voltage drop is one check. The wire must also be rated for the current at its temperature and bundling, and the fuse must protect the wire.
Planning estimate from the formula below, not a measurement.
Myths vs facts
Myth A PDM removes the need for any fuses.
Fact Outputs protect themselves, but the main battery feed to the PDM still needs its own overcurrent protection.Medium4
Myth Any PDM channel can drive any load.
Fact Each channel has its own continuous and peak rating. High-current loads may need a higher-rated channel or paralleled outputs.1
Frequently asked
What does a PDM do in a race car?
It powers and protects every electrical load from one programmable unit. Instead of relays and fuses, solid-state outputs switch fuel pumps, fans, lights and controllers, measure current, shut off faulty circuits and log faults. Logic and CAN messages let it react to engine data, such as staging fans by coolant temperature.1
PDM vs fuses and relays: which is better?
Fuses and relays are cheap, simple and easy to repair anywhere. A PDM costs more but saves weight and wiring, gives adjustable trip points, retries, soft starts and diagnostics, and integrates with other controllers. For simple street builds, conventional parts are often enough; complex race wiring benefits most from a PDM.Medium12
How is a PDM controlled?
Through its own inputs and messages from other modules. Switch and sensor inputs connect directly, and CAN or other networks carry requests from the engine controller, dash or keypad. Configuration software sets each output's current limits, logic conditions and PWM behavior. Bosch configures its PowerBox through its PBX Suite software.13
Do I need a PDM?
Not necessarily. A PDM helps most on cars with many electrical loads, a full rewire, or a need for diagnostics and programmable logic, as in motorsport. A road car with a factory harness can usually keep its fuse box. Either way, wire gauge and main feed protection must match the loads.Low14
Used in these guides
- 2JZ Swap BMW E46 3 Series (1999-2006): 2JZ-GTE and 2JZ-GE Guide
- IS300 2JZ-GTE Swap (XE10, 2001-2005): Turbo 2JZ Guide
- MK3 Supra 2JZ Swap (A70, 1986.5-1993): 2JZ-GTE and 2JZ-GE Guide
- Early Bronco Coyote Swap (1966-77): Mounts, 6R80 and Dana 20 Adapters, Fuel, Ford Performance Control Pack and Legal Guide
- Coyote Swap Dentside F-100 / F-150 (1973-79): Mounts, Fuel, Wiring and Legal Guide
- Coyote Swap Fox Body Mustang (1979-93): Mounts, Fuel, Wiring and Legal Guide
- Coyote Swap SN95 and New Edge Mustang (1994-2004): Controls, K-Member, Fuel and Legal Guide
- Hemi Swap Jeep Wrangler TJ (1997-2006): Mounts, Transmission, Transfer Case and Legal Guide
- CRX K Swap and Civic EF (1988-91): K20 and K24 Swap Guide
- E30 LS Swap: Mount Kits, Oil Pan, T56 or ZF, Differential, Brakes and Legal Guide
- 3rd Gen Camaro LS Swap (1982-92): Mounts, K-Member, Oil Pan, Torque Arm, T56 and Fuel Guide
- C4 Corvette LS Swap (1984-96): Mounts, 4+3 vs ZF6 vs 4L60E, Digital Dash, VATS, ABS and Legal Guide
- G-Body LS Swap (1978-88): Mounts, Crossmember, Oil Pan, Steering Box, 7.5 in Rear and EFI Fuel Guide
- OBS LS Swap (1988-1998 C/K, Tahoe, Yukon, Suburban): Mounts, 4L60E/4L80E, Fuel, Gauges, ABS and Legal Guide
- S10 LS Swap (1982-2004): Mounts, Headers, Crossmembers, Oil Pan, Steering Shaft and Legal Guide
- 240Z LS Swap: Mounts, Crossmember Kits, T56, R200 Diff, Chassis and EFI Fuel Guide
- Fox Body LS Swap (1979-93): K-Members, Mounts, Oil Pan, T56 and TKX, Fuel, Ford Cluster Wiring and Legal Guide
- Ford Ranger LS Swap (1983-2011): Mounts, Oil Pan, Transmission, PATS, Speedometer, Fuel and Legal Guide
- G35 LS Swap (V35, 2003-2007): Sedan and Coupe Kits, CD009 or T56, Driveshaft, CAN Gauges, Automatics and Legal Guide
- Jeep Cherokee XJ LS Swap (1984-2001): Unibody Mounts, Low-Hood Intake, AW4 Replacement, NP231/NP242 Adapters, Fuel and Legal Guide
- Jeep Wrangler LS Swap (TJ 1997-2006 and JK 2007-2018): Mounts, Transfer Case Adapters, Fuel, CAN Bus Integration and Legal Guide
- RX-8 LS Swap (SE3P, 2004-2011 US): Mounts, PPF Delete, Steering Rack, Differential, CAN Gauges and Legal Guide
- 300ZX LS Swap (Z32, 1990-1996): Mounts, Z32 5-Speed or T56, HICAS, Gauges, Differential and Legal Guide
- 350Z LS Swap (Z33): Engines, Mounts, CD009 or T56, Wiring, Gauges and Legal Guide
- 944 LS Swap (1982-91): Kits, Transaxle, Clutch Adapter, Oil Pan and Legal Guide
- Tacoma LS Swap (1995-2004): Mounts, 4x4 Transfer Case Adapters, Transmissions, Oil Pan and Legal Guide
- Volvo 240 LS Swap (1975-93): Mounts, Oil Pan, T56, Two-Piece Driveshaft, Rear Axle, Fuel and Legal Guide
- C3 Corvette LT1 Swap (1968-82): Gen V LT1 and LT4 Mounts, Fuel, Transmission and Legal Guide
- RB26DETT Swap Nissan 240SX S14 (1995-98): RWD Conversion, Mounts, Gearbox and Import Guide
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- PowerBox PBX 190 data sheet 75077387 · Bosch Motorsport · vendor-doc · retrieved 2026-10-25
- Solid-state relay · Wikipedia · reference · retrieved 2026-10-25
- CAN bus · Wikipedia · reference · retrieved 2026-10-25
- Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-25

