MK3 Supra 2JZ Swap (A70, 1986.5-1993): 2JZ-GTE and 2JZ-GE Guide

A MK3 Supra 2JZ swap is one of the most common upgrades for the A70, because Toyota already fitted the closely related 1JZ-GTE in the Japanese JZA70. It takes JZ engine brackets, a rear-sump oil pan, a JZ-to-R154 bellhousing or JZ automatic, and a merged harness. The main hurdles are the oil pan, mounts and wiring.Medium2812

Difficulty2/5 · EasyMedium281213
  • Toyota built the A70 with the 1JZ-GTE in Japan, so JZ mounts, bellhousings and the R154 already have a factory path.
  • The oil pan must be a rear-sump JZ pan; front-sump pans from Aristo donors hit the crossmember.
  • Engine brackets differ between early square-mount and late round-mount subframes.
  • The 7M chassis harness must be merged with the JZ engine harness, and gauges, power steering and A/C need small adaptations.

At a glance

The key numbers and parts, with the source on each tile.

Factory sister pathJapan-only JZA70 used the 1JZ-GTE 2.5 L twin turbo (1990-1993)Sourced · medium23
Original engines
ItemPowerTorque
7M-GE200 hp149 kW—
7M-GTE232 hp173 kW254 lb-ft344 Nm
Sourced · medium2
Toyota ratings (Japan, 1993)
ItemPowerTorque
2JZ-GTE280 PS276 hp · 206 kW44.0 kg-m318 lb-ft · 431 Nm
2JZ-GE225 PS222 hp · 165 kW—
Wikipedia lists 320 hp (239 kW) for the export Supra Turbo.Sourced1
Oil pan
  • Rear-sump JZ pan required
  • The A70 is a rear-sump chassis
Sourced814
Factory gearboxesW58 (NA), R154 (turbo) or A340E four-speed automaticSourced · medium26
R154 with a 2JZ
  • Needs the 1JZ-GTE R154 bellhousing and 1JZ flywheel
  • Use the Supra R154, not the Soarer version
Low confidence12
SuspensionDouble wishbone front and rear on all A70 modelsSourced · medium2
Bore and stroke2JZ 86 x 86 mm (2,997 cc) vs 7M 83 x 91 mm2,954 ccSourced · medium34

Recommended engines

  • 2JZ-GTE (non-VVT-i) · The 1993-97 twin-turbo engine Toyota rated at 280 PS (276 hp, 206 kW) in Japan; no cam phasing to control, so wiring and calibration are simpler than the VVT-i version.
  • 2JZ-GTE VVT-i · Adds VVT-i intake cam phasing from 1997; often sourced from the Japanese Aristo, which arrives with a front-sump pan that must be swapped for a rear-sump pan in the A70.
  • 2JZ-GE (NA, VVT-i 1998+) · The naturally aspirated 2JZ is cheaper and widespread; it shares its block, crankshaft and rods with the GTE, so many MK3 owners start here and add a turbo later.

Mounts

A MK3 Supra 2JZ swap starts from a factory precedent.

Subframe types

Square-mount (1986.5 to early 1989) and round-mount (late 1989 to 1992)

Low confidence1213
OEM JZ brackets1JZ brackets reported to fit round-mount subframes onlyLow confidence1213
Source of correct partsJZA70 1JZ brackets and bellhousing, as Toyota fitted themLow confidence142

Toyota built the Japan-only JZA70 with the 1JZ-GTE, and the 2JZ shares the 1JZ's bore pitch and general architecture. That means JZ brackets and mount positions already exist for the A70 body, unlike most chassis that need fabricated mounts.Medium23

Check which subframe your car has first. A widely used owner guide splits A70s into square-mount cars (1986.5 to early 1989) and round-mount cars (late 1989 on). OEM 1JZ brackets reportedly fit only the round type, and MK4 rubber mounts can work there once a tab is ground off.Low1213

Transmission

R154
  • Fitted to the 1987-1992 MA70 7M-GTE in the US
  • Also used behind 1JZ-GTE engines in Japan
Sourced · medium5
R154 ratios3.251 / 1.955 / 1.310 / 1.000 / 0.753, reverse 3.180Sourced · medium5
A340E
  • Fitted to the MA70, SC300 and JZA80
  • A heavy-duty variant was used behind the 1997-2002 2JZ-GTE
Sourced · medium7
V160Getrag Type 233 six-speed, the factory 2JZ-GTE manualSourced · medium3
CD009 adapter
  • Reuses the J3 automatic bellhousing (J2 will not work)
  • Needs a hydraulic release bearing and 3/4 in master cylinder
Sourced9

The R154 five-speed is the usual MK3 choice because turbo cars already have one, along with the right crossmember and shifter location. The 7M bellhousing does not bolt to a JZ, so owners fit the 1JZ-GTE R154 bellhousing and a 1JZ flywheel, which also fit the 2JZ. A 1986.5-1992 7M-GTE clutch is reported to fit.Low125

Use a Supra R154 rather than a Soarer unit. Wikipedia lists several shifter housing styles on two non-interchangeable base patterns, and the owner guide reports the Soarer housing sits too long for the A70 console. Non-turbo W58 cars can swap to an R154 with the turbo crossmember parts.Medium512

Automatic cars keep an A340E but need a JZ automatic bellhousing, such as an SC300 or 2JZ-GTE unit; Wikipedia notes the 1997-2002 twin-turbo Supra used a heavy-duty A340E. The V160 six-speed is the factory 2JZ-GTE pairing, a CD009 adapts with a plate that reuses the J3 automatic bellhousing, and one featured MK3 build used a T56.Medium1373911

Clearance

The oil pan is the hard clearance point.

Oil pan
  • Front-sump pans hit the crossmember
  • The A70 needs a rear-sump pan
Sourced815
Stock twin turbos

One owner estimates 1/2 to 1 1/2 in (13-38 mm) of firewall dressing to keep the factory twins

Low confidence13

XAT Racing lists the Mk3 Supra A70 among rear-sump chassis, and owners report a front-sump pan sits where the crossmember is. Many imported 2JZ-GTE engines come from the Aristo, which has a front sump, so plan to buy or swap a full rear-sump pan set.Medium81513

The 2JZ is taller than a 1JZ because of its taller deck and longer rods for 14.5 mm (0.57 in) more stroke. Check hood clearance with the intake manifold fitted. Keeping the sequential twin turbos may also need firewall dressing; one owner estimates 1/2 to 1 1/2 in (13-38 mm).Low313

On the left side, the JZ moves the power steering pump and alternator compared with the 7M. Plan new hose and cable routes, and check the steering shaft and brake lines against exhaust heat before final assembly.Low1216

Cooling

A 2JZ-GTE rated at 280 PS (206 kW) in Japan rejects more heat than the 7M-GTE that Wikipedia lists at 232 hp (173 kW).

Heat load

2JZ-GTE rated 280 PS (206 kW) in Japanese trim, vs 232 hp (173 kW) for the 7M-GTE

Sourced12
Pulleys

Aristo hydraulic-fan pulleys differ from US Supra water pump pulleys

Low confidence13

Fit a larger aluminum radiator, a correct shroud and either a fan clutch or electric fans sized for the job. Add an oil cooler for track use.Medium12

Aristo donors often carry a hydraulically driven fan. Owners report using a 2JZ-GTE water pump and rear housing without the hydraulic pump, and note that the Aristo pulleys differ from US Supra parts. Fit new water neck O-rings and a thermostat while the engine is out.Low1213

Turbo cars need an intercooler and charge pipes. Owners suggest 2.5 in (64 mm) piping for twins and 3 in (76 mm) for single-turbo builds, with good clamps and silicone joints. Bleed air at the highest point and never open a hot cooling system.Low1213

Fuel

Wikipedia lists 550 cc/min injectors on the export 2JZ-GTE and 440 cc/min on the Japanese engine.

Factory injectors (GTE)
  • 550 cc/min export
  • 440 cc/min Japan
Sourced · medium3
Compression
  • 7M-GTE 8.4:1
  • 7M-GE 9.1:1
Sourced · medium4

Size injectors and the in-tank pump for the power you plan, not the stock figures. Owners commonly fit a higher-flow in-tank pump and improve its power feed.Medium312

Owners commonly upgrade the in-tank pump and its power feed rather than replacing the whole system. Check the condition of the hoses, filter and sender before reuse, and plan substantially more flow if you intend to run E85.Low12

Exhaust

Wikipedia lists sequential twin turbos on the 2JZ-GTE: CT20 units in Japan and CT12B units for export.

Factory turbosSequential twins: CT20 (Japan), CT12B (export)Sourced · medium3
1JZ-GTE in the JZA70Twin CT12A turbosSourced · medium3

The sequential system adds valves and vacuum controls, and owners report it may need firewall dressing in the A70. Many MK3 builds switch to a single turbo and new manifold for packaging.Medium313

A custom downpipe and exhaust are normal because the 7M parts do not match the JZ outlet. Route the downpipe clear of the steering shaft and floor, add heat shielding near brake lines and wiring, and leave a wideband oxygen sensor bung after the turbine.Low13

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads
Chassis harness
  • 7M body plugs vary by year
  • Owners merge the 7M chassis side with a JZ engine harness
Low confidence1213
Alternator
  • Moves to the passenger side
  • Battery cable must be extended
Low confidence12
Gauges
  • Cluster temperature gauge reads a single-pin sender
  • ECU uses a separate two-pin sensor
Low confidence12

The engine needs power and grounds, crank and cam signals, injector and ignition outputs, throttle position, load sensing, temperature sensors, knock sensors and an oxygen sensor. VVT-i engines add an oil control valve and cam feedback. Owners usually merge the 7M body plugs, which vary by year, onto a JZ engine harness.Low12133

Keep the A70 gauges alive. The owner guide reports the cluster temperature gauge reads a single-pin sender while the engine computer uses a separate two-pin sensor, and that a remote line can feed the 7M oil pressure sender. You also need a tach signal, fan control and fuel pump control.Low12

A standalone engine computer is best mounted in the cabin, such as the passenger kick panel or behind the glovebox, away from heat and water. A power distribution module (PDM) can replace separate relays for the pump, fans and ignition feeds, or use fused relays. Fuse every feed at the source and size wire for the load.Low12

Chassis

LSD

Sports package with limited-slip differential standard on turbo models

Sourced · medium2
Torque

2JZ-GTE rated 44.0 kg-m (318 lb-ft, 431 Nm) in Japan vs 254 lb-ft (344 Nm) for the 7M-GTE

Sourced12
Power steering

Braided PTFE pump-to-rack lines are sold for MKIII Supras with 1JZ or 2JZ engines

Sourced10

Turbo A70s came with a sports package that included a limited-slip differential, so the turbo rear end is the better starting point. Toyota's 2JZ-GTE torque rating of 44.0 kg-m (318 lb-ft) in Japan exceeds the 7M-GTE's 254 lb-ft (344 Nm). Inspect the differential, axles and driveshaft joints, and plan brakes that repeat hard stops.Medium21

Power steering can stay. 3SX sells a braided stainless PTFE pump-to-rack line listed for MKIII and MKIV Supras with 1JZ or 2JZ engines, and owners report the pump moves to the other side of the bay versus the 7M. For A/C, the guide reports fitting the 7M compressor head onto the JZ compressor.Medium101612

Driveshaft choice follows the gearbox. Owners report the 1986.5-1992 auto shaft for an A340E and the turbo manual shaft for an R154, though posters disagree on R154 spline fit. Measure with the drivetrain on its final mounts before ordering anything custom.Low1312

Tuning

Most 2JZ swaps run on manifold pressure (speed density) or an airflow meter, depending on the engine computer.

Load sensing
  • The 7M Turbo A used manifold pressure
  • Other 7M engines an airflow meter
Sourced · medium4
Cam controlVVT-i on the intake cam from 1997 (GTE) and 1995 (GE)Sourced · medium3

Start from injector data and displacement, then correct fuel from wideband logs. A Japanese donor computer expects its own sensors, and any turbo, cam or intake change makes a donor map only a starting point.Medium313

Boost needs layered protection

A wastegate sized for the turbo, closed-loop boost control with an overboost cut, and knock monitoring. Advance ignition only as far as knock data supports on your fuel. A standalone computer mounted in the cabin also makes logging and boost control easier to wire.Medium3

Log intake air temperature after the intercooler, lambda, boost, coolant and oil temperature, and knock. On VVT-i engines, log intake cam angle against target and keep idle overlap modest for stable running.Low3

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 22 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning

Order of work

10 stages, in the order most builds follow.

  1. Identify the car
    Confirm model year, subframe mount type, gearbox and whether it is a turbo car with the LSD and R154.
  2. Plan the combination
    Choose engine, gearbox, turbo layout and engine management together, then source brackets, bellhousing and a rear-sump pan.
  3. Prepare the donor
    Check compression, replace the timing belt, water pump and seals, fit the rear-sump pan and a fresh clutch.
  4. Strip the A70
    Remove the 7M, gearbox, intake and exhaust; label the chassis connectors you will merge.
  5. Fit and test
    Install brackets and mounts, lower the engine and gearbox with a load leveler, and check crossmember, firewall and hood clearance.
  6. Driveline and steering
    Fit the driveshaft, clutch hydraulics and power steering line; bleed and check for leaks.
  7. Cooling, fuel and exhaust
    Install radiator, intercooler, pump, injectors and exhaust; pressure-test fuel and coolant.
  8. Wire and start
    Merge the harness, fit fuses, relays or a PDM and gauge senders; prime oil pressure, confirm sync and fuel pressure, then start.
  9. Calibrate
    Build fuel and boost control from wideband logs at low boost first, watching knock and temperatures.
  10. Shake down and register
    Re-torque mounts and driveline, then complete emissions, registration and insurance steps.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Engine will not sit on the crossmemberFront-sump oil pan from an Aristo or other front-sump donorFit a complete rear-sump JZ pan set with matching pickup and dipstick.815
Turbo oil drain has nowhere to goNon-turbo rear-sump pan lacks a finished drain portHave the drain boss drilled and tapped, or use a turbo pan.Low14
OEM JZ brackets do not fitEarly square-mount subframeUse brackets made for the square-mount subframe, or confirm the subframe type before buying.Low1213
Shifter sits in the wrong placeSoarer R154 with a longer shifter housingUse a Supra R154 or a compatible shifter housing on the matching base pattern.Medium125
Temperature or oil pressure gauge reads wrongCluster sender not connected or wrong sender typeFit the single-pin cluster sender and a line to the 7M oil pressure sender.Low12
Fails a California Referee inspectionEngine lacks the emissions controls it was certified withCheck eligibility with a Referee before buying, and fit the donor's emissions controls.18

Frequently asked

What oil pan do I need for a 2JZ in a MK3 Supra?

You need a complete rear-sump JZ oil pan set. XAT Racing lists the Mk3 Supra A70 as a rear-sump chassis, and owners report front-sump pans hit the crossmember. Aristo 2JZ-GTE engines come with a front sump, so swap the upper pan, lower pan, pickup and dipstick before installation.Medium81513

What bellhousing do I need for a 2JZ R154 swap?

Use the 1JZ-GTE R154 bellhousing with a 1JZ flywheel. Toyota paired the R154 with the 1JZ-GTE in Japan, and owners report both parts fit the 2JZ because the JZ engines share the rear pattern. The 7M-GTE bellhousing does not fit. A 1986.5-1992 7M-GTE clutch is reported to fit.Low125

Is a 1JZ or 2JZ better for a MK3 Supra?

The 1JZ-GTE is the factory option, since Toyota fitted it in the Japan-only JZA70, so its brackets and bellhousing are direct. The 2JZ adds 14.5 mm of stroke for 3.0 L and Toyota rated the 2JZ-GTE at 44.0 kg-m (318 lb-ft) in Japan. Most parts are shared, so the 2JZ costs little extra work.Medium231

Does a 2JZ bolt into a MK3 Supra?

Almost, with the right parts. Late round-mount cars accept OEM 1JZ brackets, while early square-mount cars need adapter brackets. You also need a rear-sump pan, a JZ bellhousing for your gearbox, and a merged harness. Expect small jobs such as power steering lines, alternator wiring and gauge senders.Low128

Can I keep power steering and A/C on a 2JZ MK3?

Yes. Braided pump-to-rack lines are sold for MKIII Supras with 1JZ or 2JZ engines, and owners report keeping the factory rack. For A/C, the owner guide reports fitting the 7M compressor head onto the JZ compressor so the 7M lines connect, sometimes with a little bracket notching.Medium1012

Is a 2JZ MK3 Supra street legal?

It can be, depending on location. California requires a BAR Referee inspection, the UK requires a V5C update with evidence, Germany needs an inspector's approval and Australian states apply VSB 14. Imported Japanese engines can complicate US emissions approval. This is general information, not legal advice.Medium18192021

Related

Sources

21 sources
  1. Toyota launches all-new Supra (May 1993 release, 75 Years of Toyota archive) · Toyota Motor Corporation · oem · retrieved 2026-10-25
  2. Toyota Supra (third generation, A70) · Wikipedia · reference · retrieved 2026-10-27
  3. Toyota JZ engine · Wikipedia · reference · retrieved 2026-10-27
  4. Toyota M engine (7M-GE, 7M-GTE) · Wikipedia · reference · retrieved 2026-10-27
  5. Toyota R transmission · Wikipedia · reference · retrieved 2026-10-27
  6. Toyota W transmission · Wikipedia · reference · retrieved 2026-10-27
  7. Toyota A transmission (A340E, A650E) · Wikipedia · reference · retrieved 2026-10-27
  8. JZ Rear Sump Oil Pan Kit (product page, front and rear sump chassis lists) · XAT Racing · vendor-doc · retrieved 2026-10-27
  9. 2JZ Billet CD009 Adapter Plate (product page) · XAT Racing · vendor-doc · retrieved 2026-10-27
  10. Supra / SC Custom Braided Stainless Steel Power Steering Line (product page) · 3SX Performance · vendor-doc · retrieved 2026-10-27
  11. Supra Mk3 with a 2JZ-GTE Inline-Six (December 2021) · Engine Swap Depot · press · retrieved 2026-10-27
  12. Your 1JZ-GTE and 2JZ-GTE swap guide for dummies (MKIII, forum thread, 2012) · Supramania · community · retrieved 2026-10-27
  13. 2JZGTE MKIII Swap Info (forum thread, 2008) · Supramania · community · retrieved 2026-10-27
  14. What oil pan for 89' Supra 2jzgte Swap (forum thread, 2006) · Supramania · community · retrieved 2026-10-27
  15. 2jz oil pan issue (forum thread, 2007) · Supramania · community · retrieved 2026-10-27
  16. 1JZ power steering lines and adapting 7M oil pressure sensor (forum thread) · Supramania · community · retrieved 2026-10-27
  17. Tampering Policy: The EPA Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  18. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-27
  19. Change vehicle details on a V5C: what evidence to give · GOV.UK (DVLA) · standard · retrieved 2026-10-25
  20. Strassenverkehrs-Zulassungs-Ordnung (StVZO) section 19: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  21. Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government, Department of Infrastructure · standard · retrieved 2026-10-25