Speed density

speed-densitySDMAP-based fuelingD-Jetronic

Speed density is an engine-load strategy in which the ECU estimates the air mass in each cylinder from engine speed, manifold absolute pressure and intake air temperature, using a volumetric efficiency table. It replaces a mass airflow sensor with a model of how the engine breathes.12

How it works

The name describes the inputs

Engine speed and air density. Density comes from manifold absolute pressure (MAP) and intake air temperature through the ideal gas law. The ECU multiplies that density by cylinder volume and a volumetric efficiency (VE) value looked up by rpm and MAP to estimate trapped air mass.12

Speed density is an old idea. Bosch D-Jetronic, built from 1967 to 1976, computed fuel from engine speed and manifold pressure, building on Bendix Electrojector patents. Later airflow-meter systems such as L-Jetronic measured air directly, and modern OEM systems often combine both methods.Medium34

Because it infers air from pressure, speed density has no sensor in the intake tract to restrict flow or be upset by reversion. Its weakness is that anything changing the engine's breathing, such as a new cam, intake or exhaust, changes VE and requires the table to be recalibrated.12

Speed density relies on an accurate air temperature input. A sensor heat-soaked by the manifold reads above the true charge temperature, so the model underestimates air density and fueling drifts lean. Sensor placement and temperature-blending logic matter as much as the VE table.Medium15

In tuning

Speed density suits engines with large cams, individual throttles, or boost levels beyond a MAF sensor's range, because MAP stays a usable load signal where airflow meters struggle. It is also common after intake changes that would invalidate a MAF calibration.Medium12

Calibrating speed density means filling the VE table so measured lambda matches target at every rpm and load cell, then checking temperature and barometric corrections. Steady-state cells are tuned on a load-bearing dyno or with logged road data and a wideband sensor.Medium15

Formula and worked example

m_air = VE × (MAP × V_cyl) / (R_air × T_charge)
m_air
air mass trapped per cylinder per cyclekg
VE
volumetric efficiency referenced to manifold conditions (fraction)
MAP
manifold absolute pressurePa
V_cyl
swept volume of one cylinderm³
R_air
specific gas constant of dry air, 287.05J/(kg·K)
T_charge
charge air temperatureK
16

Try it

cu in
rpm
%
psi

14.7 psia at sea level wide-open throttle without boost.

°F

Result

Volumetric airflow541 CFM at manifold conditions
Mass airflow39.0 lb/min

Planning estimate from the formula below, not a measurement.

Open the full engine airflow (cfm) calculator →

Myths vs facts

Myth Speed density cannot handle altitude changes.

Fact MAP is an absolute reading, so a thinner atmosphere shows up as lower manifold pressure and the model reduces fuel automatically. What it may miss is a change in exhaust back-pressure relative to the manifold, which some ECUs correct with a barometric input.12

Myth Speed density is always less accurate than a MAF.

Fact Each has failure modes. A MAF can misread with reversion, turbulence or oil contamination; speed density errs when VE changes or air temperature is misread. A well-calibrated speed-density system is accurate enough for production and racing use.Medium721

Myth A VE table only needs filling at wide-open throttle.

Fact Part-throttle cells cover most driving and govern emissions, idle quality and fuel economy, so every operating cell needs calibration, not just the power curve.Medium15

Frequently asked

Is speed density better than MAF?

Neither is better everywhere. Speed density has no flow restriction and handles big cams, individual throttles and high boost well, but it must be recalibrated when breathing changes. A MAF measures air directly and adapts to modifications, but it can misread with reversion or turbulence and has a maximum flow range.Medium721

What sensors does speed density need?

At minimum it needs an engine speed signal from the crank sensor, a manifold absolute pressure sensor and an intake air temperature sensor. Most systems also use coolant temperature, throttle position for transient fueling, a barometric reading and an oxygen sensor for closed-loop correction.21

Why do people convert from MAF to speed density?

Common reasons are a turbo or supercharger that pushes airflow past the meter's range, a large cam that causes reversion through the meter, or an intake layout with no room for a straight section ahead of the sensor. Each conversion then needs a full VE calibration.Medium71

How does speed density handle intake air temperature?

It uses the ideal gas law: density falls as absolute temperature rises, so the ECU reduces the air estimate in proportion. If the sensor reads metal temperature rather than charge temperature, the correction is wrong, which is why many systems blend intake and coolant temperatures.Medium15

Does speed density need a wideband to tune?

Practically, yes. The VE table is adjusted until measured lambda matches the target in each cell, and only a wideband sensor reads lambda across the rich and lean range used under load. A narrowband sensor only indicates whether the mixture is rich or lean of stoichiometric.8

Wiring, pinouts and parts

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-25
  2. MAP sensor · Wikipedia · reference · retrieved 2026-10-25
  3. Fuel injection · Wikipedia · reference · retrieved 2026-10-25
  4. Jetronic · Wikipedia · reference · retrieved 2026-10-25
  5. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-25
  6. Volumetric efficiency · Wikipedia · reference · retrieved 2026-10-25
  7. Mass flow sensor · Wikipedia · reference · retrieved 2026-10-25
  8. Lambda Sensor LSU 4.9 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-25