K-Swap Mazda Miata NA (1990-97): K24 and K20 Swap Guide

A K-swap Miata is a well-established swap with complete kits that turn a transverse Honda K-series into a longitudinal, rear-drive layout in the 1990-97 NA. It takes a K24 or K20, an adapter plate and flywheel for the Miata gearbox, mounts, a RWD intake and oil pan. The main hurdles are hood clearance, wiring and engine management, and driveline strength.Medium346

Difficulty3/5 · ModerateMedium346
  • The engine was designed for front-drive, so it needs a rear-drive intake manifold, coolant neck, oil pan and an adapter plate and flywheel to meet the Miata gearbox.
  • The K24A2 kit replaces the front subframe with a tubular one, and a K24 is about 0.5 in (13 mm) too tall for the stock NA hood without modified valve covers.
  • Engine management and a full wiring conversion are needed, and the NA's analog gauges need their own signals.
  • Early 1.6 L cars have a smaller ring and pinion that struggled even with Miata power upgrades.

At a glance

The key numbers and parts, with the source on each tile.

Swap ecosystem

Complete NA/NB packages exist for the K24A2 and a lower-cost one for the K24Z3/K24Z7

Sourced · medium34
Recommended engines
  • K24A2 for the full kit
  • K24Z3/K24Z7 for budget
  • K20 for stock-hood fit
Sourced · medium34
Hood clearance
  • K20 clears the stock NA hood
  • A K24 is about 0.5 in too tall without modified valve covers13 mm
Sourced · medium3
Stock car weight

About 2,160-2,210 lb (980-1,002 kg) curb, depending on source and year

Sourced · medium5
K20A weightAbout 275 lb without gearbox125 kgWikipedia figure; no sourced weight found for the stock B6 or BP engine.Sourced · medium2
Stock engine output
ItemPower
B6 1.6115 bhp86 kW
BP 1.8129-133 bhp96-99 kW
Sourced · medium5
K24A2 output
  • Acura rated the TSX K24A2 at 200 hp at launch149 kW
  • Wikipedia lists 205 hp for 2006-08
Sourced · medium2
TransmissionMiata gearbox via a K-to-Miata adapter plate and flywheelSourced · medium3
Differential
  • Viscous LSD optional early
  • Torsen from 1994 in some markets
  • 1.6 cars have the smaller ring and pinion
Sourced · medium56

Recommended engines

  • K24A2 (TSX) · The TSX engine is the one the most complete NA/NB Miata kit is built around, with a tubular subframe, RWD intake manifold and header; it brings 2.4 L of torque at a weight close to the K20.
  • K24Z (K24Z7 Civic Si) · KPower treats the K24Z7 as identical to the K24Z3 for its lower-cost Miata package; it needs a K20 Type S oil pump to fit and is a good base when budget matters more than peak rpm.
  • K20A2 (RSX Type S / EP3 EU Type R) · The shorter K20 clears the stock NA hood where a K24 needs modified valve covers; check that your subframe and mount kit accepts the specific K20 block before buying one.

Mounts

Two kit routes dominate.

K24A2 packageMachined mounts, mount pads and a tubular front subframeSourced · medium3
K24Z3 basic package
  • Machined mounts and pads, oil pan, oil pump adapter, RWD intake and coolant neck
  • No subframe listed
Sourced · medium4
Mount materialPolyurethane mounts that raise noise and vibrationSourced · medium3

KPower's K24A2 package replaces the front subframe with a tubular one and adds machined mounts, and the maker says it keeps the factory Miata steering geometry. Its basic K24Z3 package is the minimum to mount a K24Z3 in a 1990-2005 Miata and does not list a subframe.Medium34

The kit mounts use polyurethane to limit engine movement. KPower warns that this raises noise, vibration and harshness, which matters more in a small roadster with little sound deadening.Medium3

Transmission

The K-series keeps the Miata's rear-drive gearbox.

AdapterK-series to Miata adapter plate and matching flywheelSourced · medium3
Stock NA gearbox5-speed M526 manualSourced · medium5
Clutch release

Hydraulic release bearing with lines listed for 5- or 6-speed in KPower's packages

From the listing summary; confirm with the kit maker.Low confidence4

An adapter plate and K-to-Miata flywheel join the Honda crank to the Mazda bellhousing pattern. The NA left the factory with the 5-speed M526 manual; KPower lists clutch release hardware for 5- and 6-speed Miata gearboxes, so check which your kit supports.Medium345

The K24 makes much more torque than the Miata gearbox was built for. Keep launches and clutch dumps in check, choose a clutch the kit maker recommends, and inspect the gearbox mount and driveshaft bolts after the first drives.Low32

Clearance

Height is the NA's limit.

Hood
  • K24 about 0.5 in too tall for the NA hood13 mm
  • Modified valve covers fix it
Sourced · medium3
Oil pump (K24Z3)K20 Type S oil pump required for the kit to fitSourced · medium4

KPower says a K20 clears the stock hood but a K24 sits about half an inch (13 mm) too tall, which it solves with modified valve covers. Fit the valve covers before deciding on a vented or aftermarket hood.Medium3

Below the engine, the RWD oil pan and pickup set ground clearance and subframe clearance. The K24Z3 package needs a K20 Type S oil pump to fit its pan, so buy the pump with the kit rather than reusing the donor's.Medium4

Cooling

Turning the engine longitudinal moves the coolant outlets away from where the Miata radiator expects them.

Coolant neck

K24A2 package uses a right-side upper neck for easier hose routing

Sourced · medium3
K24Z3Package includes a K24Z3 upper coolant neckSourced · medium4

The kits supply an upper coolant neck for each engine, and KPower moved the K24A2 neck to the right side to simplify the upper hose. Route the lower hose clear of the steering shaft and belts.Medium34

A Miata radiator was sized for about 130 bhp. Plan an aluminum radiator and a fan you can switch from coolant temperature, then confirm temperatures on a hot day and in traffic. Bleed air from the highest point and never open a hot system.Low53

Fuel

Demand

K24A2 rated 200-205 hp (149-153 kW) versus 115-133 bhp (86-99 kW) stock

Sourced · medium25

A K24 at full load uses noticeably more fuel than a 1.6 or 1.8 Miata engine, so check the in-tank pump and lines against the target power. Decide where pressure is regulated, at the rail with a return or at the tank, and set base pressure with a gauge before first start.Low25

Exhaust

The donor header cannot be reused in a longitudinal layout.

HeaderStainless 4-2-1 header in the K24A2 packageSourced · medium3
Upstream sensorTSX uses a linear air/fuel sensor ahead of the catalystSourced1

The K24A2 package includes a stainless 4-2-1 header; from there a downpipe and exhaust run back under the car to the Miata's rear. Leave room for the catalyst if your inspection requires it.Medium3

Add a wideband oxygen sensor bung in the downpipe or collector for calibration. The TSX's own linear air/fuel sensor sits ahead of the catalyst, so keep a matching position if you reuse factory-style closed loop.Medium1

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads
Engine sensors

Throttle position, temperatures, manifold and barometric pressure, air/fuel, crank and both cams

Sourced1
ThrottleKPower offers both cable and drive-by-wire throttle body optionsSourced · medium3
Wiring

A Miata conversion harness is sold separately from the K24A2 package

Sourced · medium34

The engine needs signals and drive for its crank and two cam sensors, injectors, ignition coils, VTEC solenoid and VTC oil control valve, plus throttle position, manifold pressure, temperatures and the air/fuel sensor. Whatever runs the engine must handle all of these and join the Honda harness to the Miata chassis.1

Choose cable or drive-by-wire throttle up front. KPower sells both throttle body options, and a drive-by-wire setup needs an electronic pedal and a controller that runs the throttle safely. Plan fuel pump relay control, any immobilizer link the donor computer expects, A/C and radiator fan control.Medium34

The NA has analog gauges, so it needs a tachometer signal, a coolant sender the gauge reads, an oil pressure sender and the check-engine lamp. Fuse each new circuit at the source, size wire for the load and relay the pump, fans and main power.Low5

Chassis

The rear end is the weak point on early cars.

Differential history

Smaller ring and pinion on early 1.6 cars caused problems even before swaps

Sourced · medium6
LSD options
  • Viscous LSD optional
  • Torsen offered from 1994 in Japan and the US
Sourced · medium5

Keith Tanner of Flyin' Miata told Jalopnik that the smaller ring and pinion caused issues on early 1.6 Miatas, so plan on the larger 1.8 rear end, with its Torsen option from 1994, behind a K-series.Medium65

Brakes, axles and tires sized for 115-133 bhp now see far more power. Upgrade pads, fluid and lines at minimum, and check the half-shafts and driveshaft for play after the first hard drives.Low52

Tuning

Honda's K24A2 computer uses manifold pressure to estimate load and an air/fuel sensor to trim fuel.

Factory load strategySpeed density from manifold pressure on the K24A2Sourced1
New intake

RWD intake manifold replaces the donor's, so airflow differs from the factory map

Sourced · medium34

The swap replaces the intake manifold and exhaust, so volumetric efficiency changes. Build the fuel table from wideband logs rather than trusting a donor map.Medium13

Set the VTEC crossover where both cam profiles make equal torque and choose cam phasing from logged results. Advance ignition only as far as knock monitoring and the logs support; there is no single safe figure for every engine and fuel.Medium2

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 24 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Choose the kit route
    Pick the engine and kit together: full K24A2 package with tubular subframe, or a basic K24Z3 package. Decide cable or drive-by-wire throttle.
  2. Prepare the engine
    Check compression and leak-down, fit the RWD oil pan, pickup and required oil pump, intake manifold and coolant neck on the stand.
  3. Fit the adapter and flywheel
    Bolt the adapter plate, flywheel and clutch to the engine and check release bearing travel.
  4. Strip the Miata
    Remove the engine, gearbox, front subframe if replacing it, and engine-bay wiring and hoses. Label everything.
  5. Install subframe and mounts
    Fit the subframe and mounts, then lower the engine and gearbox on a hoist with a load leveler and torque to the kit maker's figures.
  6. Check clearances
    Confirm hood, steering shaft, brake lines and ground clearance with the suspension compressed.
  7. Plumb cooling, fuel and exhaust
    Fit radiator and hoses, fuel supply and regulator, header and downpipe; pressure-test fuel and coolant.
  8. Wire and start
    Connect engine harness, chassis conversion, pedal, gauges and relays; prime oil pressure, confirm sync and start.
  9. Calibrate and shake down
    Fit a wideband, build tables from logs, then re-torque mounts, driveline and subframe after the first drives.
  10. Register
    Complete emissions, registration and insurance steps for your region.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Hood will not closeK24 is about 0.5 in (13 mm) too tall for the stock NA hoodFit modified valve covers or a hood with clearance; a K20 clears the stock hood.Medium3
K24Z3 oil pan will not fitDonor K24 oil pump left in placeFit a K20 Type S oil pump as the kit requires.Medium4
Cabin buzz and vibrationPolyurethane engine mounts transmit more vibrationExpect some increase; check mounts are not bottoming and exhaust hangers are not loaded.Medium3
Rear differential failure on a 1.6 carEarly 1.6 cars use a smaller ring and pinionSwap in a 1.8 rear end, ideally with a limited-slip differential.Medium65
Fuel map far off after first startRWD intake and header change airflow versus the donorBuild the volumetric efficiency table from wideband logs instead of reusing a donor map.Medium31
Fails a California Referee inspectionEmissions equipment from the donor configuration missing or disconnectedFit and connect the donor's emissions controls; the Referee tests to the donor vehicle's smog requirements.8

Frequently asked

Does a K24 fit under the NA Miata hood?

Not with stock valve covers. KPower says a K24 sits about 0.5 in (13 mm) too tall for the NA hood and sells modified valve covers to make it fit. A K20 clears the stock hood, which is one reason some builders choose the shorter engine.Medium3

What transmission does a K-swap Miata use?

It keeps a Miata gearbox. An adapter plate and a K-to-Miata flywheel join the Honda engine to the Mazda transmission. The NA came with the 5-speed M526, and KPower lists clutch release hardware for 5- and 6-speed Miata gearboxes, so confirm which your kit supports.Medium345

K24A2 or K24Z3 for a Miata swap?

The K24A2 has the more complete kit, including a tubular subframe and header, and Acura rated it at 200 hp (149 kW) at launch. The K24Z3 route is a lower-cost basic package that needs a K20 Type S oil pump. Choose by budget and how much you want pre-engineered.Medium342

Will the stock Miata differential hold a K24?

The 1.6 rear end is the risk. Flyin' Miata's Keith Tanner told Jalopnik the smaller ring and pinion caused issues on early 1.6 cars. Most builders fit the larger 1.8 rear end, and Mazda offered a Torsen limited-slip from 1994 in some markets.Medium65

How much heavier is a K-swapped Miata?

No reliable published figure compares the two engines installed. Wikipedia lists a K20A at about 275 lb (125 kg) without gearbox and an NA Miata at roughly 2,160-2,210 lb (980-1,002 kg) curb. Weigh the car on scales before and after if balance matters.Medium25

Is a K-swapped Miata street legal?

It can be, depending on location. California requires a BAR Referee inspection against the donor vehicle's smog rules, the UK requires a V5C update with evidence, Germany needs an inspector's approval and Australian states apply VSB 14. This is general information, not legal advice.Medium891011

Related

Sources

11 sources
  1. 2004 Acura TSX Powertrain (press release, part 2) · American Honda Motor Co. (Acura) · oem · retrieved 2026-10-25
  2. Honda K engine · Wikipedia · reference · retrieved 2026-10-25
  3. KPower K24A2 Miata swap package V3 (product listing) · KPower Industries (listing by Tegiwa) · vendor-doc · retrieved 2026-10-25
  4. KPower K24Z3 Miata basic swap package (product listing) · KPower Industries (listing by Tegiwa) · vendor-doc · retrieved 2026-10-25
  5. Mazda MX-5 (NA) · Wikipedia · reference · retrieved 2026-10-25
  6. Of Course Flyin' Miata Will Stick A V8 Into The New Miata · Jalopnik · press · retrieved 2026-10-25
  7. Tampering Policy: The EPA Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  8. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  9. Change vehicle details on a V5C: what evidence to give · GOV.UK (DVLA) · standard · retrieved 2026-10-25
  10. Strassenverkehrs-Zulassungs-Ordnung (StVZO) section 19: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  11. Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government, Department of Infrastructure · standard · retrieved 2026-10-25