Factory specification
Layout, dimensions and factory hardware, each with its source.
Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.
K24A2 firing order
K24A2 injectors
The factory injector, then direct-fit upgrades the makers list for this engine.
Factory injector
Direct-fit upgrades
Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.
| Injector | Flow | Fit |
|---|---|---|
| DeatschWerks DW 550cc matched set · 17U-08-0550-415 | 550 cc/min maker rating (basis not stated on page) | Needs adapter USCAR-to-OEM plug adapter (DW page states USCAR connector; adapter inclusion not stated) |
| DeatschWerks DW 1500cc matched set · 16M-03-1500-416 | 1500 cc/min maker rating (basis not stated on page) | Needs adapter USCAR-to-OEM plug adapter (DW page states USCAR connector; adapter inclusion not stated) |
| Fuel Injector Clinic FIC 445cc High-Z set · is116-0445h17 | 445 cc/min at 43.5 psi (3 bar), CF-16B fluid 90 F (maker) | Needs adapter USCAR-to-Honda OBD2 plug adapters PADPUtoH4 (optional) or solder-in pigtails PGTUSC4 (included) |
| Fuel Injector Clinic FIC 1000cc High-Z set · is116-1000h14 | 1000 cc/min at 43.5 psi (3 bar), CF-16B fluid 90 F (maker) | Needs adapter USCAR-to-Honda OBD2 plug adapters PADPUtoH4 (optional) or solder-in pigtails PGTUSC4 (included) |
| Injector Dynamics ID1050-XDS · 1050.48.14.14.446911 | 1065 cc/min at 3.0 bar, gasoline 52 C (maker) | Needs adapter USCAR-to-Honda OBD2/K-series plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238) |
| Injector Dynamics ID1300-XDS · 1300.48.14.14.4571012 | 1335 cc/min at 3.0 bar, iso-octane 52 C (maker) | Needs adapter USCAR-to-Honda OBD2/K-series plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238) |
K24A2 swap
Swap guides that recommend this engine or its family. Each guide covers mounts, transmission, fuel, wiring, tuning and the law, with sources.
Sensors
Factory sensors by role: part numbers, signal type and fitment years.
| Sensor | OEM part numbers | Type / signal | Years and markets |
|---|---|---|---|
| Knock | Honda 30530-PPL-A01 (replaces 30530-PNA-003)Sourced13 | knock sensor | US TSX 2004-08 (2006 page) |
| MAP | Honda 37830-PNC-003Sourced13 | MAP sensor | US 2006 TSX |
| MAF | Not yet sourcedSourced · medium13 | none listed in OEM catalogue (speed-density, MAP-based) | |
| O2 (upstream) | Honda 36531-RBB-003Sourced13 | wideband air-fuel ratio sensor (catalogue 'Sensor, LAF') | US 2006 TSX |
| O2 (downstream) | Honda 36532-RAD-L12Sourced · medium13 | oxygen sensor | US 2006 TSX |
Ignition and triggers
Tuning notes
Factory load sensing
The factory ECU measures load by MAP speed-density. 2004 TSX press: PGM-FI tracks intake-manifold pressure, ambient pressure and exhaust air/fuel ratio; Linear A/F sensor upstream of catalyst; CARB LEV-2. Downstream O2 assumed by OBD-II (not in press).Medium1
Factory oxygen sensors
Upstream: wideband A/F (Honda Linear Air/Fuel sensor) upstream of close-coupled cat (1). Downstream O2 sensors: yes. Closed-loop fuelling: LAF closed loop at part load; open loop enrichment at high load.Medium1
Driver and calibration
High-impedance injectors run from a saturated driver. Any injector change needs new flow and dead-time data in the calibration. Researched, unverified
Known limits (reported)
Stock rods and especially rod bolts are commonly reported as the first bottom-end limit under boost (vendor and forum consensus); some builders also add sleeves or a block guard because the block is open-deck (single forum opinion).Medium23
Common first upgrades (reported)
Builders most often report upgrading: forged rods with upgraded bolts (vendor/forum).Medium23
Valvetrain, factory engine management and weak points across every generation are on the Honda K-series guide.
Vehicles with the K24A2 (TSX)
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
17 sources
- Honda K24A2 sensing (E-826) · hondanews.com · oem · retrieved 2026-10-25
- Honda K-series internals (E-1035) · en.wikipedia.org · reference · retrieved 2026-10-25
- Honda K-series limits (E-1036) · hybrid-racing.com · vendor-doc · retrieved 2026-10-25
- Injector aftermarket fitment (E-1200) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector aftermarket fitment (E-1201) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / ID1050-XDS fitment (E-1230) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / ID1300-XDS fitment (E-1231) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / K-series stock flow (E-1240) · hybrid-racing.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1050-XDS fitment table (E-1260) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1300/ID1750/ID2600 fitment tables (E-1261) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1050-XDS fitment table (E-1290) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1300-XDS fitment table (E-1291) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- OEM sensor PNs (Acura RSX/TSX) (E-1353) · acurapartswarehouse.com · reference · retrieved 2026-10-25
- fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
- deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
- deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
- fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
Evidence ids (E-…) refer to our research register; each records the source, date and confidence.


