K Swap EG Civic (1992-95): K20 and K24 Swap Guide

A K-swap EG Civic is one of the most common Honda engine swaps, backed by bolt-in mounts, axles, shifters and hoses made for the 1992-95 chassis. It takes a K20 or K24 with its own manual gearbox, a matching mount kit and swap axles. The main hurdles are wiring and engine management, converting the fuel system, and routing the cooling hoses.Medium7456

Difficulty2/5 · EasyMedium7452
  • Bolt-in mount kits exist for the EG, but the factory transmission bracket must be cut off the frame rail.
  • Mounts, axles, shifter and cables must all match the same K-series gearbox family.
  • The donor fuel supply is returnless while the EG is return-style, so the fuel system needs converting.
  • Engine wiring and management are the largest single job and drive-by-wire engines add a pedal and throttle controller.

At a glance

The key numbers and parts, with the source on each tile.

Swap ecosystem

Bolt-in K-series mount kits are made for the 1992-95 Civic, 1994-01 Integra and Del Sol

Sourced7
Recommended engines
  • K20A2 or K20Z3 for revs
  • K24A2 or K24A1/A4 for torque
Wikipedia lists the K20A2 at 200 hp (149 kW) at 7,400 rpm and the K24A2 at 164-166 lb-ft (222-225 Nm) at 4,500 rpm.Sourced · medium3
K20A weight
  • About 275 lb without gearbox125 kg
  • 403 lb with it183 kg
Wikipedia figure, no OEM weight found. No sourced weight for the stock engine was found, so weigh yours if it matters.Sourced · medium3
Transmission
  • K-series manual gearbox
  • Mount variants for RSX/02-11 Si, 03-07 Accord/04-08 TSX, 12-15 Si and CR-V/Element
Sourced7
Factory LSD option

2006-11 Civic Si six-speed has a helical limited-slip differential

Sourced2
Axles

Swap-specific axles that use the donor engine's intermediate shaft

Sourced · medium4
ThrottleK20Z3 and K24A2 (TSX) are drive-by-wire2006 SiSourced21
Load sensing

Factory PGM-FI reads manifold pressure (speed density) plus crank and both cam positions

Sourced21
Fuel system
  • K-series donors are returnless
  • This chassis is return-style, so convert
Sourced · medium5

Recommended engines

  • K20A2 (RSX Type S / EP3 EU Type R) · RSX Type-S / EP3 Type R engine with 11.0:1 compression and VTEC on both cams; it pairs with the RSX-family gearbox that most swap mounts, axles and shifter parts were designed around.
  • K20Z1 / K20Z3 · The K20Z3 from the 2006-11 Civic Si is easy to find and comes with a six-speed that has a factory helical limited-slip differential; it is drive-by-wire, so plan the pedal and throttle control.
  • K24A2 (TSX) · The 2004-08 TSX engine has the long 99 mm stroke for more midrange torque at a similar peak power to the K20A2; it is drive-by-wire and needs the Accord/TSX-specific mount variant if you keep its gearbox.
  • K24A1 / K24A4 (CR-V / Accord) · CR-V and Accord K24 blocks are the cheapest way into K-series displacement; lower compression and economy-oriented VTEC make them a budget street or boost base rather than a high-rpm engine.

Mounts

Most EG K-swaps sit on a bolt-in kit built for the K-series.

Mount kit

Hasport EGK, sold per gearbox family with 62A, 70A, 88A or 94A urethane

Sourced7
Chassis modificationCut the stock transmission bracket off the frame railSourced7
Body styleWorks in manual and automatic EG chassisSourced7

Hasport's EGK kit covers the 1992-95 Civic, 1994-01 Integra and Del Sol, and it is sold in versions for each K-series gearbox family. The one permanent change is cutting the stock transmission bracket off the frame rail.7

Bushing hardness trades comfort for control. Hasport rates 62A urethane for street cars and 88A or 94A for race use, where the engine moves less but more vibration reaches the cabin. The hardness is part of the order, so choose it with the car's use in mind.7

Transmission

A K-swap uses a K-series transmission, and the mount kit has to match it.

GearboxUse the K-series manual that matches your mount kit variantSourced7
2006-11 Si six-speedHelical LSD, 4.765:1 final driveSourced2
Axles

Swap axles bolt to the donor intermediate shaft and are not OEM replacement axles for the donor car

Sourced · medium4

Hasport sells its kit in versions for RSX and 2002-11 Civic Si gearboxes, 2003-07 Accord and 2004-08 TSX gearboxes, 2012-15 Civic Si gearboxes, and CR-V or Element gearboxes. Pick the gearbox first, then order mounts, shifter and cables for that family.7

The 2006-11 Civic Si six-speed is a common choice. Honda fitted it with a helical limited-slip differential and a 4.765:1 final drive, which suits a light chassis on street tires. Earlier RSX and EP3 boxes are open-differential unless upgraded.Medium23

Axles are swap-specific. Kits made for the EG, EK and DC Integra bolt to the donor engine's intermediate shaft and the chassis hubs. One maker rates its stock-style swap axles for street and light track use, so budget stronger axles for big power or drag launches.Medium4

Clearance

Engine bay

Hasport notes engine bay modifications beyond the bracket cut may be needed

Sourced · medium7
Radiator

Full-width RSX/EP3 radiator needs its mounting tabs moved in a Civic

Sourced · medium6

The EG bay accepts a K-series with a swap kit, but check three areas: the radiator and hose path at the front, the intake path on the driver side, and the header and downpipe near the firewall and floor. Hasport's EGK page says some engine bay modification is needed, so test-fit before final paint.Medium76

Ground clearance under the oil pan and downpipe matters on a lowered EG. Measure the lowest points with the car at ride height and loaded, and confirm the hood closes with the intake and throttle body fitted.Low7

Cooling

Factory hoses do not connect a K-series to this chassis's radiator.

Upper hose
  • K20-style heads have the coolant outlet on the front
  • K24-style heads have it on the side
Sourced · medium6
Thermostat housing

Swap hose kits expect a downward-pointing housing, as on most K20s

Sourced · medium6
RSX/EP3 radiator
  • Full-width unit
  • Civic installs need the radiator tabs moved
Sourced · medium6

Swap hose kits are sold by head type, because K20-style heads put the upper coolant outlet on the front and K24-style heads put it on the side. Both common kits assume a thermostat housing that points down.Medium6

Many builders fit a full-width RSX or EP3 radiator for capacity. In a Civic that means moving the radiator mounting tabs. Decide radiator location before buying hoses, because hose shapes differ for half-width and full-width layouts.Medium6

Fans need a switching source. Either fit a fan switch in a hose or radiator bung, or let the engine computer drive a relay from coolant temperature. Bleed air from the system at the highest point and never open a hot, pressurized system.Low6

Fuel

K-series engines usually arrive without a return line because the donor car regulates pressure in the tank.

Donor layoutReturnless: regulator in the tank, single line to the railSourced · medium5
Chassis layoutEG, EK and DC2 use a return-style systemSourced · medium5
Typical kit

Center-feed rail, regulator with gauge, inline filter and pre-made lines

Sourced · medium5

The EG, EK and DC2 run a return-style system, so the swap needs an engine-bay regulator and a return path. Swap kits package a center-feed rail, regulator, filter and lines for this.Medium5

Mount the regulator where the kit maker specifies; one common kit puts it on the driver-side shock tower ahead of the brake master cylinder. Set and confirm base pressure with a gauge before first start, and record it so the fuel calibration starts from a known value.Medium5

Exhaust

Honda mounted the K-series exhaust manifold at the rear of the engine on the Civic Si and TSX, close to the catalyst.

Manifold positionRear of the engine, toward the firewall, on the Si and TSXSourced21
Upstream sensorTSX uses a linear air/fuel sensor ahead of the catalystSourced1

In the EG, the header still exits toward the firewall, so a swap header and downpipe shaped for the chassis are needed rather than the donor's manifold and pipe.Medium21

Plan sensor bungs at the same time. The TSX runs a linear air/fuel sensor ahead of its catalyst. For calibration, add a bung for a wideband oxygen sensor far enough downstream for the gas to mix, and keep catalyst and downstream sensor locations if the car must pass an emissions inspection.Medium1

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads
Engine sensors

Throttle position, coolant and intake temperature, manifold and barometric pressure, exhaust air/fuel, crank and both cams

Sourced12
Throttle control
  • Drive-by-wire on K20Z3 and K24A2
  • Needs an electronic pedal and throttle control
Sourced21

The engine needs power, ground and signals for its crank and two cam position sensors, injectors, ignition coils, VTEC solenoid and VTC oil control valve, plus throttle position, manifold pressure, temperatures and the exhaust air/fuel sensor. Whatever controls the engine must support all of these, and the engine harness must be adapted to this chassis.12

Decide throttle control early. The K20Z3 and K24A2 are drive-by-wire, so they need an electronic pedal and a controller that runs the throttle motor safely, or a cable-throttle intake from another K-series. Also plan fuel pump relay control, any immobilizer or security link the donor computer expects, and A/C and fan requests.Medium21

The K-series computer reads its own coolant sensor, so the EG cluster still needs its own inputs: a tachometer signal, a coolant sender it understands, the oil pressure switch, the check-engine lamp and vehicle speed. Fuse every new circuit at the source, size wire for its load, and use relays for the fuel pump, fans and main power.Low1

Chassis

A K-series in the EG Civic adds power and torque well beyond the original engine, so check the rest of the car.

Axle ratingStock-style swap axles are aimed at street and light track useSourced · medium4
Engine output

K-series engines in this guide are rated 160-205 hp (119-153 kW) by trim and year

Sourced · medium3

Inspect front hubs, wheel bearings and ball joints, and fit brake pads, fluid and lines suited to repeated hard stops before the first drive.Low3

Axles take the launch load. Stock-style swap axles are sold for street and light track use; drag launches, sticky tires and boosted engines call for stronger axles. Check axle plunge at full droop and full bump after the engine sits on its final mounts.Medium4

Tuning

Factory load strategySpeed density from manifold pressureSourced12
Cam controlVTEC lift change plus VTC intake cam phasingSourced · medium3

Honda's K-series computers calculate load from manifold pressure, a speed-density strategy, and trim fuel with an exhaust air/fuel sensor. A swap calibration usually keeps that approach. Start from injector data and engine displacement, then correct the volumetric efficiency table from wideband logs across the load and rpm range.Medium12

VTEC switchover and VTC cam phasing are calibration choices, not fixed numbers. Pick the VTEC crossover where the two cam profiles make equal torque, and pick cam angles cell by cell from logs. Advance ignition only as far as knock monitoring and logged results support; no fixed timing figure is safe for every engine and fuel.Medium3

Log everything on the first drives

Lambda, manifold pressure, coolant and intake temperature, knock activity and cam angle versus target. A K24 block with a K20 head or other mixed builds changes airflow, so a donor map is only a starting point.Low3

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 25 ticked (saved in this browser)
Mounts
Transmission
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

11 stages, in the order most builds follow.

  1. Plan the combination
    Choose engine, gearbox and engine management together, then order the matching mount kit variant, axles, shifter, cables, hoses and fuel parts for that gearbox family.
  2. Prepare the donor
    Check compression and leak-down, replace the timing chain tensioner if worn, and fit fresh seals, clutch and flywheel while the engine is out.
  3. Strip the chassis
    Remove the old engine, gearbox, axles, shifter, harness sections that will not be reused, and fuel lines in the engine bay. Label everything.
  4. Modify and fit mounts
    Cut brackets the mount kit calls for, clean and paint bare metal, and test-fit the mounts on the bare chassis.
  5. Install the engine and gearbox
    Lower the assembly on a hoist with a load leveler, set it on the mounts, and torque hardware to the kit maker's figures.
  6. Fit driveline and shifter
    Install axles with the donor intermediate shaft, the shifter, cables and clutch hydraulics; bleed the clutch.
  7. Plumb fuel and cooling
    Install the fuel rail, regulator and return, radiator and swap hoses. Pressure-test fuel and cooling before first start.
  8. Wire the engine
    Adapt power, grounds, sensors, throttle control, pump relay, fans, gauges and A/C. Fuse every new circuit.
  9. First start and checks
    Prime oil pressure, confirm fuel pressure and cam/crank sync, start, and check for leaks while monitoring coolant temperature.
  10. Calibrate and log
    Fit a wideband, build fuel and cam tables from logs, and add load gradually while watching knock and temperatures.
  11. Inspect and register
    Re-torque mounts and axles after the first drives, then complete emissions, registration and insurance steps for your region.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Axles bind, click or do not reach the hubAxles do not match the mount layout or the intermediate shaftBuy axles specified for your chassis, mount brand and the donor intermediate shaft; check plunge at full droop and bump.Medium4
Engine overheats or will not bleedHoses do not suit the head's coolant outlet position or the thermostat housing points the wrong wayUse a hose kit for your head type with a downward thermostat housing, and bleed from the highest point.Medium6
Lean running and pressure drop under loadDonor returnless supply fed into a return-style chassis without a proper regulatorConvert to an engine-bay regulator with return, and confirm pressure with a gauge at idle and under load.Medium5
Engine starts but will not rev, or throttle stays shutDrive-by-wire engine fitted without an electronic pedal and throttle controlFit an electronic pedal and a controller that runs the throttle motor, or use a cable-throttle intake.Medium21
Gearbox mounts or shifter do not line upMount kit variant ordered for a different gearbox familyMatch the kit variant to the transmission (RSX/Si, Accord/TSX, 2012-15 Si or CR-V/Element).7
Fails a California Referee inspectionEmissions equipment from the donor configuration is missing or disconnectedInstall and connect the donor's emissions controls and book a Referee inspection; the test follows the donor vehicle's smog requirements.9

Frequently asked

What do I need to K-swap an EG Civic?

You need a K-series engine with its harness section, a matching K-series manual gearbox, a K-swap mount kit for that gearbox, swap axles, shifter and cables, a radiator and swap hoses, a fuel return conversion, a swap header, and engine management that runs VTEC and cam phasing. Plan the wiring and the chassis gauge signals before buying parts.Medium7456

Does a K24 fit in an EG Civic?

Yes. Swap mount kits for the EG accept K20 and K24 engines, and swap hose kits are sold for K24-style heads with the side coolant outlet. If you keep the Accord or TSX gearbox behind a K24, order the mount variant made for that gearbox family.Medium76

Which transmission is best for an EG K-swap?

The 2006-11 Civic Si six-speed is popular because Honda gave it a helical limited-slip differential and a 4.765:1 final drive. RSX and EP3 gearboxes are also widely used and are the basis for most cable and axle parts. Whatever you choose, the mount kit, cables and shifter must match it.Medium27

Do you have to cut the EG frame for a K-swap?

Yes, a small cut. Hasport's EGK kit requires cutting the stock transmission bracket off the frame rail. The rest of the kit bolts to factory mounting points, though Hasport notes some engine bay modification may be needed depending on the parts fitted.7

What axles does an EG K-swap need?

It needs swap-specific axles that join the K-series intermediate shaft and gearbox to the EG hubs. Stock-style swap axles are sold for street and light track use and are not replacement axles for the donor RSX or Civic Si. Choose stronger axles for high power or hard launches.Medium4

Is a K-swapped EG Civic street legal?

It can be, depending on where you live. In California an engine change needs a BAR Referee inspection against the donor vehicle's smog rules. The UK requires a V5C update with evidence, Germany requires an inspector's approval, and Australian states apply VSB 14. This is general information, not legal advice.Medium9101112

Related

Sources

12 sources
  1. 2004 Acura TSX Powertrain (press release, part 2) · American Honda Motor Co. (Acura) · oem · retrieved 2026-10-25
  2. 2006 Honda Civic Powertrains (press release) · American Honda Motor Co. · oem · retrieved 2026-10-25
  3. Honda K engine · Wikipedia · reference · retrieved 2026-10-25
  4. K Swap Axles for EG/EK Civic and DC Integra (product page) · Hybrid Racing · vendor-doc · retrieved 2026-10-25
  5. K-Tuned K-Swap Center Feed Fuel System (EG, EK, DC2) - retailer listing · K-Tuned (listing by Speed Science) · vendor-doc · retrieved 2026-10-25
  6. K-Tuned K-Swap Radiator Hoses for RSX/EP3 radiator (EG, DC2, EK) - retailer listing · K-Tuned (listing by Tegiwa) · vendor-doc · retrieved 2026-10-25
  7. EGK K-series Mount Kit (92-95 Civic, 94-01 Integra, Del Sol) · Hasport Performance · vendor-doc · retrieved 2026-10-25
  8. Tampering Policy: The EPA Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  9. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  10. Change vehicle details on a V5C: what evidence to give · GOV.UK (DVLA) · standard · retrieved 2026-10-25
  11. Strassenverkehrs-Zulassungs-Ordnung (StVZO) section 19: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  12. Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government, Department of Infrastructure · standard · retrieved 2026-10-25