Data logging

dataloggingdata acquisitionDAQloggingdatalog

Data logging is recording engine and vehicle signals over time, such as speed, load, air-fuel ratio, timing, boost and temperatures, for later review. In tuning, logs show what the engine actually did, so calibration changes are based on measured data rather than feel.12

How it works

A logger samples each channel at a set rate and stores a time stamp with each value.

Sources include the engine controller's own variables, separate sensors, and messages from other modules on the CAN bus.Medium13

Through the OBD-II port, a logger can request standard parameters defined in SAE J1979 and its digital annex, such as engine speed, coolant temperature and calculated load. These are emissions diagnostic data and are often limited in rate and resolution.45

Sample rate must suit the signal. Temperatures change slowly and need only a few samples per second. Knock, lambda during transients, boost and wheel speed change quickly and need far higher rates.Medium12

In tuning

A useful tuning log includes engine speed, load or manifold pressure, throttle, target and measured lambda, ignition timing, knock activity, fuel and ignition corrections, intake and coolant temperature, boost target and actual, and battery voltage.Medium2

Review logs against targets, not just raw values. Look for where corrections are large, where targets are missed and where knock or limits act. Steady repeatable conditions make comparisons meaningful.Medium21

Label data honestly. Note fuel, weather, altitude and hardware for each session so later comparisons are fair. Logs from different conditions should not be mixed without correction.Low1

Formula and worked example

Try it

psi
°F
%
hp

Result

SAE J1349 factor1.017 :1
STD (SAE J607) factor1.055 :1

Planning estimate from the formula below, not a measurement.

Open the full dyno correction factor calculator (sae j1349 and std) →

Myths vs facts

Myth A higher logging rate is always better.

Fact Very high rates on slow signals waste storage and can reduce rates on important channels. Match rate to signal speed.Medium1

Myth OBD logging shows everything the controller sees.

Fact Standard OBD parameters are a limited emissions subset. Internal calibration variables need manufacturer or controller-specific access.45

Frequently asked

What parameters should I log when tuning?

At minimum log engine speed, load or manifold pressure, throttle position, target and actual lambda or air-fuel ratio, ignition timing, knock activity, fuel corrections, intake and coolant temperatures and battery voltage. Turbocharged engines add boost target and actual and wastegate duty. Add fuel pressure if a sensor is fitted.Medium2

What sample rate do I need?

Match rate to how fast each signal changes. Temperatures are fine at 1 to 10 Hz. Engine speed, throttle, boost and lambda usually need 20 to 100 Hz to show transients. At 6,000 rpm a crank revolution takes 10 ms, so even 100 Hz captures only one sample per revolution.Medium12

Can I log through the OBD port?

Yes, for standard parameters. SAE J1979 defines diagnostic services and parameter identifiers that any compliant scan tool can request, such as speed, coolant temperature and calculated load. Rates are limited by the request-response method and network traffic, and many internal calibration values are not available that way.45

How do you read a datalog?

Start with a steady, repeatable section such as a full-throttle pull in one gear. Check that targets were met: lambda, boost and cam angle. Then look for knock activity, large fuel corrections, temperature trends and limits that intervened. Compare against a previous log under similar conditions before changing anything.Medium21

Wiring, pinouts and parts

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Data logger · Wikipedia · reference · retrieved 2026-10-25
  2. Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-25
  3. CAN bus · Wikipedia · reference · retrieved 2026-10-25
  4. SAE J1979 E/E Diagnostic Test Modes (2014) · SAE International · standard · retrieved 2026-10-25
  5. On-board diagnostics · Wikipedia · reference · retrieved 2026-10-25