At a glance
The key numbers and parts, with the source on each tile.
5.7 Hemi from a 2006-08 Commander or Grand Cherokee (2007-10 JK kit)
Ram and Durango 5.7s have a different accessory drive and intake location.Sourced · medium4Stellantis rates the 2022 Ram 1500 5.7 at 395 hp at 5,600 rpm and 410 lb-ft (556 Nm) at 3,950 rpm
Older Jeep 5.7s are rated lower.Sourced1Kit mounts that index off existing frame holes, plus a new transmission crossmember
Sourced · medium4Recommended engines
- 5.7 Hemi (Eagle, VVT 2009+) · The most common JK conversion engine. Grand Cherokee and Commander donors share Jeep-style accessory drives, and conversion kits were built around them.
- 6.1 / 6.4 392 Hemi · More displacement and torque, and the engine Jeep later fitted to the JL Wrangler 392. Costs more and needs a transmission and axles rated for it.
Mounts
A JK Hemi swap is usually built around a conversion kit's mounts, which locate off holes already in the frame.
Transmission mount, crossmember, battery tray and steering relocation bracket
Sourced · medium4That keeps engine position repeatable and leaves room for the steering shaft, which the kit relocates with its own bracket.Medium4
Kits were specific to model years and donor engines. The 2007-10 kit called for 2006-08 Jeep 5.7 engines; later kits covered 2012-14 JKs with 5.7 or 6.4 engines. Check fitment before buying used kit parts.Medium45
Transmission
The documented Australian conversion paired the 5.7 with a new 545RFE five-speed automatic.
The kit supplied a transmission crossmember and a heavy-duty transmission cooler with lines.Medium64
The factory JK transmissions were built for V6 torque. A Hemi needs a transmission from the Hemi family, matched to your transfer case input and with its controls handled by the donor computer or a separate controller.Low36
Recheck front and rear driveshaft lengths and angles after the swap. The engine and transmission set the transfer case position, and lifted JKs are sensitive to driveshaft angle.Low4
Clearance
The Hemi is a large pushrod V8 in a bay laid out for a V6, so expect to relocate the battery, re-route the steering shaft and modify brackets. The kits handled this with a new battery tray, steering bracket and bent A/C and power steering lines.Medium4
Do not mix donor families without checking. The 2007-10 kit was designed for Jeep-style accessory drives and intake positions; Ram and Durango 5.7s place them differently and will not fit the kit's parts.Medium4
Cooling
The Hemi rejects much more heat than the V6, and the JK grille opening stays the same size.
Use a radiator built for the conversion and a transmission cooler sized for the automatic.Medium46
Slow rock crawling and towing are the hardest cases for cooling. Watch coolant and transmission temperature during the first long climbs and add hood venting if temperatures creep.Low6
Fuel
The JK keeps its tank and in-tank pump in a kit conversion, with a new line to the Hemi's rail.
Before the first start, confirm the pump can supply the V8 at the pressure the donor computer expects, then check every joint for leaks.Low4
Exhaust
Keep catalytic converters and oxygen sensors from the donor design, because the donor computer monitors them.
The documented Australian build used cast exhaust manifolds into a dual-to-single system and only just passed the local noise test.Medium6
Route pipes above the frame line where possible to protect them off-road, and keep them clear of the fuel tank and brake lines.Low4
Electrical
Any Hemi controller needs crank and cam position, sixteen spark plugs fired by eight coil-on-plug coils, eight injectors, drive-by-wire throttle and pedal, load and air temperature sensing, knock sensing and oxygen sensors. VVT engines need cam phaser control, and MDS engines need lifter solenoid control or a disabled MDS.Medium21
The JK runs nearly everything through networked modules. The cluster, stability control and body systems expect engine data on the CAN bus, so a factory-style Chrysler computer configured for the JK is the usual path. Fuel pump control, fans, A/C and gauges follow from that.Medium34
Immobilizer data lives in both the engine computer and the security module. Owners report start-then-stall faults when only one is reprogrammed. Safety: disconnect the battery before harness work and fuse every new feed.Low7
Chassis
The Hemi adds front weight, which is why the kit included spring spacers.
Recheck ride height, steering geometry and headlight aim after the swap.Medium4
V8 torque on big tires stresses axles, ball joints and steering. Many conversions add stronger axles; the documented Australian build planned heavy-duty front and rear axles, which would need its suspension tests repeated.Medium6
Tuning
Kit conversions used a custom-flashed Chrysler computer, which keeps factory diagnostics and lets dealers service the engine.
Tire size and axle ratio must be entered so the speedometer and shift schedule are correct.Medium46
If MDS stays active, keep the factory oil viscosity and the lifter solenoids healthy. If you disable it, do so in the calibration and confirm it with logging. Log wideband lambda and knock under towing loads, and keep spark changes conservative.Low2
Legal
Matches a certified configuration of the same or newer model year as the chassis
Sourced8Federally, the EPA's 2020 tampering policy accepts an engine switch that matches a certified configuration of the same or newer model year as the chassis. Watch donor age: a 2006-08 engine in a later JK may not meet that test. OBD tampering is excluded.8
California treats a Hemi swap as an engine change needing a BAR Referee inspection under the donor's requirements. We found no confirmation of a California exemption for the JK kits, so check before buying.Medium9
UK owners must update the V5C and should tell their insurer. In Germany, a swap needs individual approval under §19
Parts checklist
Tick what you have; the list is saved in this browser.
Order of work
10 stages, in the order most builds follow.
- Match donor to kitConfirm the donor engine family, model year and accessory layout fit your kit and your JK's model year.
- Remove the V6 drivetrainPull the engine and transmission, and remove the radiator, battery tray and intake. Label body connectors.
- Prepare the chassisFit mounts, the crossmember and the steering bracket, and complete any cutting and welding with lines shielded.
- Install engine and transmissionLower the Hemi and automatic with a load leveler, then fit the transfer case and check clearances.
- Cooling, fuel and exhaustInstall the radiator, transmission cooler, fuel line and exhaust with converters and sensors.
- AccessoriesFit the battery tray, A/C and power steering lines, and the air intake with its shield.
- Wiring and computer setupConnect the engine harness to the JK body harness, then set VIN, immobilizer, throttle, tire size and gear ratio.
- First start and checksCheck for leaks and codes, start, bleed the cooling system and confirm cluster, stability control and A/C work.
- Chassis and road testSet ride height, align, aim headlights, then road test with logging under load.
- InspectionComplete the emissions or engineering inspection your region requires.
Common problems
Symptom, cause and the usual fix.
| Problem | Cause | Fix |
|---|---|---|
| Engine starts then stalls after two seconds | Immobilizer data in the engine computer and security module do not match | Program the engine computer with the JK's VIN, then the security module and keys in the order the service information gives.Low7 |
| Kit parts do not line up with the donor engine | Ram or Durango 5.7 with a different accessory drive and intake location | Use a donor the kit was designed for, such as a 2006-08 Commander or Grand Cherokee for the 2007-10 kit.Medium4 |
| Cruise control or stability control lost after the swap | Network messages or a damaged clock spring after steering work | Scan all modules for communication codes and inspect the clock spring.Low3 |
| Speedometer and shifts are off | Tire size and axle ratio not set in the computer | Enter the correct tire size and gear ratio with the setup tool.Medium6 |
| Overheating on slow climbs or when towing | Not enough radiator capacity or hot underhood air | Use a conversion radiator and transmission cooler, and add hood venting.Medium64 |
Frequently asked
Which Hemi is best for a JK swap?
The 5.7 is the most common choice because kits were built around Jeep donors and parts are easy to find. The 6.4 adds displacement and is the engine Jeep later fitted to the JL Wrangler 392, but it costs more and loads the driveline harder. Match the donor's accessory layout to your kit.Medium452
How long does a JK Hemi swap take?
The best-known kit listed about 36-40 hours for an experienced installer, with cutting and welding required, and rated the job experts-only. An Australian installer quoted under a week in the shop. A first-time home build, with research and parts hunting, usually takes far longer than either figure.Medium46
What transmission do you use in a JK Hemi swap?
A Hemi-family automatic. The documented Australian conversion used a new 545RFE five-speed behind a 5.7. The JK's factory 42RLE, W5A580 and NSG370 were built behind V6 engines. Whatever you pick must suit the transfer case and be controlled by the engine computer or its own controller.Medium63
Will the JK's dash and stability control work with a Hemi?
They can, if the engine computer is set up for the JK. The JK runs almost every function through networked modules, so the cluster and stability control expect engine data. Kit conversions used a Chrysler computer flashed for the JK plus a setup module for VIN, throttle, tire size and gear ratio.Medium346
Is a JK Hemi swap street legal?
It can be, with work. The EPA accepts a switch that matches a certified configuration of the same or newer model year as the chassis, so donor age matters. California requires a BAR Referee inspection. Australian conversions are engineered to VSB 14. This is general information, not legal advice; check locally first.8912
Can I still buy a JK Hemi conversion kit?
Retail listings for the best-known 5.7 and 6.4 JK kits now say they are no longer available. Builders use used kit parts or source mounts, harness work and computer setup separately. Check that any used parts match your JK's model year and your donor engine before buying.Medium4
Related
Sources
12 sources
- 2022 Ram 1500 specifications (5.7L HEMI VVT V-8) · Stellantis North America Media · oem · retrieved 2026-10-25
- Chrysler Hemi engine · Wikipedia · reference · retrieved 2026-10-25
- Jeep Wrangler (JK) · Wikipedia · reference · retrieved 2026-10-25
- AEV 40307011AB 5.7L V8 Hemi Conversion Kit for 07-10 Jeep Wrangler JK · Quadratec · vendor-doc · retrieved 2026-10-25
- New From AEV: 2012+ JK Wrangler HEMI V8 Builder Kits · Off Road Xtreme · press · retrieved 2026-10-25
- AEV Hemi-powered JK Wrangler conversion · 4X4 Australia · press · retrieved 2026-10-25
- Hemi swap security · Diagnostic Network (diag.net) · community · retrieved 2026-10-25
- Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act · U.S. Environmental Protection Agency · standard · retrieved 2026-10-25
- Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
- Change vehicle details on a V5C registration certificate (log book) · GOV.UK (DVLA) · standard · retrieved 2026-10-25
- § 19 StVZO: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
- Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government Department of Infrastructure, Transport, Regional Development, Communications and the Arts · standard · retrieved 2026-10-25

