How it works
Every node connects to two twisted wires, CAN high and CAN low.
Data is sent as the voltage difference between them, which rejects noise. Texas Instruments describes classic CAN as a multi-master broadcast system with a maximum signaling rate of 1 Mbit/s.23
Messages carry an identifier, not a destination address. Classic CAN uses 11-bit standard or 29-bit extended identifiers, as defined in Bosch's CAN 2.0 specification. Every node receives every message and decides whether it cares.42
When two nodes transmit at once, they arbitrate bit by bit. A dominant bit overrides a recessive one, so the message with the lower identifier wins without corrupting the frame, and the loser retries. Lower identifiers therefore carry higher priority.23
ISO 11898-1:2024 now covers classic CAN, CAN FD and CAN XL. CAN FD speeds up the data phase and allows up to 64 data bytes; the ISO abstract states CAN XL supports data fields of up to 2,048 bytes.13
In tuning
Tuning uses CAN to read and send data: wideband controllers, dashes, loggers, power distribution modules and transmission controllers. Both ends must agree on bit rate, identifier format and how each signal is packed, including byte order, scaling and offset.Medium23
A high-speed CAN network needs a 120 ohm termination resistor at each physical end. With power off, about 60 ohms between CAN high and CAN low confirms two terminators. Long stubs, missing termination or untwisted wires cause errors.23
On a road car, adding nodes to the factory network can upset other modules, and sending messages that impersonate factory modules can disable safety functions. Use a separate bus or a gateway where possible.Low31
Formula and worked example
bus load = (Σ frames per second × bits per frame) / bit rate
- frames per second
- messages sent per second for each identifier1/s
- bits per frame
- frame length including overhead and interframe spacebit
- bit rate
- bus speedbit/s
Myths vs facts
Myth CAN has a master that polls each module.
Fact CAN is multi-master. Any node can transmit when the bus is idle, and arbitration by identifier resolves collisions.2
Frequently asked
How does CAN bus work?
Each module transmits short frames onto a shared pair of twisted wires. Each frame starts with an identifier that labels its content and sets priority. If two modules start together, the lower identifier wins arbitration without data loss. All modules receive every frame and use the ones they need, with CRC checks and acknowledgements catching errors.24
Why does CAN bus need 120 ohm resistors?
The resistors terminate the line at each end so signals do not reflect back along the cable and corrupt bits. They also set the bus impedance the transceivers expect. Two 120 ohm resistors in parallel measure about 60 ohms across CAN high and CAN low with power off, which is a quick wiring check.23
What is the difference between CAN and CAN FD?
Classic CAN carries up to 8 data bytes per frame at up to 1 Mbit/s. CAN FD, for flexible data rate, carries up to 64 bytes and can switch to a higher bit rate during the data phase. Both are now covered by ISO 11898-1, which also adds CAN XL with even larger data fields.132
What speed is CAN bus?
Classic high-speed CAN runs at up to 1 Mbit/s. Vehicle networks commonly use 500 kbit/s or 250 kbit/s, and heavy-duty J1939 networks traditionally run at 250 kbit/s. Maximum reliable speed falls as cable length grows, because every node must see each bit within one bit time.Medium273
How many devices can be on a CAN bus?
The protocol has no fixed node limit, but the electrical layer does. Transceiver load, cable length and bus traffic limit practical size. Many automotive networks run a few dozen nodes per bus and split into several buses joined by gateways. Check the transceiver data sheet for its rated load.Medium23
Used in these guides
- 2.5 TFSI + DQ500 DSG swap guide: VW Golf Mk7 and Golf R
- 2JZ + BMW M DCT swap guide: Nissan 240SX (S13)
- 2JZ Swap BMW E46 3 Series (1999-2006): 2JZ-GTE and 2JZ-GE Guide
- 1.8T + DQ250 DSG swap guide: VW Golf Mk4 (1.8T and VR6)
- Hemi Swap Jeep JK (2007-18): 5.7 and 6.4 Conversion Guide
- Hemi Swap Jeep Wrangler TJ (1997-2006): Mounts, Transmission, Transfer Case and Legal Guide
- Honda Fit K-Swap (GD, GE, GK 2007-2020): Mounts, Axles, Shifter Cables, CAN Wiring and Legal Guide
- Mini Cooper K-Swap (R50/R53 2002-06, R56 2007-13): Mounts, Oil Pan, Axles, Wiring and Legal Guide
- Subaru BRZ / Scion FR-S / Toyota 86 K Swap (2013-2020): K24 Mounts, Stock Gearbox, CAN Bus, Wiring and Legal Guide
- Toyota MR2 K Swap (Spyder 2000-07 and SW20 1991-99): Mounts, Transaxle, Axles, Shift Cables, Wiring and Legal Guide
- K24 + BMW M DCT swap guide: Honda S2000 (AP1 / AP2)
- LS + BMW M DCT swap guide: BMW E36
- LS Swap BMW E46: Mounts, CAN Bus Cluster, Subframe and Legal Guide
- Ford Ranger LS Swap (1983-2011): Mounts, Oil Pan, Transmission, PATS, Speedometer, Fuel and Legal Guide
- G35 LS Swap (V35, 2003-2007): Sedan and Coupe Kits, CD009 or T56, Driveshaft, CAN Gauges, Automatics and Legal Guide
- Jeep Wrangler LS Swap (TJ 1997-2006 and JK 2007-2018): Mounts, Transfer Case Adapters, Fuel, CAN Bus Integration and Legal Guide
- RX-8 LS Swap (SE3P, 2004-2011 US): Mounts, PPF Delete, Steering Rack, Differential, CAN Gauges and Legal Guide
- 350Z LS Swap (Z33): Engines, Mounts, CD009 or T56, Wiring, Gauges and Legal Guide
- Subaru BRZ / Scion FR-S / Toyota 86 LS Swap (2013-2020): Mounts, Gearbox, CAN Bus, Wiring and Legal Guide
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- ISO 11898-1:2024 Road vehicles, Controller area network (CAN), Part 1: Data link layer and physical coding sublayer · International Organization for Standardization · standard · retrieved 2026-10-25
- Introduction to the Controller Area Network (CAN), application report SLOA101B · Texas Instruments · vendor-doc · retrieved 2026-10-25
- CAN bus · Wikipedia · reference · retrieved 2026-10-25
- CAN Specification 2.0: Protocol and Implementations (SAE 921603) · SAE International · sae-paper · retrieved 2026-10-25
- SAE J1979 E/E Diagnostic Test Modes (2014) · SAE International · standard · retrieved 2026-10-25
- On-board diagnostics · Wikipedia · reference · retrieved 2026-10-25
- SAE J1939 · Wikipedia · reference · retrieved 2026-10-25

