Subaru BRZ / Scion FR-S / Toyota 86 LS Swap (2013-2020): Mounts, Gearbox, CAN Bus, Wiring and Legal Guide

An LS swap BRZ, FR-S or 86 is an established but advanced build with bolt-in mount, oil pan, header and driveshaft kits from Sikky and an ICT Billet mount kit. It needs a GM-pattern manual such as a T56, TR6060 or CD009. The hard parts are keeping the CAN-bus chassis working (cluster, ABS/VSC, steering), the driveline and rear axles, and emissions legality.Medium3912101

Difficulty4/5 · HardMedium351210120
  • Mounts, pan, headers and driveshaft bolt in from kits, but the gearbox is new to the car and needs its own mount, clutch master cylinder and driveshaft.
  • The 86 is a CAN-bus car: the cluster, ABS/VSC and electric steering expect messages from the factory engine computer, so the swap needs an 86-specific harness or CAN module.
  • Subaru rated the FA20 at 151 lb-ft (205 Nm); an LS roughly doubles to triples that, so the Torsen differential, rear axles and diff bushings become the weak links.
  • A 2013-2020 car is OBD-II era and the LS harnesses are sold for off-road use, so a road-legal result depends on local emissions rules.

At a glance

The key numbers and parts, with the source on each tile.

Stock engine
  • 2.0 L FA20 flat-four
  • Subaru rated it at 200 hp at 7,000 rpm and 151 lb-ft at 6,400 rpm2013 BRZ
Sourced1
Curb weight

2,762-2,822 lb (1,253-1,280 kg) for the 2013 BRZ, depending on trim and gearbox

Sourced1
Mount kits
  • Sikky Stage 1 / Stage 2 packages or a la carte kit
  • ICT Billet 6061-T6 mount kit
Sourced · medium359
Transmission

Sikky lists T56, T56 Magnum, TR6060 and CD009 options with matching driveshafts

Sourced · medium3
Oil pan

Front-sump LS pan: Sikky's own pan, or a Moroso front-sump pan with ICT mounts

Sourced · medium39
CAN bus
  • Cluster, ABS/VSC and steering need engine data
  • Use an 86-specific CAN harness or module
Sourced · medium121016
Differential
  • Torsen limited-slip, 4.100 final drive in the 2013 BRZ
  • 4.30 on the 2017+ manual 86
Sourced12
Fuel
  • 13.2 gal tank50 L
  • GM specifies about 58-60 psi and 45 gph for the LS3
Sourced122
Legal route
  • Off-road harnesses
  • Road use depends on EPA/CARB, DVLA, TUV or state engineering rules
Sourced · medium122324

Recommended engines

  • LS3 / L99 · The best-documented route in this chassis: Wiring Specialties builds an 86-specific LS3 drive-by-wire harness and a CAN module for the E38 computer, and the published LS3 BRZ builds pair it with a T56.
  • LS1 · Sikky's turnkey 86 build starts from a used LS1 with a T56, and Wiring Specialties offers an LS1 86 harness. It needs the cable-throttle conversion, because the LS1 is drive-by-cable and the 86 pedal is electronic.
  • 5.3 LM7 / L59 / LY5 (Gen III/IV truck) · The low-cost iron-block truck engine. Wiring Specialties lists 1999-2004 truck LSx engines for its 86 LS1 harness, but the truck accessories, pan and intake must change to fit a low sports-car bay.
  • LS2 · The first LS shown in a BRZ was a GTO LS2 mock-up in 2012. It is a 58x drive-by-wire engine like the LS3, so the same wiring logic applies; confirm harness support with your harness maker first.

Mounts

For an LS swap BRZ, Sikky is the main kit maker.

Sikky Stage 1 (MK012-FRS)
  • Engine mounts, transmission mount, front-sump pan, remote oil filter kit, Grade 8 hardware
  • LHD or RHD
Sourced · medium3
Sikky Stage 2 (MK012-2-FRS)Stage 1 plus 1-7/8 in stainless headers with 3 in collectorsSourced · medium48
ICT Billet kit
  • 6061-T6 frame mounts, engine mounts, polyurethane bushings and hardware
  • Positioned for a Moroso front-sump pan
Sourced · medium9

Its Stage 1 package bundles CNC-cut steel and billet engine mounts with urethane bushings, a transmission mount, a front-sump oil pan and a remote filter kit. Stage 2 adds stainless headers, and an a la carte kit lets you buy the same parts one at a time.Medium345

ICT Billet sells a separate 6061-T6 billet mount kit for the 2013-2016 FR-S, 2013-2020 BRZ and 2012-2021 GT86. It includes frame mounts, engine mounts, polyurethane bushings and hardware, and ICT sets the engine height around a Moroso front-sump pan, so buy the pan the mounts were designed for.Medium9

Vorshlag also announced 86 LS parts in 2016, including mounts, a crossmember and a driveshaft. LSX Magazine reported them as coming soon, and no current product page was found, so treat that route as unconfirmed.Low13

Transmission

The FA20's bellhousing does not match the LS, so the factory TL70 manual stays behind.

Supported gearboxes (Sikky)T56, T56 Magnum, T56 Magnum F, TR6060, CD009Sourced · medium35
Stock 86 gearboxes6-speed TL70 manual (Aisin AZ6 based) or 6-speed A960E automaticSourced · medium2
Clutch hydraulics

Sikky master cylinder kits for T56 (MCK111), TR6060 (MCK119) and CD00X (MCK120)

Sourced · medium5

Sikky's configurator lists the T56, T56 Magnum, TR6060 and Nissan CD009, each with its own transmission mount and driveshaft; its turnkey service also lists the 4L60E automatic. The T56 family has been GM's LS manual for decades, which keeps parts easy to find.Medium36221

Check the mount against the gearbox before ordering. Sikky's Stage 1 page lists its transmission mount for the T56, T56 Magnum and TR6060, while the CD009 appears as a separate gearbox and driveshaft choice with its own adapter kit, so confirm the CD009 mount part with Sikky.Medium35

Every option needs a new driveshaft. Sikky sells steel and aluminum shafts sized per gearbox, replacing the factory shaft, which KPower describes as a two-piece unit of about 29 lb (13 kg). A clutch master cylinder kit with lines matches the hydraulic release of the new gearbox.Medium3519

No maker publishes where each gearbox's shifter lands in the 86 console. Mock up the engine and gearbox before cutting anything and check the shifter against the stock opening.Low3

Clearance

Every 86 LS kit uses a front-sump pan.

Sikky pan

Front sump, 5.5 in (140 mm) deep, about 7.4 qt (7.0 L) excluding the filter

Sourced · medium3
Summit listing (OP009K)

Front sump, 5.125 in (130 mm) deep, 6.80 qt (6.4 L), baffled, pickup and dipstick included

Sources differ on depth and capacity; confirm with Sikky.Sourced · medium7
HoodA 2012 LS2 mock-up was reported to fit under the stock hoodLow confidence14

Sikky's pan has a billet flange, trap-door baffles and a side-port remote filter adapter. Its product page lists about 7.4 qt and 5.5 in deep, while Summit's OP009K listing says 6.80 qt and 5.125 in, so confirm before planning ground clearance.Medium37

The Sikky pan reuses some factory hardware that the kit omits, and Summit lists the oil pump, pump driveshaft and gaskets as not included. Order a gasket and any missing bolts with the pan to avoid a stalled install.Medium37

LSX Magazine reported in 2012 that a GTO LS2 mock-up in a BRZ cleared the stock hood, but that car was not running yet. No current maker states hood clearance for each intake, so check yours with the engine on its mounts.Low14

Cooling

No 86-specific LS radiator was found from the kit makers.

HosesSikky's turnkey build lists custom radiator hosesSourced · medium6
Fans
  • Wiring Specialties' harness supports dual fans through factory wiring
  • Its CAN module adds chassis fan control
Sourced · medium1210

Sikky's turnkey build lists custom radiator hoses with a radiator not specified, so plan for an aluminum radiator sized for a V8 and hoses that clear the new pan and headers.Low6

Wiring Specialties wires dual 30 A fans through the factory circuits and its CAN module drives chassis fan control from the GM computer. Plumb the LS steam port and heater lines the way GM's LS3 installation guide describes rather than capping them.Medium121022

Fuel

The FA20 uses Toyota's D-4S direct plus port injection, so its fuel supply is built for a high-pressure engine pump.

Stock tank13.2gal50 LSourced1
LS3 requirement

About 58-60 psi (400 kPa) and 45 gph (170 L/h) at that pressure, per GM

Sourced22
Kit options
  • Sikky turnkey: fuel line kit with pump upgrade
  • Harness options for OEM pump or aftermarket kit
Sourced · medium612

An LS runs port injection only, and GM specifies roughly 58-60 psi and 45 gph for the LS3 crate engine. Plan a pump and regulator setup that meets that target.Medium122

Sikky's turnkey build adds a fuel line kit and pump upgrade, and the Wiring Specialties harness can run the factory pump setup or an aftermarket pump kit through its fused relay box. Confirm how the factory fuel pump controller is handled with your harness maker.Medium612

Exhaust

Sikky headers (HDR021SS)

1-7/8 in stainless primaries, 3 in collectors with merge bullets, V-band flanges

Sourced · medium45
Brake lines

Sikky's HLK-07 kit moves the factory rear brake lines away from the headers

Sourced · medium5

Sikky's 86 headers use 1-7/8 in stainless primaries into 3 in collectors with V-band flanges, and Sikky says they suit most gearbox combinations. Its turnkey build makes a custom joint from the headers to the existing cat-back.Medium46

The headers run close to the factory rear brake lines. Sikky sells a brake line kit that reroutes them, which is cheaper than finding boiled or damaged lines after the first hard drive.Medium5

Wiring Specialties' LS3 harness carries both front O2 sensor connectors, so plan sensor bungs in each collector and catalysts where your emissions rules require them.Medium12

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads

The 86 is a CAN-bus car.

CAN dependence
  • The cluster gets tach and coolant temperature from the engine computer over CAN
  • ABS/VSC also uses engine data
Low confidence1610
86 LS3 harness
  • Tach, coolant, CEL, speedometer and traction lights working
  • ABS kept or disabled
  • Push-start supported
Sourced · medium12
CAN module (2013-2019)
  • Tach, coolant gauge, CEL, fan and A/C control, ABS retained
  • Needs GM pressure sensor 22678731
Sourced · medium10

Forum work from 2015 traced the cluster's tach and coolant gauge to messages from the factory engine computer, and found the VSC/ABS unit also uses engine data. Remove that computer without replacing its messages and gauges, warning lamps and assist systems misbehave.Low16

Wiring Specialties' 86 LS3 harness says it keeps the tach, coolant gauge, check-engine light, speedometer and traction lights working. Buyers choose to keep ABS working or disable it, and disabling it limits the cluster. Its separate CAN module for the GM E38 computer lists the same gauges plus fan and A/C control on 2013-2019 cars.Medium1210

The 86 has electric power steering. Wiring Specialties says its assist works but varies when the ABS controller is retained, and Sikky says its turnkey cars keep working steering, so ask your harness maker exactly how assist behaves with your setup.Medium1126

Push-button start is supported on Premium cars, but the GM computer's own anti-theft must be disabled in its calibration before the engine will start. GM-computer harnesses come with a startup calibration that handles this.Medium1211

Chassis

Published builds show the stakes.

Stock torque151 lb-ft at 6,400 rpm, Subaru's 2013 rating205 NmSourced1
Brakes (2013 BRZ)
  • 11.6 in vented discs front and rear
  • 4-channel ABS with EBD and VSC
Sourced1
Rear axles
  • A known weak point on lowered cars with wide wheels
  • Grease spray warns of failure
Low confidence17

Motor1 covered a BRZ that went to an LS3 and T56 after its forced-induction boxer engines failed repeatedly, and the article noted a strong fuel smell in the cabin, a reminder to pressure-test every fuel joint.Medium15

Subaru rated the FA20 at 151 lb-ft, while GM's LS engines make far more torque. The factory Torsen differential, rear axles and soft diff bushings were sized for the boxer, and no maker publishes a torque rating for them, so treat the rear driveline as a planned upgrade.Medium120

Even stock-engine 86 owners report popped rear axles on low cars with wide wheels, with grease sprayed under the car as the warning sign. Carry a spare axle, inspect the boots after track days, and avoid extreme ride heights.Low17

Bolt-in diff braces such as Cusco's replace the job of the rubber diff mounts, which deflect under hard acceleration. Expect more drivetrain noise in the cabin. Upgrade brake pads and fluid for the extra speed the V8 brings.Low181

Tuning

Common setup

GM computer with a swap calibration, or a standalone ECU that can speak 86 CAN

Sourced · medium612
Base calibration
  • Startup calibrations remove anti-theft, EVAP, rear O2 and purge
  • Fuel tuning is not included
Sourced · medium12

Most LS 86 builds keep a GM computer re-calibrated for the swap, with Sikky's turnkey cars listing a GM computer and a standalone option. A standalone ECU is only practical here if it can send the CAN messages the cluster, ABS and steering expect.Medium612

Harness makers' startup calibrations only get the engine running: they remove anti-theft, EVAP, rear O2 and purge functions, and do not include fuel or timing work. Book a calibration session with a wideband logging lambda under load.Medium1211

Log knock activity, oil pressure and coolant temperature on the first drives. Make any ignition changes in small steps with knock monitoring, and leave timing values to an experienced calibrator.Low12

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 24 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Check the law and choose the parts
    Confirm what your region requires, then pick the engine, gearbox, mount kit and an 86-specific harness that supports your engine and computer.
  2. Remove the FA20 and gearbox
    Drain fluids, label connectors, and lift out the boxer, TL70 or automatic, driveshaft and exhaust.
  3. Fit pan and mounts to the LS
    Install the front-sump pan, pickup and remote filter adapter, then bolt the engine brackets to the block.
  4. Install engine and gearbox
    Lower the engine and gearbox together, fit the transmission mount, and torque all mount bolts to the kit values.
  5. Driveshaft, clutch and shifter
    Fit the new driveshaft and clutch master cylinder kit, bleed the clutch, and check the shifter position.
  6. Exhaust and brake lines
    Reroute the rear brake lines, fit the headers and join them to the cat-back with O2 sensors installed.
  7. Cooling and fuel
    Fit the radiator, fans, hoses and steam vent, then the pump, regulator and lines; leak-check under pressure.
  8. Wire the car
    Connect the engine harness, CAN module, pedal, fans and A/C, and route the battery cable to the starter.
  9. First start and checks
    Start on the startup calibration, then confirm gauges, ABS/VSC, steering assist, fans and the speedometer.
  10. Calibrate and shake down
    Tune with wideband logging, recheck mounts and driveshaft bolts, and inspect axles and diff mounts after the first drives.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Warning lamps and dead gauges after first startThe cluster and ABS/VSC listen for factory engine-computer CAN messages that the GM computer does not send.Use an 86-specific harness with CAN integration or a CAN module that translates the GM data, and decide early whether ABS stays active.Medium161210
Engine cranks but will not startThe GM computer's own anti-theft is still active in the donor calibration.Have the harness maker or calibrator disable anti-theft in the startup calibration before first start.Medium1211
Speedometer reads zero with a CD009Some swap gearboxes, including the Nissan CD009, have no speed sensor the GM computer and cluster can use.Add a GPS speed source or signal interface as the harness maker suggests, such as a Dakota Digital signal conditioner.Medium12
Transmission mount does not suit the chosen gearboxSikky's Stage 1 mount is listed for the T56, T56 Magnum and TR6060, while the CD009 is a separate option.Confirm the exact mount, driveshaft and adapter part for your gearbox before ordering the kit.Medium35
Rear brake lines too close to the headersThe 86 headers pass near the factory rear brake lines.Fit a reroute kit such as Sikky's HLK-07 before the first drive.Medium5
Grease sprayed under the car or popped rear axlesThe rear axles and diff mounts were sized for the FA20's 151 lb-ft, and low ride heights add angle.Inspect boots after hard use, carry a spare axle, avoid extreme drops and consider a diff brace.Low17181

Frequently asked

Does an LS fit in a BRZ, FR-S or 86?

Yes. Sikky and ICT Billet sell bolt-in mount kits for the 2013-2020 cars, and both depend on a front-sump oil pan. Sikky adds a pan, headers, a transmission mount and a driveshaft. A GTO LS2 mock-up was also reported to clear the stock hood, but check hood clearance with your own intake.Medium3914

What transmission do you use for an LS swap FR-S?

Most builds use a GM-pattern manual. Sikky lists the T56, T56 Magnum, TR6060 and Nissan CD009, each with a matching mount and driveshaft, and its turnkey service also lists the 4L60E. The factory TL70 manual does not bolt to the LS. Confirm the mount part for a CD009, because Sikky lists it separately.Medium362

Will the gauges, ABS and power steering work after an LS swap?

They can, with the right wiring. The 86 cluster and ABS/VSC expect CAN messages from the factory engine computer. Wiring Specialties' 86 harness and CAN module keep the tach, coolant gauge and check-engine light working and let you keep ABS. Electric steering assist is retained, though the harness maker says it varies when ABS stays.Medium121016

Will the stock BRZ differential hold an LS?

Treat it as a weak link. Subaru rated the stock engine at 151 lb-ft and fitted a Torsen limited-slip differential, but no maker publishes a torque limit for it. The rear axles already fail on some lowered stock cars. Plan a stronger rear driveline, or drive gently and inspect it often.Low117

Is an LS swapped BRZ street legal?

It depends on where you live. In the US, EPA expects an engine of the same or newer model year with its emission controls, which few used LS engines meet in a 2013-2020 car. California requires a BAR Referee inspection. The UK, Germany and Australia need registration updates or inspections. This is general information, not legal advice.Medium2324252627

Can I use an LS1 in an 86?

Yes, but it needs a cable-throttle conversion. Sikky's turnkey build starts from a used LS1 and T56, and Wiring Specialties sells an 86 LS1 harness for 1999-2002 car and 1999-2004 truck engines. The LS1 is drive-by-cable, so the 86's electronic pedal is replaced with a cable pedal.Medium611

Related

Sources

28 sources
  1. 2013 Subaru BRZ Specifications · Subaru of America (media site) · oem · retrieved 2026-10-27
  2. Toyota 86 · Wikipedia · reference · retrieved 2026-10-27
  3. Sikky Stage 1 Toyota 86 / Scion FRS LS Package (MK012-FRS) · Sikky Manufacturing · vendor-doc · retrieved 2026-10-27
  4. Sikky Stage 2 Scion FRS / Toyota 86 LS Package (w/ Headers) (MK012-2-FRS) · Sikky Manufacturing · vendor-doc · retrieved 2026-10-27
  5. Sikky Spec Your Own Toyota 86 / FRS LS Swap Kit (MK012L) · Sikky Manufacturing · vendor-doc · retrieved 2026-10-27
  6. Toyota 86 / Subaru BRZ turnkey LS swap · Sikky Manufacturing · vendor-doc · retrieved 2026-10-27
  7. Sikky Manufacturing LSX Swap Oil Pan for 2017-2020 86, 2013-2020 BRZ, 2013-2016 FR-S (OP009K) · Summit Racing · vendor-doc · retrieved 2026-10-27
  8. Sikky Toyota 86 / FRS, Subaru BRZ LSx Stage 2 Swap Kit · PASMAG · press · retrieved 2026-10-27
  9. Billet Aluminum LS Swap Engine Mount Kit FR-S BRZ GT86 · ICT Billet · vendor-doc · retrieved 2026-10-27
  10. FRS/BRZ with LS3 OEM E38 PCM CANbus DIY Module + A/C Support (WRS-RV2-FRS-LS3) · Wiring Specialties · vendor-doc · retrieved 2026-10-27
  11. FRS/BRZ/86 LS1 Swap Wiring Harness (CANBUS PRO Series) · Wiring Specialties · vendor-doc · retrieved 2026-10-27
  12. FRS/BRZ/86 LS3 58x DBW Swap Wiring Harness (Pro Series) · Wiring Specialties · vendor-doc · retrieved 2026-10-27
  13. Coming Soon: New LSX Swap Parts for FR-S and BRZ From Vorshlag (Oct 2016) · LSX Magazine · press · retrieved 2026-10-27
  14. Subaru BRZ LSX Swap In Progress (Dec 2012) · LSX Magazine · press · retrieved 2026-10-27
  15. Subaru BRZ With 500 HP LS3 V8 Swap Is As Wild As It Sounds (Oct 2021) · Motor1.com · press · retrieved 2026-10-27
  16. CAN BUS - for DIY swappers (thread, 2015) · FT86CLUB forum · community · retrieved 2026-10-27
  17. OEM Subaru Rear CV Axle for 2013-2021 Subaru BRZ/Scion FR-S/Toyota 86 · Battle Garage Racing Service · vendor-doc · retrieved 2026-10-27
  18. Cusco Rear Differential Brace - 2013-2024 Subaru BRZ, Scion FR-S, Toyota 86 & GR86 · Turn In Concepts · vendor-doc · retrieved 2026-10-27
  19. The KPower 86 Conversion Is Here (Aug 2021) · KPower Industries · vendor-doc · retrieved 2026-10-27
  20. General Motors LS-based small-block engine · Wikipedia · reference · retrieved 2026-10-27
  21. Tremec T-56 transmission · Wikipedia · reference · retrieved 2026-10-27
  22. LS3 EFI Crate Engine Specifications and Installation Instructions (19419889) · Chevrolet Performance (hosted by Speedway Motors) · oem · retrieved 2026-10-27
  23. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  24. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-27
  25. Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-25
  26. StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  27. VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25
  28. Executive Order D-126-32: GM LS3 E-ROD engine kit · California Air Resources Board · standard · retrieved 2026-10-25