At a glance
The key numbers and parts, with the source on each tile.
- VQ35DE 3.5 L V6: Nissan rated 287 hp at 6,200 rpm and 274 lb-ft for 2003-05371 N·m
- Manual Rev-up engines 300 hp
- The 2007-08 VQ35HR 306 hp at 6,800 rpm
About 3,188-3,247 lb (1,446-1,473 kg) for 2003-04 coupes, depending on trim
Sourced · medium7- LS1 and LS6 from the Camaro, Firebird, GTO and C5 Corvette
- LS3 for drive-by-wire builds
GM T56 or T56 Magnum with tunnel modification, or the factory CD00x 6-speed through an LS adapter plate and flywheel
Sourced · medium314- Bolt-in engine and transmission mounts with urethane bushings
- Each kit specifies its own baffled swap pan
- Viscous LSD on Enthusiast, Touring, Track and Nismo trims
- Base cars have none
- Tach, coolant temperature, check-engine lamp and fuel gauge are driven over CAN
- Plug-in swap harnesses add a CAN controller to keep them working
Recommended engines
- LS1 · Aluminum Gen III engine with a cable throttle; the dedicated Z33 plug-in harnesses for drive-by-cable engines are built around LS1-pattern sensors, and many mount kits were developed around it.
- LS6 · The C5 Z06 version of the Gen III aluminum engine; documented 350Z builds pair a salvaged LS6 with its matching T56.
- LS3 / L99 · Gen IV aluminum 6.2 L with a 58x crank trigger and drive-by-wire throttle; Z33 harness makers sell a separate DBW harness and pedal options for it.
- 5.3 LM7 / L59 / LY5 (Gen III/IV truck) · The budget junkyard choice; the iron block adds weight over the front axle compared with the aluminum LS1, LS6 and LS3.
Mounts
A 350Z LS swap starts with a mount kit, not fabrication.
Several makers sell engine and transmission mounts that bolt to the factory Z33 subframe, typically with billet or bent-steel pedestals and urethane bushings, so engine height and driveline angle are set by the kit.231
Buy the mounts and pan as a matched pair. The pan sump has to clear the Z33 crossmember at the height the mounts set, and at least one maker says common GTO pans and off-the-shelf aftermarket pans will not fit with its mounts.2
Swap pans are usually baffled with trap doors to stop oil starvation in long corners and drifting. Many builds also fit a remote oil filter mount, which frees space near the crossmember and gives spare ports for oil temperature and pressure senders.Medium18
Transmission
The GM T56 is the most common choice and most mount kits are designed for it.
- 6-speed manualFS6R31A, commonly called CD00x
- 5-speed automatic optional
- An F-body or GTO T56 puts the lever about 6-8 in forward of the stock opening150-200 mm
- A T56 Magnum about 8 in200 mm
Expect to modify the transmission tunnel to clear the bellhousing and case, and plan a shifter relocation because the lever lands well ahead of the Nissan console opening.31
The TR6060 is not a bolt-in. One kit maker notes that its rear bushing does not line up with the case holes, so a custom mount bracket is needed, and the shifter position is wrong for the Z33 without a custom shifter.3
Keeping the factory CD00x avoids tunnel work and keeps the stock shifter location. Adapter kits bolt the LS to the Nissan case with a dedicated flywheel; one design reuses a Nissan clutch, while another keeps the GM clutch and needs the bellhousing trimmed and a T56-style slave. Treat vendor torque claims for the CD009 as unverified, since Nissan publishes no rating.Medium14
Clearance
The tunnel is the main clearance job on a T56 build.
Mock up the engine and gearbox before final welding or sealing, and check the shifter path through all six gates once the console is back in.Medium31
Under the car, the swap pan, headers and Y-pipe set ground clearance. Some header designs are built for extra ground clearance and bolt to the factory Y-pipe location, which keeps the lowest point close to stock.Medium21
Cooling
For street use with a mild engine, the factory radiator can be enough.
For track days, drifting or a built engine, budget for a thicker aluminum radiator and a shroud that pulls air across the whole core.Medium1
Plumb the LS steam port back into the cooling system at a high point rather than capping it, so trapped air bleeds out of the heads. Adapt the heater hoses to the Nissan core and bleed the system carefully on first fill.Medium12
Decide early who controls the fans. Plug-in harnesses can hand fan control to the factory body electronics, while a standalone setup switches the fans through relays or power module outputs based on coolant temperature.Medium56
Fuel
Size the pump to the engine and power goal rather than reusing the VQ pump by default.
Documented builds use a higher-flow in-tank pump, a filter and a line kit that joins the Nissan hard lines to the LS rail. Use the fuel pump flow calculator to check capacity.Medium8
Match the regulator to the fuel strategy. Returnless LS rails expect regulation near the tank, while a return-style system needs a regulator and return line in the engine bay. Keep the evaporative canister connected if the car must pass inspection.Medium1216
Exhaust
The Z33 has more exhaust options than most LS swap chassis.
Headers that meet the factory Y-pipe let you keep the stock catalysts and cat-back, or move to a matched Y-pipe and cat-back from the same maker.Medium21
Long-tube headers flow more but usually need custom mid-pipes and can lower ground clearance. Check header tubes against the steering shaft, mounts and starter at mock-up, and keep catalysts where your jurisdiction requires them.Medium91
Electrical
The Z33 cluster listens to the CAN bus, so a GM engine harness alone leaves the tach and temperature gauge dead.
- Tach, coolant temperature, check-engine lamp, speedometer and fuel gauge run on the Z33 CAN bus
- There is no simple tach wire
- Gen III: 24x crank, rear cam sensor, 12 V sensors
- Gen IV: 58x crank, front-cover cam sensor, 5 V sensors
Builders either fit a harness with a CAN interface that translates engine data for the cluster, or mount separate gauges, often in the three 52 mm dash pods.Medium5111
Plug-in harness routes depend on the factory body harness, body control module and fuse boxes staying unmodified, because they reuse Nissan relays. Expect traction and stability control to stop working, and expect the oil pressure gauge to need the Nissan sender relocated to an adapter.Medium5
Mount a standalone ECU in the cabin, behind the glovebox or in the passenger footwell, away from heat and water. A power distribution module (PDM) or relay box nearby switches the pump, fans and ignition feeds, each fused to its wire. Safety: fit a fused main feed and battery-to-starter cable, and disconnect the battery before working on them.Low65
Chassis
The rear end was built for a V6, and base cars have no limited-slip at all.
- Viscous LSD on Enthusiast, Touring, Track and Nismo trims
- Base cars have an open differential
- An R200 variant shared with the G35 and 370Z/G37
- Forum reports say earlier R200s from the 300ZX and 240SX are not interchangeable
- Open-diff cars use equal-length half shafts
- VLSD cars use staggered lengths
Budget for a differential plan as part of the swap, whether that is a clutch-type or gear-type LSD in the factory housing or a stronger unit with matching axles.Low710
Check part compatibility closely. Owners report that the Z33 unit differs from older Nissan R200s in splines, ring and pinion, cover studs and flange position, and that VLSD and open cars use different axle lengths, so an LSD swap can also mean new axles or stub axles.Low10
Driveshafts for the swap are built around the chosen gearbox. Kit shafts use larger, serviceable U-joints, and the longer G35 coupe needs an aluminum or carbon fiber shaft to stay below its critical speed.Medium13
Tuning
With a donor GM computer, the minimum is a startup calibration that disables the GM anti-theft and removes outputs the chassis no longer has, such as the rear oxygen sensors and evaporative purge where that is legal. A standalone ECU gives more freedom but needs a full calibration, starting with fuel delivery and idle.Medium56
Gen IV engines with Active Fuel Management need it disabled in calibration or hardware. Drive-by-wire engines need the pedal and throttle body calibrated together, with the throttle safety checks left enabled.Medium136
Log with a wideband oxygen sensor before any loaded pulls, confirm knock control is active, and set a conservative rev limiter. Ignition timing should change in small steps with knock monitoring, never copied from another car.Low14
Legal
This is general information, not legal advice.
EPA treats an engine switch as reasonable if the result matches a certified configuration of the same or newer model year and the same product category
Sourced15Under EPA's 2020 tampering policy, a GM engine in a Nissan chassis rarely matches a certified configuration. California adds a BAR Referee inspection, and the E-ROD executive order covers only 1995 and older vehicles, so the Z33 has no packaged shortcut.151617
In the UK, an engine or cylinder-capacity change must be recorded on the V5C, and your insurer will treat it as a modification. In Germany, a change that alters the vehicle type or worsens emissions or noise voids the operating permit under StVZO §19 until an inspector approves it.Medium1819
In Australia, VSB 14 Section LA sets the technical rules for engine substitution, with certification run by each state. A V8 in the Z33 will normally need an engineer's sign-off covering brakes, emissions and noise.Medium20
Parts checklist
Tick what you have; the list is saved in this browser.
Order of work
10 stages, in the order most builds follow.
- Check the law and choose the gearboxConfirm what your state or country allows, then decide between a GM T56 with tunnel work or the factory CD00x with an adapter, because that choice sets mounts, driveshaft and clutch.
- Pick the engine generation and harnessChoose Gen III cable-throttle or Gen IV drive-by-wire, then buy the matching harness, gauge interface and pedal so triggers and throttle type agree.
- Prepare the engine on a standFit the swap pan and pickup, remote filter mount, flywheel or adapter plate, clutch and starter, and set up the accessory drive.
- Remove the VQ and prepare the chassisPull the engine and gearbox, then modify the tunnel if you are fitting a T56 and clean up the bay while access is good.
- Install engine and transmissionLower the drivetrain in with a hoist and helpers, bolt up the mounts, then fit the shifter, clutch hydraulics, driveshaft and power steering lines.
- Build cooling and fuelMount the radiator and fans, plumb the steam port and heater, then fit the pump, filter, regulator and rail lines.
- Fit the exhaustInstall headers, Y-pipe or mid-pipes, catalysts and hangers, checking clearance to the steering shaft and floor.
- Wire engine, gauges and powerMount the ECU in the cabin, run fused feeds and grounds, connect pump and fan control, the pedal, the CAN gauge interface and the speed signal.
- First start and leak checkPrime oil and fuel, check for leaks, confirm trigger sync and gauge readings, then bleed the cooling system.
- Calibrate and shake downLog with a wideband, verify knock control and temperatures, and build load gradually before road or track use.
Common problems
Symptom, cause and the usual fix.
| Problem | Cause | Fix |
|---|---|---|
| Tach and temperature gauge dead after the swap | The Z33 cluster reads these values from the CAN bus, which a GM harness does not drive. | Fit a harness with a CAN interface for the cluster, or install separate gauges.Medium511 |
| Engine cranks but will not start on a donor GM computer | The GM anti-theft (VATS) is still active in the calibration. | Load a startup calibration with the anti-theft disabled before first start.Medium5 |
| Oil pan hits the crossmember or engine sits too high | A pan that is not matched to the mount kit, such as a GTO or generic aftermarket pan. | Use the pan the mount maker specifies.2 |
| Shifter lands under the dash or radio | The GM T56 lever sits 6-8 in (150-200 mm) ahead of the Z33 opening. | Fit a shifter relocation kit or a Magnum XL case, or keep the CD00x through an adapter.31 |
| Speedometer reads zero | No usable speed signal reaches the cluster with the chosen gearbox and harness. | Add a signal conditioner or GPS-based speed source as the harness maker specifies.Medium6 |
| TR6060 will not bolt to the transmission mount | The TR6060 case holes do not line up with a mount designed for the T56. | Fabricate a custom mount bracket and shifter, or choose a T56.3 |
Frequently asked
Can you keep the CD009 on a 350Z LS swap?
Yes. Adapter kits mate a Gen III or Gen IV LS to the factory CD00x 6-speed with a billet plate and matched flywheel, which keeps the stock shifter location and avoids tunnel work. Some designs need the integral bellhousing trimmed. Nissan publishes no torque rating for the gearbox, so treat vendor strength claims with caution.Medium14
Does the 350Z gauge cluster work after an LS swap?
Only with a CAN interface or replacement gauges. The Z33 cluster reads tach, coolant temperature, check-engine lamp and fuel level over the CAN bus, with no simple tach wire. Plug-in swap harnesses add a controller that drives these gauges, but they need the factory body electronics left intact, and traction and stability control still stop working.Medium511
Do you have to cut the tunnel for a T56 in a 350Z?
Yes. Kit makers state the transmission tunnel must be modified to clear the bellhousing and case of a GM T56, T56 Magnum or TR6060. The shifter also lands 6-8 in (150-200 mm) forward of the stock opening, so plan a relocation kit, or keep the factory CD00x through an adapter to avoid both jobs.3
Will the stock 350Z differential hold up behind an LS?
Plan to upgrade it. Base 350Zs have an open differential, and the viscous LSD on other trims was designed around the V6. Owners report the Z33 unit differs from older R200s and that LSD swaps may need different axles, so budget for a stronger LSD and matching axles as part of the swap.Low710
Can a drive-by-wire LS3 go in a 350Z?
Yes. Harness makers sell a Gen IV 58x drive-by-wire harness for the Z33 with a choice of GM truck, GM car or stock Z33 pedal. The 58x crank trigger and front cam sensor need a computer set up for Gen IV, and Active Fuel Management engines need that feature disabled.Medium61413
Is an LS-swapped 350Z smog legal in California?
It is difficult. BAR requires a Referee inspection, and the replacement engine must be the same or newer model year with all its emissions equipment. The GM E-ROD executive order only covers 1995 and older vehicles, so it does not help a 2003-08 Z33. Talk to a Referee center before buying parts.Medium1617
Related
Sources
20 sources
- Ultimate 350z LS Swap Guide · Drifted.com · press · retrieved 2026-10-27
- ISR LS Swap Mounts for Nissan 350Z Z33 (ISR-350-LSMB) · ICT Billet (ISR Performance product listing) · vendor-doc · retrieved 2026-10-27
- 350Z / G35 LSx BASIC Swap Kit - T56 Transmission · LOJ Conversions · vendor-doc · retrieved 2026-10-27
- LS Swap CD009: Affordable and Reliable Transmission Upgrade · G Force Performance Products · vendor-doc · retrieved 2026-10-27
- 350Z LS1 Wiring Harness · Wiring Specialties · vendor-doc · retrieved 2026-10-27
- 350Z LS3 58x DBW Wiring Harness · Wiring Specialties · vendor-doc · retrieved 2026-10-27
- Nissan 350Z · Wikipedia · reference · retrieved 2026-10-27
- Could This LS6 Swapped 350Z Make A Cool Racecar? · LSX Magazine · press · retrieved 2026-10-27
- Building An Affordable Dream Car: LS Swapped Nissan 350Z · LSX Magazine · press · retrieved 2026-10-27
- Rear diff questions (forum thread) · My350Z.com · community · retrieved 2026-10-27
- Tach wire for converter (forum thread) · My350Z.com · community · retrieved 2026-10-27
- Nissan 240SX LS V8 Engine Swap Guide Part 2: Let's Get Started · Speed Academy · press · retrieved 2026-10-25
- General Motors LS-based small-block engine · Wikipedia · reference · retrieved 2026-10-27
- Dialing In LS Sensors For Various Generations · EngineLabs · press · retrieved 2026-10-27
- Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
- Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
- Executive Order D-126-32: GM LS3 E-ROD engine kit · California Air Resources Board · standard · retrieved 2026-10-25
- Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-27
- StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
- VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25

