Cam sync (cam position signal)

cam position sensorCMPcam phase sensorsync signalhome signal

Cam sync is a signal from a sensor reading the camshaft, used by the engine controller to tell which half of the four-stroke cycle each cylinder is in. The crank turns twice per cycle, so crank position alone cannot separate the compression stroke from the exhaust stroke.12

How it works

A four-stroke engine completes one cycle every two crank revolutions, and the camshaft turns once in that time.

Any crank pattern repeats every revolution, so the controller sees the same signal at compression top dead center and at exhaust top dead center. The cam signal breaks the tie.21

The simplest cam target has one tooth per cam revolution. Others use several teeth of varied width, which lets the controller sync faster and, on engines with variable cam timing, measure cam angle. GM Gen IV LS engines, for example, use a 4x cam signal while Gen III uses 1x.Medium342

Cam sensors are usually Hall-effect or variable reluctance types, like crank sensors. The controller combines both: the crank gives precise angle and speed, and the cam says which revolution it is.Medium52

In tuning

Cam sync is required for sequential injection, coil-on-plug ignition timed per cylinder, and cylinder-specific knock control.

Without it, the controller can still run wasted spark and batch or paired injection from the crank signal alone.26

The cam tooth must not change state close to a crank reference tooth, or small timing variations can make the controller pick the wrong revolution. On engines with variable cam timing, check that cam movement across its full range does not push the cam edge into that zone.Medium2

Myths vs facts

Myth The cam sensor sets ignition timing.

Fact Timing angle comes from the crank wheel. The cam signal only identifies the engine phase, plus cam angle on engines with variable valve timing.21

Myth An engine cannot run without a cam sensor.

Fact Many engines run on crank signal alone with wasted spark and batch injection. Sequential strategies and VVT control need the cam signal.26

Frequently asked

What does a cam position sensor do?

It tells the engine controller where the camshaft is, which identifies which stroke each cylinder is on. The controller needs that to fire injectors and coil-on-plug coils in sequence. On engines with variable valve timing, the same signal measures actual cam angle so the controller can control the phaser.27

Why do you need a cam sensor for sequential injection?

Sequential injection times each injector to its own cylinder's intake stroke. Because the crank turns twice per cycle, the crank signal alone looks the same on the intake and power halves of the cycle. The cam turns once per cycle, so its signal tells the controller which half it is in.21

What is the difference between crank and cam sensors?

The crank sensor reads a wheel on the crankshaft and gives precise engine speed and angle. The cam sensor reads a target on the camshaft, which turns at half crank speed, and gives engine phase. The controller needs the crank signal to run at all and the cam signal for sequential functions.52

What are the symptoms of a bad cam sensor?

Symptoms include long cranking before start, a check-engine light with a cam position code, rough running and, on engines with variable valve timing, a cam timing fault with reduced power. Many controllers fall back to a crank-only or default mode, so the engine may still run poorly rather than stop.Medium12

Wiring, pinouts and parts

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Crankshaft position sensor · Wikipedia · reference · retrieved 2026-10-25
  2. Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-25
  3. Dialing in LS sensors for various generations · EngineLabs · press · retrieved 2026-10-25
  4. Engine swapping a Gen IV in place of a Gen III · LSX Magazine · press · retrieved 2026-10-25
  5. Crankshaft speed sensor product data sheet · Robert Bosch GmbH · vendor-doc · retrieved 2026-10-25
  6. Wasted spark · Wikipedia · reference · retrieved 2026-10-25
  7. Variable valve timing · Wikipedia · reference · retrieved 2026-10-25