Sensor type · Variable reluctance (VR, AC) · Hall effect (digital) · Optical (digital)

Crankshaft position sensor (VR vs Hall)

CKP sensorcrank sensorcrank angle sensorCASengine speed sensor

A crankshaft position sensor reads teeth on a trigger wheel so the ECU knows engine speed and crank angle. Two-wire variable reluctance (VR) sensors generate an AC voltage that grows with speed and need no power. Three-wire Hall sensors need a supply and output a clean on/off square wave even at standstill.231

Parts in the library

Support across ECUs

Across the 12 parts in this hub (6 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU22 configurable (generic input) · 10 to be confirmed
Haltech (Elite / Nexus)11 configurable (generic input) · 1 unverified
Link (G4X)9 configurable (generic input) · 3 unverified
MoTeC (M1)12 unverified
ECUMaster (EMU Black)11 configurable (generic input) · 1 unverified
AEM (Infinity)11 configurable (generic input) · 1 unverified
MaxxECU11 configurable (generic input) · 1 unverified
Holley (Terminator X / EFI)7 configurable (generic input) · 5 unverified

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

A VR sensor is a magnet with a coil. Each passing tooth changes the magnetic flux and induces a voltage, so the signal amplitude rises with rpm and the ECU reads the zero crossings. Bosch notes inductive sensors need some rotational speed to produce a measurable voltage.21

A Hall sensor switches a transistor when a ferromagnetic tooth passes. Bosch's Mini-HA-P is an example: 5-18 V supply, open-collector output for a 1 kΩ pull-up, active low, up to 10 kHz.3

A missing-tooth pattern such as 60-2 marks a reference angle. The Bosch IS-C inductive sensor data sheet specifies its test wheel as 60-2 teeth with a 0.8 ± 0.3 mm air gap.2

Types and variants

Variable reluctance (2-wire)Variable reluctance (VR, AC)

Self-generating AC signal, coil resistance in the hundreds of ohms (340 Ω for the Bosch IS-C). Needs an input with an adaptive or zero-crossing threshold.29

Hall effect (3-wire)Hall effect (digital)

Needs supply and ground; digital output with an open collector that needs a pull-up. Reads from zero rpm.3

Optical crank angle sensorOptical (digital)

A slotted disc and LEDs in a cam-driven unit, used on several Nissan engines; gives crank and cam signals from one housing.Low45

Wiring

Run VR crank wiring as a twisted pair inside a shield, with the shield drained to sensor ground at the ECU end only. A shield grounded at both ends forms a loop that can carry noise current.Medium107

Keep crank wiring away from coil and injector wiring. GM bulletin 17-NA-317 fixed crank-signal faults on 2018 Buick Enclave and Chevrolet Traverse (LFY engine) by replacing the harness section with a twisted-pair jumper, because the circuit picked up interference from another circuit in the same harness.6

VR polarity matters: if the two wires are reversed, the ECU sees the zero crossing on the wrong edge and the trigger angle shifts. Check the waveform on a scope at cranking speed.Medium91

Connector and wiring library

Common faults and checks

Cranks but no rpm signal

Likely cause Open sensor or wrong sensor type for the input (a Hall sensor with no pull-up or supply)

Check VR: measure coil resistance across the two pins. Hall: confirm supply and ground at the connector and that the input has a pull-up.Medium23

Misfire-like stumble or false rpm spikes at high load

Likely cause Electrical noise coupled into the crank circuit

Check Check shield continuity and the drain at the ECU end only; route away from ignition wiring. GM addressed one case with a twisted-pair jumper harness.Medium610

Timing drifts with rpm

Likely cause Reversed VR polarity or excessive air gap

Check Scope the signal and set the air gap to the sensor maker's range (0.8 ± 0.3 mm for the Bosch IS-C).Medium29

Frequently asked

Is my crank sensor VR or Hall?

Count the wires first: two wires usually means VR, three usually means Hall. Confirm with a meter. A VR sensor shows a coil resistance of a few hundred ohms across its pins and produces AC voltage when the engine turns; a Hall sensor needs a supply and switches between two levels.Medium23

Why does a crank sensor need shielded wire?

VR signals are small at cranking speed, so ignition noise can create false teeth. A twisted pair inside a shield, drained at the ECU end only, keeps induced noise low. GM has issued a bulletin that cured crank faults with a twisted-pair harness.Medium610

Can a VR sensor read engine speed at zero rpm?

No. A VR sensor generates voltage only when teeth move past it, and Bosch notes inductive sensors need a basic rotational speed. A Hall sensor reads tooth or gap at standstill.21

What air gap does a crank sensor need?

Use the sensor maker's figure. Bosch specifies 0.8 ± 0.3 mm for the IS-C inductive sensor and 0.2-1.5 mm for the Mini-HA-P Hall sensor. Too large a gap weakens a VR signal at cranking.23

Related

Use it with GAINS

Crankshaft position sensor on GAINS hardware

ECU2CRANK (VR or Hall, single-ended, adaptive threshold)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable with the shield to sensor ground at the ECU. The pull-up arrangement for Hall sensors on this pin is to be confirmed in the schematic.Medium7

The CRANK input accepts VR or Hall single-ended with an adaptive threshold, so most factory sensors connect without an external conditioner.7

GAINS hardware is pre-release concept design. Pin numbers come from the ECU2 v0.3 pin map and the PDM2 specification and can change before release; none of it has been tested on a vehicle yet.78

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

10 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Inductive Speed Sensor IS-C data sheet · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. Speed Sensor Hall-Effect Mini-HA-P sealed data sheet 69875339 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. sensors/Nissan RB family: RB CAS/MAF/knock numbers · ebay.de · vendor-doc · retrieved 2026-10-25
  5. sensors/Nissan knock 22060-30P00 and SR CAS: 22060-30P00 SR/KA/VG; SR CAS disk · walmart.com · vendor-doc · retrieved 2026-10-25
  6. Service Bulletin 17-NA-317: crankshaft position sensor circuit EMI, twisted-pair jumper harness (Feb 2020) · General Motors (via NHTSA) · oem · retrieved 2026-10-27
  7. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  8. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  9. LM1815 adaptive variable reluctance sensor amplifier data sheet · Texas Instruments · vendor-doc · retrieved 2026-10-27
  10. Shielded cable · Wikipedia · reference · retrieved 2026-10-27