Top dead center (TDC)

TDCtop dead centreTDC compressionBTDCATDC

Top dead center (TDC) is the crankshaft position where a piston is at the very top of its stroke, farthest from the crankshaft. It is the zero reference for ignition timing, cam timing and crank angle, which are quoted in degrees before (BTDC) or after (ATDC) TDC.36

How it works

Top dead center is where the connecting rod lines up with the crank throw, so piston motion briefly stops and reverses.

Bottom dead center (BDC) is the opposite point. Near TDC the piston barely moves for a few degrees of crank rotation, which is why finding true TDC by eye is inaccurate.Medium32

A four-stroke cycle takes 720 crank degrees, so each piston passes TDC twice per cycle. Compression TDC is where the spark fires. Overlap TDC, at the end of exhaust, is where both valves are open.

Cylinder 1 compression TDC is the usual reference.23

Ignition advance is quoted in crank degrees BTDC, and firing after TDC is called ATDC. Cam events, injection timing and trigger offsets all use the same reference, so an error in TDC shifts every one of them by the same amount.63

Typical values

Four-stroke cycle720crank degreesTwo crank turns; one cam turnSourced2
Compression vs overlap TDC360 crank degrees apartCrank alone cannot tell them apart; the cam canSourced23
Inline-4 TDC pairsCylinders 1/4 and 2/3, pairs 180 degrees apartSourced3
Wasted-spark pairsCylinders 360 crank degrees apart share a coile.g. 1/4 and 2/3 on an inline-4Sourced5
Cam to crank ratio1 cam degree = 2 crank degreesSourced2

How an ECU uses it

The ECU never sees TDC directly.

It sees crank trigger teeth and a cam sync signal, then uses a calibrated trigger offset (the angle between a reference tooth and cylinder 1 TDC) to place every spark and injection event.Medium15

If that offset is wrong, every cylinder's actual timing differs from the commanded timing by the same error. The ECU cannot detect this itself, which is why the offset must be verified with a timing light against a true TDC mark.Medium61

The cam signal tells the ECU which crank revolution is compression TDC. Without it, the ECU can only run wasted spark and batch or paired injection, because it cannot tell compression TDC from overlap TDC.Medium52

How to test it

4 checks, in order.

  1. Safety
    disable ignition and fuel before turning the engine by hand, and never crank the starter with a piston stop fitted. A stop in the plug hole can damage the piston or valves.Low3
  2. Find compression TDC on cylinder 1 roughly: remove the plug, cover the hole and turn the crank by hand until compression pushes out; then line up the factory mark on the balancer or flywheel.Medium3
  3. For true TDC, fit a degree wheel and a positive piston stop in the plug hole. Turn the crank each way until the piston touches the stop and note both readings; true TDC is exactly halfway between them. Correct the pointer to read zero there.Low32
  4. Verify the ECU: lock timing to a fixed value in the software, start the engine and check with a timing light on the verified mark. Adjust the trigger offset until the light reading matches the commanded value.Medium61

Symptoms and causes

Timing light reading differs from logged timing

Likely causes Wrong trigger offset, slipped damper outer ring, wrong pointer

Check Verify true TDC with a piston stop and degree wheel, then recheck

Medium63

Engine cranks but will not start after a swap

Likely causes Cam sync set 360 degrees out, so spark fires on overlap TDC

Check Check that cylinder 1 is on compression when the ECU shows TDC

Medium25

Knock on all cylinders at modest load

Likely causes Actual timing more advanced than commanded due to offset error

Check Timing light check at locked timing

Medium64

In tuning

Verify TDC and trigger offset before any timing work.

A small offset error looks like a fuel or knock problem and makes every timing number in the map wrong by the same amount.Medium61

Harmonic balancers with rubber-bonded outer rings can slip, moving the timing mark. On any older or rebuilt engine, confirm the mark with a piston stop rather than trusting the pulley.Low3

Common mistakes

Mistake Finding TDC by watching the piston through the plug hole.

Do instead The piston dwells near TDC for several degrees; use a positive stop and degree wheel and split the difference.Medium32

Mistake Setting the trigger offset on overlap TDC instead of compression TDC.

Do instead Confirm cylinder 1 valves are both closed at the reference point before setting the cam sync and offset.Medium2

Mistake Checking timing with the ECU still adjusting it.

Do instead Lock timing in the software first, otherwise idle control and corrections move the reading.Medium61

Myths vs facts

Myth The timing mark on the pulley is always correct.

Fact Marks can be wrong after a balancer slips or the wrong pulley is fitted. Only a piston stop and degree wheel prove true TDC.Medium3

Myth TDC happens once per cycle.

Fact Each piston reaches TDC twice in a four-stroke cycle: once at compression and once at the end of exhaust. Only the compression TDC fires the spark.2

Frequently asked

What does top dead center mean?

Top dead center is the crank position where a piston reaches the top of its stroke and momentarily stops. It is the zero point for measuring ignition timing, cam timing and crank angle, quoted in degrees before or after TDC.36

What is the difference between BTDC and ATDC?

BTDC means before top dead center and ATDC means after it, both in crankshaft degrees. Spark advance is normally given BTDC, because the flame needs time to build pressure; firing ATDC is usually reserved for special cases.6

How do you find TDC on cylinder 1?

Remove the plug, turn the engine by hand until compression pushes out of the hole, then line up the factory timing mark. For true TDC, use a degree wheel and positive piston stop, read both sides and take the midpoint.Medium3

How do you know if you are on the compression stroke?

On compression TDC both valves for that cylinder are closed and you feel pressure at the plug hole as the piston rises. On overlap TDC the exhaust is closing and the intake opening, so the rockers move and there is no pressure.Medium27

Why does TDC matter for an ECU?

The ECU places every spark and injection using a trigger offset from cylinder 1 TDC. If that offset is wrong, the real timing differs from the commanded timing on every cylinder, so it must be checked with a timing light.Medium61

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-27
  2. Internal Combustion Engine Fundamentals, 2nd edition (J. B. Heywood) · McGraw-Hill Education · book · retrieved 2026-10-27
  3. Dead centre (engineering) · Wikipedia · reference · retrieved 2026-10-27
  4. Engine knocking · Wikipedia · reference · retrieved 2026-10-27
  5. Ignition system · Wikipedia · reference · retrieved 2026-10-27
  6. Ignition timing · Wikipedia · reference · retrieved 2026-10-27
  7. Valve timing · Wikipedia · reference · retrieved 2026-10-27