Sensor type · Hall effect (digital) · Variable reluctance (VR, AC) · Optical (digital)

Camshaft position sensor

CMP sensorcam sensorcam sync sensorcylinder identification sensor

A camshaft position sensor tells the ECU which half of the four-stroke cycle the engine is in, because the crank turns twice per cam revolution. With that phase signal the ECU can run sequential injection and coil-on-plug ignition. Cam sensors are VR or Hall types, wired like crank sensors, and also feed variable cam timing control.21

Parts in the library

Support across ECUs

Across the 5 parts in this hub (4 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU25 to be confirmed
Haltech (Elite / Nexus)5 configurable (generic input)
Link (G4X)5 configurable (generic input)
MoTeC (M1)5 unverified
ECUMaster (EMU Black)5 configurable (generic input)
AEM (Infinity)5 configurable (generic input)
MaxxECU5 configurable (generic input)
Holley (Terminator X / EFI)2 configurable (generic input) · 3 unverified

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

The crank wheel alone repeats every 360°, so a sequential engine needs a once-per-cycle reference from the cam. One pulse per cam turn is enough for phase; more teeth let the ECU measure cam angle for variable valve timing.1

Bosch lists its Mini-HA-P Hall sensor for camshaft, crankshaft and wheel speed measurement, the same sensor technology across all three jobs.2

On GM LS engines the cam signal changed between generations: Gen III used a single-pulse sensor at the back of the block, and Gen IV moved to a four-pulse sensor in the front timing cover.Medium5

Types and variants

Hall (3-wire)Hall effect (digital)

Most modern cam sensors; digital output from zero speed.2

VR (2-wire)Variable reluctance (VR, AC)

Used on some engines; same input requirements as a VR crank sensor.Medium1

Optical CASOptical (digital)

Some Nissan engines combine crank and cam signals in one optical unit on the cam.Low34

Wiring

Treat cam wiring like crank wiring: shielded where the sensor is VR, drain at the ECU end only, and routed away from ignition leads.Medium86

A Hall cam sensor needs a pull-up on its output if the sensor has an open-collector stage, as Bosch's Mini-HA-P does.2

Connector and wiring library

Common faults and checks

Starts only in batch or wasted-spark mode, or long cranking

Likely cause No cam phase signal

Check Log the cam input while cranking; expect the documented number of pulses per cam turn.Medium1

Cam timing control hunts

Likely cause Noisy or late cam edge

Check Scope cam and crank together and check the edge stays at a fixed crank angle at steady rpm.Medium1

Frequently asked

Do I need a cam sensor for sequential injection?

Yes. The crank turns twice per engine cycle, so without a cam reference the ECU cannot tell compression from exhaust stroke and falls back to batch injection and wasted spark.1

What is the difference between a 1X and 4X cam sensor on an LS?

Gen III LS engines used a single-pulse cam signal from a sensor at the back of the block. Gen IV engines use a four-pulse signal from a sensor in the front timing cover. The ECU must be set for the pattern the engine has.Medium5

Can one Hall sensor type serve crank, cam and wheel speed?

Often yes. Bosch markets the same Hall speed sensor for camshaft, crankshaft and wheel speed measurement, as long as the target wheel and air gap suit it.2

Related

Use it with GAINS

Camshaft position sensor on GAINS hardware

ECU2CAM (VR or Hall, single-ended)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

One cam input on the ECU2. Additional cam signals for dual VVT need a free digital input; mapping to be confirmed.Medium6

GAINS hardware is pre-release concept design. Pin numbers come from the ECU2 v0.3 pin map and the PDM2 specification and can change before release; none of it has been tested on a vehicle yet.67

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Speed Sensor Hall-Effect Mini-HA-P sealed data sheet 69875339 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. sensors/Nissan RB family: RB CAS/MAF/knock numbers · ebay.de · vendor-doc · retrieved 2026-10-25
  4. sensors/Nissan knock 22060-30P00 and SR CAS: 22060-30P00 SR/KA/VG; SR CAS disk · walmart.com · vendor-doc · retrieved 2026-10-25
  5. Dialing in LS sensors for various generations with Michigan Motorsports · EngineLabs · press · retrieved 2026-10-27
  6. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  7. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  8. Shielded cable · Wikipedia · reference · retrieved 2026-10-27

Not yet indexed: fewer than 4 FAQs.