Bosch · Hall effect (digital)
Bosch HA-M Hall-effect speed sensor (B261.209.283-01 / B261.209.295-01)
The Bosch HA-M is a metal-housed Hall-effect speed sensor for crank, cam or wheel speed, sold active low (B261.209.283-01) or active high (B261.209.295-01). It runs on 5-18 V, switches an open-collector output for a 1 kΩ load up to 4.2 kHz and needs a 0.5-1.5 mm air gap. Pins: 1 supply, 2 ground, 3 signal.2
Key specifications
Measures: Rotational speed from a ferromagnetic target wheel. Output: Hall effect (digital).
Pinout and connector
- Supply
- Ground / return
- Signal
- Shield
- Not used / not listed
| Pin | Function (as published) | Typical ECU input | Wire note |
|---|---|---|---|
| 1 | Supply (US) | Sensor supply (5-18 V per maker) | Red (flying-lead version) (published) |
| 2 | Ground | Sensor ground | Black (flying-lead version) (published); Return to sensor ground, not chassis |
| 3 | Signal | Crank/cam trigger input (digital, pull-up) | Green (flying-lead version) (published) |
Wire colours apply to the flying-lead version F02U.V00.627-01; connector versions use pins 1-3.2 The ECU-input and wire columns are our general guidance, not the maker's.
Connector: Autosport AS 3-way (ASU603-03PN-HE); mating part ASU003-03SN-HE (F02U.000.199-01)2 Connector library
Terminals and seals: Not listed: the data sheet gives the mating connector only.
How it's calibrated
ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.
Trigger setup
- Trigger type: Hall effect (digital square wave).2
- Output: Open collector for 1 kΩ; active low or active high by part number.2
- Max frequency: ≤ 4.2 kHz.2
- Air gap: 0.5-1.5 mm (0.020-0.059 in) to the target wheel.2
- Trigger edge: not published by the maker. Confirm the edge your ECU uses with a scope or a timing light before running the engine.
Native support across ECUs
| ECU platform | Status | How to set it up | Source |
|---|---|---|---|
| GAINS ECU2Concept | To be confirmed | INJ5-6 or IGN5-6 as a frequency input with the 2.2 kΩ pull-up, or CRANK/CAM (pins 13/15) for engine position; Hall pull-up on CRANK/CAM still open. | Medium3 |
| Haltech (Elite / Nexus) | Configurable (generic input) | One of the 6 synchronised pulsed inputs, which Haltech lists as usable for cam sensors or as frequency inputs; or the trigger/home inputs for engine position. | Medium5 |
| Link (G4X) | Configurable (generic input) | Trigger input; Link sells a Hall sensor kit listed for all Link ECUs. Wheel-speed input count not on the public page. | Medium6 |
| MoTeC (M1) | Unverified | The M150 page lists programmable digital inputs but does not name Hall speed sensors. | No public source |
| ECUMaster (EMU Black) | Configurable (generic input) | Vehicle speed input (Hall or VR), or one of 3 trigger inputs with Hall/VR selected in software. | Medium7 |
| AEM (Infinity) | Configurable (generic input) | Crank or cam Hall input (10 kΩ pull-up to 12 V per AEM's Series 5 spec). | Medium8 |
| MaxxECU | Configurable (generic input) | One of 4 extra digital/VR inputs listed for speed sensors, or a trigger input in digital mode. | Medium9 |
| Holley (Terminator X / EFI) | Unverified | Not checked: we cite only public product pages, and none for Holley covers this sensor. | No public source |
Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.
Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.
CAD and drawings
- Data sheetSpeed Sensor Hall-Effect HA-M data sheet 69827851 (PDF)2Download from Bosch MotorsportNo login at last check; the maker may change this
We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.
Wiring and installation
Supply to pin 1 (5-18 V), ground to pin 2 and pin 3 to a Hall or digital input with a pull-up. Pick active high or active low to suit which tooth edge your ECU expects.2
Use the sensor's own plug for mounting, avoid abrupt temperature changes and test any target wheel that differs from Bosch's reference dimensions.2
Failure modes and checks
Likely cause Air gap outside 0.5-1.5 mm
Check Measure the gap to the target wheel with feeler gauges and shim the sensor to Bosch's range.2
Likely cause No pull-up, or an ECU input expecting VR
Check The output is open collector rated for a 1 kΩ load: set the ECU input to Hall/digital with a pull-up to its supply.2
Likely cause Target wheel outside the tested dimensions, or tooth frequency above the rating
Check Bosch says a different wheel must be tested individually; check tooth count × speed stays under the frequency limit.Medium2
Test it with a multimeter
- With the supply connected and a pull-up on the signal, the signal pin should switch between near 0 V and the pull-up voltage as a tooth passes (turn the engine slowly). Maker output: Open collector for 1 kΩ; active low or active high by part number.2
Frequently asked
What is the pinout of the Bosch HA-M?
Pin 1 supply, pin 2 ground, pin 3 signal. On the flying-lead version the wires are red (supply), black (ground) and green (signal).2
Active high or active low: which HA-M do I need?
It depends on which edge your ECU or logger triggers on. Bosch sells B261.209.295-01 as active high and B261.209.283-01 as active low; the falling tooth edge is the one Bosch specifies for repeatability.Medium2
What air gap does the HA-M need?
Bosch specifies 0.5-1.5 mm to a ferromagnetic target wheel in its application table, with 0.5-1.0 mm quoted on the front page. Set it near the low end and confirm a clean signal on a scope.2
Related
Use it with GAINS
Bosch HA-M Hall-effect speed sensor (B261.209.283-01 / B261.209.295-01) on GAINS hardware
ECU2CRANK (VR or Hall, single-ended, adaptive threshold)
- Pins
- On the ECU2 pin map
- Pull-up
- To be confirmed
- Shielding
- Shielded, drain at the ECU end only
Shielded cable, shield to sensor ground at the ECU end only. Hall pull-up arrangement to be confirmed in the schematic.Medium3
GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34
Concept Pre-release hardware. Pin assignments come from the current design documents and may change.
Sources
9 sources
- Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-11-04
- Speed Sensor Hall-Effect HA-M data sheet 69827851 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-11-04
- internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
- internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
- Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-11-04
- Hall effect sensor kit product page · Link Engine Management · vendor-doc · retrieved 2026-10-27
- EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-11-04
- Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
- MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-11-04

