Bosch · Hall effect (digital)

Bosch HA-N Hall-effect speed sensor (F02U.V0U.714-01)

Bosch F02U.V0U.714-01Bosch F02U.V0U.714-90

The Bosch HA-N is a lightweight aluminium Hall-effect speed sensor, programmed active low, that Bosch says is approved for NASCAR as a camshaft sensor. It fits a 10 mm bore, runs on 5-18 V, switches an open-collector output for a 1 kΩ load up to 4.2 kHz and needs a 0.5-1.5 mm air gap. Pins: 1 supply, 2 ground, 3 signal.2

Key specifications

Measures: Rotational speed (cam, crank or wheel) from a ferromagnetic target. Output: Hall effect (digital).

OutputOpen collector for 1 kΩ, active lowSourced2
Max frequency≤ 4.2 kHzSourced2
Air gap0.5-1.5mm0.020-0.059 inThe front page quotes 0.4-1.5 mm.Sourced2
Supply5-18V, 5.6-18 mASourced2
Temperature-40 to 160°C-40 to 320 °FSourced2
Mounting
  • 10 mm bore, 14 mm installation depth, 6 N·m
  • 8 g without wire
Sourced2
Part numberMakerNote
F02U.V0U.714-01BoschHA-N with AS connector (254 mm lead)2
F02U.V0U.714-90BoschHA-N with 1,000 mm flying leads2

Pinout and connector

12345Schematic, pin-number order (positions not published)
Schematic in pin-number order: the maker does not publish cavity positions. Mating face labels. Pin functions from the maker's document. Our drawing from the published pin list, not a maker drawing.
  • Supply
  • Ground / return
  • Signal
  • Shield
  • Not used / not listed
Download pinout (SVG)
PinFunction (as published)Typical ECU inputWire note
1Supply (VS)Sensor supply (5-18 V per maker)WHT/ORG (flying lead) (published)
2GroundSensor groundWHT/BLU (flying lead) (published); Return to sensor ground, not chassis
3SignalCrank/cam trigger input (digital, pull-up)WHT (flying lead) (published)
4Not usedLeave unconnected—
5Not usedLeave unconnected—

Wire colours apply to the flying-lead version F02U.V0U.714-90.2 The ECU-input and wire columns are our general guidance, not the maker's.

Connector: Autosport AS 5-way (ASL606-05PA-HE); mating part ASL006-05SA-HE2 Connector library

Terminals and seals: Not listed: the data sheet gives the mating connector only.

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Trigger setup

  • Trigger type: Hall effect (digital square wave).2
  • Output: Open collector for 1 kΩ, active low.2
  • Max frequency: ≤ 4.2 kHz.2
  • Air gap: 0.5-1.5 mm (0.020-0.059 in).2
  • Trigger edge: not published by the maker. Confirm the edge your ECU uses with a scope or a timing light before running the engine.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedCRANK (pin 13) or CAM (pin 15) accept Hall in the concept; wheel speed goes on INJ5-6 or IGN5-6 as a frequency input. The Hall pull-up on CRANK/CAM is still open.Medium3
Haltech (Elite / Nexus)Configurable (generic input)One of the 6 synchronised pulsed inputs, which Haltech lists as usable for cam sensors or as frequency inputs; or the trigger/home inputs for engine position.Medium5
Link (G4X)Configurable (generic input)Trigger input; Link sells a Hall sensor kit listed for all Link ECUs. Wheel-speed input count not on the public page.Medium6
MoTeC (M1)UnverifiedThe M150 page lists programmable digital inputs but does not name Hall speed sensors.No public source
ECUMaster (EMU Black)Configurable (generic input)Vehicle speed input (Hall or VR), or one of 3 trigger inputs with Hall/VR selected in software.Medium7
AEM (Infinity)Configurable (generic input)Crank or cam Hall input (10 kΩ pull-up to 12 V per AEM's Series 5 spec).Medium8
MaxxECUConfigurable (generic input)One of 4 extra digital/VR inputs listed for speed sensors, or a trigger input in digital mode.Medium9
Holley (Terminator X / EFI)UnverifiedNot checked: we cite only public product pages, and none for Holley covers this sensor.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Supply to pin 1, ground to pin 2, signal on pin 3 to a Hall input with a pull-up; pins 4 and 5 are unused. On the flying-lead version, white/orange is supply, white/blue ground and white the signal.2

Failure modes and checks

No signal or missing pulses

Likely cause Air gap outside 0.5-1.5 mm

Check Measure the gap to the target wheel with feeler gauges and shim the sensor to Bosch's range.2

Signal stuck high and never pulls low

Likely cause No pull-up, or an ECU input expecting VR

Check The output is open collector rated for a 1 kΩ load: set the ECU input to Hall/digital with a pull-up to its supply.2

Erratic speed at high rpm

Likely cause Target wheel outside the tested dimensions, or tooth frequency above the rating

Check Bosch says a different wheel must be tested individually; check tooth count × speed stays under the frequency limit.Medium2

Test it with a multimeter

  • With the supply connected and a pull-up on the signal, the signal pin should switch between near 0 V and the pull-up voltage as a tooth passes (turn the engine slowly). Maker output: Open collector for 1 kΩ, active low.2

Frequently asked

What is the pinout of the Bosch HA-N?

Pin 1 supply, pin 2 ground, pin 3 signal; pins 4 and 5 are not used. The flying-lead version uses white/orange, white/blue and white wires for the same functions.2

Is the HA-N active high or active low?

Active low. Bosch programs the sensor element for an active-low open-collector output.2

Can the HA-N read wheel speed?

Yes. Bosch lists camshaft, crankshaft and wheel speed as applications, within its 4.2 kHz limit and a 0.5-1.5 mm air gap.2

Related

Use it with GAINS

Bosch HA-N Hall-effect speed sensor (F02U.V0U.714-01) on GAINS hardware

ECU2CRANK (VR or Hall, single-ended, adaptive threshold)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable, shield to sensor ground at the ECU end only. Hall pull-up arrangement to be confirmed in the schematic.Medium3

ECU2CAM (VR or Hall, single-ended)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable, shield to sensor ground at the ECU end only.Medium3

ECU2Digital/frequency input personality

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

For wheel speed: INJ5-6 or IGN5-6 as a frequency input with the 2.2 kΩ pull-up.Medium3

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

9 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-11-04
  2. Speed Sensor Hall-Effect HA-N data sheet 69988747 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-11-04
  3. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  4. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  5. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-11-04
  6. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-11-04
  7. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  8. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-11-04