Hall-effect sensor

Hall sensorHall effect pickupdigital crank sensoractive speed sensor

A Hall-effect sensor is an active semiconductor sensor that switches its output when a magnetic field crosses a threshold. In engines it reads trigger wheel teeth or magnets on crank, cam and wheel shafts, producing a clean square wave whose amplitude does not depend on speed, so it works down to zero rpm.9510

How it works

The Hall effect is a voltage that appears across a conductor carrying current in a magnetic field.

A Hall sensor chip amplifies that voltage and compares it with switching thresholds, so the output flips state as a tooth or magnet pole passes.109

Speed sensors for steel trigger wheels carry a back-bias magnet behind the Hall element. A passing tooth concentrates that field and a gap weakens it. Bosch's Mini-HA-P works this way with an air gap of 0.2 to 1.5 mm (0.008 to 0.059 in) and signals up to 10 kHz.39

Most automotive Hall sensors have three wires: supply, ground and signal. The output is usually open-drain or open-collector, meaning it can only pull the signal low. TI's DRV5013, for example, runs from 2.5 to 38 V and sinks up to 30 mA, so the ECU or harness must supply a pull-up resistor.59

Because the output is digital and speed-independent, a Hall sensor gives sharp edges at cranking speed and can report shaft position with the engine stopped. The trade-offs are the need for power and electronics that must survive engine-bay heat; the Mini-HA-P is rated to 150 °C (302 °F).913

Typical values

Supply range (TI DRV5013)2.5-38VSourced5
Output (TI DRV5013)open drain, sinks up to 30 mANeeds an external pull-upSourced5
Supply (Bosch Mini-HA-P)5-18 V at about 10 mASourced3
Output (Bosch Mini-HA-P)open collector, active low, specified with 1 kΩ pull-upSourced3
Air gap (Bosch Mini-HA-P)0.2-1.5mm0.008-0.059 inSourced3
Maximum frequency (Bosch Mini-HA-P)10kHzSourced3
Falling-edge repeatability (Mini-HA-P)under 3% to 6 kHz, under 5% to 10 kHzSourced3
Operating temperature-40 to 150°C-40 to 302 °FMini-HA-P; DRV5013 E gradeSourced35

How an ECU uses it

An ECU treats a Hall sensor as a digital input: a pull-up to its own 5 V or 12 V rail, a comparator with fixed thresholds and a timer that captures the chosen edge. No adaptive threshold is needed, because amplitude does not change with speed.Medium59

Edge choice matters. Bosch specifies repeatability on the Mini-HA-P's falling edge, its active-low switching point, so that edge is the better timing reference. The other edge sits a tooth width away and drifts more with air gap.Medium3

Because Hall sensors detect a static field, the ECU can read cam and crank position at standstill or very slow cranking. That supports quick-start strategies and steady cam phase measurement with variable valve timing.Medium19

How to test it

5 checks, in order.

  1. Identify supply, ground and signal from the data sheet or the sensor hub page. Back-probe with the connector plugged in, so the ECU's pull-up stays in the circuit.Medium5
  2. With the key on and engine off, measure supply to ground at the sensor; it should match the specified supply. Then measure from the sensor ground to battery negative; any significant voltage there means a poor ground.Medium53
  3. Turn the engine or shaft slowly by hand and watch the signal. It should switch cleanly between near 0 V and the pull-up voltage as teeth pass. Stuck at pull-up voltage suggests a dead sensor; stuck near 0 V suggests a short or failed output.Medium53
  4. Scope the signal while cranking and running. Look for square edges, full voltage swing and no runt pulses. Missing edges at speed usually mean excess air gap or damaged teeth.Medium3
  5. Safety
    disable ignition or fuel before turning the engine with a wrench, and keep tools and leads clear of belts and fans during cranking tests.Medium7

Symptoms and causes

No signal at any speed

Likely causes Missing supply, open ground, no pull-up, or a failed sensor.

Check Measure supply and ground at the plug, then check the output with a known pull-up fitted.

5

Works cold, drops out hot

Likely causes Sensor electronics failing with heat.

Check Warm the sensor with a heat gun while watching the scope trace.

Medium1

Missing or extra edges at high rpm

Likely causes Air gap beyond spec, damaged teeth or stray magnetic fields.

Check Measure the gap against spec (0.2-1.5 mm for the Mini-HA-P) and inspect the wheel.

3

Dead sensor or ECU input after rewiring

Likely causes Pull-up taken to battery voltage on a 5 V input, or supply polarity reversed.

Check Verify pull-up voltage and polarity before reconnecting.

Medium5

In tuning

Confirm which edge the ECU uses.

The rising and falling edges of a tooth occur at different crank angles, and the difference depends on tooth width. A trigger set up on the wrong edge produces a fixed timing offset that must be found with a timing light.Medium17

Check the pull-up. A missing pull-up gives no signal, and a pull-up to the wrong voltage can exceed the ECU input rating. Many ECUs offer switchable internal pull-ups on trigger inputs for this reason.Medium57

Set the ECU input to digital mode for a Hall sensor. A VR input with adaptive arming expects an AC wave and may mis-trigger on a square wave that never crosses zero.Medium49

Common mistakes

Mistake Leaving out the pull-up resistor.

Do instead Open-collector outputs only pull low. Enable the ECU's internal pull-up or fit one to the specified rail.53

Mistake Feeding a sensor more voltage than its data sheet allows.

Do instead Check the supply range; parts differ, and some engines use 5 V sensors while others use 12 V.Medium56

Mistake Setting the air gap by eye.

Do instead Measure it with feeler gauges against the data sheet; excess gap drops edges at speed.3

Myths vs facts

Myth A Hall sensor produces voltage on its own like a VR sensor.

Fact It needs a supply voltage to operate and usually a pull-up to create its output high level. With no power, it produces no signal at any speed.59

Myth Any three-wire crank sensor is a Hall sensor.

Fact Some three-wire sensors are VR sensors with a shield wire, and some active sensors use magnetoresistive elements. Check the part's data sheet or scope it before wiring.Medium18

Frequently asked

How does a Hall effect sensor work?

A small current flows through a semiconductor element inside the sensor. A magnetic field across it pushes charge to one side, creating a Hall voltage. The chip amplifies that and switches its output when the field crosses set thresholds, so passing teeth or magnet poles turn into a square wave.109

Why does a Hall sensor need a pull-up resistor?

Most automotive Hall sensors have an open-drain or open-collector output that can only pull the signal to ground. A pull-up resistor to a supply provides the high level. Without it, the signal floats and the ECU sees nothing or noise. TI's DRV5013 data sheet describes this open-drain output.5

What are the three wires on a Hall sensor?

Supply voltage, ground and signal output. The supply is often 5 V or 12 V depending on the sensor. Check the data sheet, because feeding 12 V to a 5 V part or pulling the output up to battery voltage can damage it or the ECU input.Medium59

Is a Hall sensor better than a VR sensor?

Neither is better in every case. Hall sensors give clean digital edges at any speed, which helps cranking sync and slow-speed wheel sensing. VR sensors need no power and tolerate higher temperatures, with Bosch rating its IS-C head to 230 °C. The ECU must be set for the type fitted.Medium982

How do you test a Hall effect sensor?

Back-probe it with the connector plugged in. Confirm supply and ground with the key on, then turn the shaft slowly and check that the signal switches between near 0 V and the pull-up voltage. A scope shows dropped or runt edges at speed that a multimeter misses.Medium53

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

10 sources
  1. Crankshaft position sensor · Wikipedia · reference · retrieved 2026-10-27
  2. Inductive Speed Sensor IS-C data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  3. Speed Sensor Hall-Effect Mini-HA-P sealed data sheet 69875339 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. LM1815 adaptive variable reluctance sensor amplifier data sheet (SNOSBU8) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  5. DRV5013 digital-latch Hall effect sensor data sheet (SLIS150) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  6. Dialing in LS sensors for various generations · EngineLabs · press · retrieved 2026-10-27
  7. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  8. Variable reluctance sensor · Wikipedia · reference · retrieved 2026-10-27
  9. Hall effect sensor · Wikipedia · reference · retrieved 2026-10-27
  10. Hall effect · Wikipedia · reference · retrieved 2026-10-27