Variable reluctance (VR) sensor

VR sensormagnetic pickupinductive sensorreluctor sensorpassive speed sensor

A variable reluctance sensor is a passive speed and position sensor made of a magnet and a coil. As teeth on a steel trigger wheel pass its tip, the changing magnetic flux induces an AC voltage. ECUs use VR sensors for crank, cam and wheel speed because they are simple, need no power and tolerate heat.821

How it works

Bosch's IS-C inductive speed sensor is a typical example.

It has a bar magnet, a soft magnetic pole pin and a coil with two connections. A tooth passing the pole changes the flux and induces a voltage proportional to the rate of change; speed is read from the interval between zero crossings.2

Because voltage follows the rate of flux change, amplitude rises roughly with speed and falls with air gap. A usable signal at cranking can be a few hundred millivolts, while the same sensor at high rpm can exceed tens of volts. Bosch specifies an air gap of 0.8 ± 0.3 mm (about 0.03 in) for the IS-C.248

The ECU needs a conditioning circuit to turn that wave into clean edges. TI's LM1815 is an example: it handles inputs from 150 mV to over 120 V peak-to-peak with an external resistor and pairs an adaptive arming threshold with a zero-crossing timing reference.45

The coil is a high-impedance source, so the long lead to the ECU picks up noise easily. Shielded twisted pair, with the shield grounded at one end, keeps ignition and injector interference from adding false teeth.Medium10113

Typical values

Coil resistance (Bosch IS-C)340ΩOther sensors differ; compare with the maker's figureSourced2
Inductance (Bosch IS-C)64mH maximumSourced2
Air gap (Bosch IS-C)0.8± 0.3 mm0.020-0.043 inSourced2
Maximum frequency (Bosch IS-C)15kHzSourced2
Sensing head temperature (Bosch IS-C)-40 to 230°C-40 to 446 °FSourced2
Signal span a conditioner must acceptabout 150 mV to over 120 V peak-to-peakLM1815 input range with external resistorSourced4
Adaptive arming threshold (LM1815)about 80% of the detected peakFixed minimum about 45 mV in its default modeSourced4

How an ECU uses it

A VR conditioner arms when the signal passes a threshold, then fires on the next zero crossing.

The LM1815 derives its threshold from the detected peak, about 80% typical, so a small cranking signal still arms while noise below that level is ignored at high rpm.4

The zero crossing marks the tooth center regardless of amplitude. A fixed voltage threshold would trigger earlier as amplitude grows with rpm, which shows up as ignition timing drifting with engine speed.Medium42

Some ECUs expose the arming threshold as a table against rpm. Too low lets ignition noise count as teeth; too high and the engine will not sync at cranking speed. Hysteresis in the comparator adds margin against chatter around the switching point.Medium45

How to test it

6 checks, in order.

  1. Unplug the sensor and measure coil resistance between the two signal pins. Compare with the maker's figure; the Bosch IS-C reads 340 Ω. Open or near-zero readings mean a failed coil.2
  2. Measure from each signal pin to the sensor body and to ground. Both should read open circuit; any continuity means a shorted coil or chafed harness.Medium28
  3. Set the meter to AC volts and crank. The voltage should appear and rise with cranking speed. A weak reading points to excess air gap, a weak magnet or slow cranking from a tired battery.Medium82
  4. Scope the signal to check polarity and shape. The LM1815 times from the negative-going zero crossing, so confirm the wave crosses in the direction your conditioner expects at each tooth. The missing-tooth gap should appear as a clearly longer, larger swing.Medium4
  5. Check the shield: it should connect to ECU ground at the ECU end only and be open at the sensor end. Then route the cable away from coil and injector wiring.Medium103
  6. Safety
    keep hands and leads clear of belts and fans when cranking, and disable fuel if the engine might start during the test.Medium7

Symptoms and causes

Cranks with no rpm signal or late sync

Likely causes Air gap too large, slow cranking, open coil or arming threshold set too high.

Check Scope cranking amplitude against the threshold and measure coil resistance and gap.

Medium24

Timing drifts as rpm rises

Likely causes Reversed polarity or a conditioner triggering on a fixed threshold rather than the zero crossing.

Check Check timing with a light at idle and at higher rpm; a changing offset confirms it.

Medium48

Misfires, false rev-limit cuts or sync loss at high rpm

Likely causes Noise exceeding the threshold, shield grounded at both ends, or wiring routed near coils.

Check Scope at the failing rpm and look for spikes aligned with spark events.

Medium310

Intermittent sync loss over bumps

Likely causes Loose sensor or bracket changing the gap, or damaged teeth.

Check Check sensor mounting torque, gap and wheel condition.

Medium2

In tuning

Polarity matters.

The accurate timing reference is the zero crossing as a tooth centers on the pole, and conditioners trigger on one direction of crossing. Reversed wires move the detected edge to the wrong side of the tooth, which shows as a timing offset that may change with rpm.Medium48

Use shielded twisted-pair wire with the shield grounded at the ECU end only, and route it away from coil and injector wiring. Noise on a VR line looks like extra teeth, causing sync loss, misfires or false rev-limiter cuts.Medium10117

Check frequency headroom against tooth count and rev limit. A 60-2 wheel at 8,000 rpm gives 8,000 Hz, inside the IS-C's 15 kHz rating, but the signal amplitude at that speed must also stay within the conditioner's input limit.24

Common mistakes

Mistake Grounding the shield at both ends.

Do instead That creates a ground loop that injects noise. Ground it at the ECU end only.Medium10

Mistake Setting the air gap by eye.

Do instead Use feeler gauges and the maker's figure; the IS-C wants 0.8 ± 0.3 mm. Too wide loses cranking signal; too close risks contact.2

Mistake Running unshielded wire next to coil packs.

Do instead Use shielded twisted pair and separate routing. GM fixed a crank-signal stalling fault with a twisted-pair jumper harness.Medium311

Myths vs facts

Myth A VR sensor outputs a square wave like a Hall sensor.

Fact It outputs an analog AC wave whose amplitude and frequency both change with speed. The square wave comes from the ECU's conditioning circuit, not the sensor.82

Myth If the engine runs, VR polarity is correct.

Fact Engines often run with reversed polarity, but the trigger edge moves, so actual timing differs from commanded timing. Confirm with a timing light and a scope.Medium48

Myth A bigger air gap only weakens the signal.

Fact It also changes the waveform shape and can shift edge timing. Set the gap to the sensor maker's specification.Medium28

Frequently asked

How does a VR sensor work?

A permanent magnet sets up a magnetic field through a pole piece wrapped in a coil. When a steel tooth approaches and leaves the pole, the magnetic reluctance changes, so the flux changes and the coil produces a voltage. The voltage swings positive then negative, crossing zero as the tooth centers on the sensor.82

What is the difference between a VR and Hall sensor?

A VR sensor is passive: two wires, no power, and an AC output that grows with speed. A Hall sensor is active: it needs a supply and usually gives a clean digital square wave at any speed, including zero. VR suits harsh heat; Hall gives better low-speed signals.896

Does VR sensor polarity matter?

Yes. The precise timing reference is the zero crossing in one direction. If the two wires are swapped, the ECU detects the opposite edge, which shifts the trigger point relative to the tooth and causes a timing error that can vary with rpm or prevent sync entirely.Medium48

Why does my VR crank sensor not work at cranking speed?

At low speed the flux changes slowly, so the voltage may be too small for the ECU's threshold. Common causes are an excessive air gap, a weak battery slowing cranking, a damaged sensor or a conditioner threshold set too high. Check the gap and scope the signal while cranking.Medium24

How do you test a VR sensor?

Unplug it and measure coil resistance against spec, about 340 Ω for a Bosch IS-C, then check that neither pin shorts to the body. Next, read AC volts while cranking; the voltage should rise with speed. A scope confirms polarity, the missing-tooth gap and any noise spikes.Medium24

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

11 sources
  1. Crankshaft position sensor · Wikipedia · reference · retrieved 2026-10-27
  2. Inductive Speed Sensor IS-C data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  3. Service Bulletin 17-NA-317: crankshaft position sensor circuit EMI, twisted-pair jumper harness (Feb 2020) · General Motors (via NHTSA) · oem · retrieved 2026-10-27
  4. LM1815 adaptive variable reluctance sensor amplifier data sheet (SNOSBU8) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  5. Non-inverting comparator with hysteresis circuit (SBOA313) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  6. DRV5013 digital-latch Hall effect sensor data sheet (SLIS150) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  7. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  8. Variable reluctance sensor · Wikipedia · reference · retrieved 2026-10-27
  9. Hall effect sensor · Wikipedia · reference · retrieved 2026-10-27
  10. Shielded cable · Wikipedia · reference · retrieved 2026-10-27
  11. Twisted pair · Wikipedia · reference · retrieved 2026-10-27