Crankshaft position sensor (CKP)

CKP sensorcrank sensorcrank position sensorCPScrank angle sensorengine speed sensor

A crankshaft position sensor is the sensor that tells the engine computer how fast the crankshaft turns and where it is in its rotation. It reads teeth on a trigger wheel using a variable reluctance or Hall-effect element. The ECU times every spark and injection from it, so a dead CKP sensor usually means no start.18

How it works

A CKP sensor faces a toothed steel wheel on the crank snout, flywheel or harmonic balancer.

Each passing tooth changes the magnetic field at the sensor tip, and the sensor turns that change into a pulse. Pulse frequency gives engine speed; counting pulses from a reference point gives crank angle.18

Two sensing principles dominate. A variable reluctance (VR) sensor is a magnet and coil that generates its own AC voltage, which grows with speed. A Hall-effect or magnetoresistive sensor is powered, can detect a static field and outputs a square wave that stays usable down to zero rpm.123

The wheel carries a reference feature, usually a gap of missing teeth. Bosch specifies its IS-C sensor against a 60-2 wheel: 60 tooth positions 6 degrees apart with two left out. The ECU finds the long gap, then counts teeth to know crank angle.28

Crank angle repeats every revolution, but a four-stroke cycle takes two. The ECU pairs the crank signal with a cam sensor to tell the compression stroke from the exhaust stroke, which sequential injection and coil-on-plug ignition need. Without cam phase, many systems fall back to wasted spark and batch-fire injection.Medium18

Typical values

VR coil resistance (Bosch IS-C)340ΩOther VR sensors differ; use the maker's figureSourced2
VR air gap (Bosch IS-C)0.8± 0.3 mm0.020-0.043 inSourced2
Hall air gap (Bosch Mini-HA-P)0.2-1.5mm0.008-0.059 inSourced3
Hall supply (Bosch Mini-HA-P)5-18 V at about 10 mAOpen-collector output, specified with a 1 kΩ pull-upSourced3
Reference wheel (Bosch IS-C spec)60-2 teeth on a 160.43 mm wheel6.32 inSourced2
GM LS crank patterns24x (Gen III, 12 V sensor) and 58x (Gen IV, 5 V sensor)Sourced · medium7
VR signal spanabout 150 mV to over 120 V peak-to-peakInput range of TI's LM1815 VR conditionerSourced5

How an ECU uses it

Engine speed comes from the time between teeth.

Position comes from counting teeth after the missing-tooth gap, and the ECU interpolates between teeth assuming steady speed. Spark and injection events are scheduled as crank angles, then converted to time using the latest tooth period.Medium81

The ECU also checks plausibility. It expects a fixed tooth count between gaps and a consistent relationship to the cam signal. Extra or missing teeth cause a sync loss that cuts spark and fuel until the pattern is found again.

Some GM ECUs even check crank direction and log P034B when it looks wrong.Medium48

Crank speed rises and falls slightly as each cylinder fires, so OEM strategies use those fluctuations to detect misfire, which US on-board diagnostics require. A noisy crank signal can therefore set misfire codes on a healthy engine.Medium128

How to test it

6 checks, in order.

  1. Start with a scan tool. Crank the engine and watch the rpm reading. A healthy CKP circuit shows a steady cranking speed; zero rpm while the engine turns points to the sensor, its wiring, its supply or the trigger wheel.Medium18
  2. Identify the sensor type before probing. Two wires usually means VR; three wires usually means a powered Hall or magnetoresistive sensor, though some three-wire VR sensors add a shield. Take the pinout from the service information or the crank sensor hub page.Medium110
  3. For a VR sensor, unplug it and measure coil resistance against the maker's figure; the Bosch IS-C reads 340 Ω. Then set the meter to AC volts and crank. The voltage should appear and rise with cranking speed.29
  4. For a Hall sensor, back-probe with the connector plugged in. Confirm supply and ground with the key on, then crank and look for the signal switching between near 0 V and the pull-up voltage. A meter averages this, so use a scope or logic probe.36
  5. For the definitive test, scope crank and cam together while cranking and at idle. Look for a clean missing-tooth gap, even tooth spacing, no spikes near ignition events, and the cam edge landing in the same place every cycle.Medium48
  6. Safety
    keep hands, leads and the scope clear of belts and fans while cranking, and disable fuel or ignition if the engine might start. Use back-probe pins rather than piercing insulation, which lets moisture into the crank circuit.Medium8

Symptoms and causes

Cranks but will not start; scan tool shows no rpm

Likely causes Failed sensor, open wiring, missing supply to a Hall sensor, or a damaged trigger wheel.

Check Scope while cranking. No output with good supply and ground condemns the sensor or wheel.

Medium13

Stalls or will not restart hot, fine after cooling

Likely causes Heat-sensitive sensor electronics or a winding that opens when hot.

Check Reproduce the fault hot and compare rpm data and scope trace with cold readings.

Medium1

Misfire codes, rough running or random cut at high rpm

Likely causes Ignition noise adding false teeth, excess air gap, or reversed VR polarity.

Check Scope at the failing rpm: spikes near spark events mean noise; a shrinking signal means air gap.

Medium45

Crank direction code, low idle or stall after auto start

Likely causes Electromagnetic interference coupled into the crank circuit from other circuits in the same harness.

Check Inspect routing and grounds. GM's fix was a twisted-pair jumper harness from sensor to ECM.

4

Tachometer drops out or jumps while driving

Likely causes Intermittent connector, chafed wire or corroded pins.

Check Wiggle-test the harness while watching live rpm.

Medium1

In tuning

On a standalone ECU, the crank input setup comes first: tooth count, missing teeth, sensor type, trigger edge and the angle from the gap to top dead center. One wrong setting means no sync or a fixed timing error, so confirm base timing with a timing light.Medium81

Swaps often mix generations. GM Gen III LS engines use a 24x wheel and 12 V sensor, Gen IV engines use 58x and a 5 V sensor, and the factory ECUs are not interchangeable without a converter. Match sensor, wheel and ECU input, not just the connector.Medium7

Check the ECU's maximum input frequency against wheel teeth and rev limit. A 60-2 wheel at 8,000 rpm produces 8,000 Hz, inside the IS-C's 15 kHz rating, while a VR signal at that speed can reach tens of volts.25

Formula and worked example

f = N × rpm ÷ 60
f
trigger signal frequencyHz
N
tooth positions on the crank wheel (60 on a 60-2 wheel)
rpm
engine speedrev/min
28

Common mistakes

Mistake Swapping VR sensor wires because the engine still runs.

Do instead Polarity decides which zero crossing the ECU times from. Confirm the edge on a scope and verify timing with a light at idle and higher rpm.Medium59

Mistake Running the crank signal in the same loom as coil or injector wires.

Do instead Use shielded twisted pair, ground the shield at the ECU end only, and route it away from ignition wiring.Medium411

Mistake Replacing the sensor for every crank code.

Do instead Check supply, ground, connector pins and the trigger wheel first; corroded pins and broken wires cause the same faults.Medium1

Mistake Fitting a sensor with the right thread but the wrong type or supply voltage.

Do instead Confirm whether the ECU input expects VR or Hall and what supply it provides. LS 24x and 58x sensors look alike but are not equivalent.Medium7

Myths vs facts

Myth The crank sensor only gives the ECU engine rpm.

Fact It also gives crank angle. The ECU times every spark and injection from tooth position, which is why a failed CKP stops the engine rather than only the tachometer.18

Myth If the CKP resistance is in spec, the sensor is good.

Fact Resistance applies only to VR coils and only proves the winding is continuous. Heat faults, a weak magnet, noise and a wrong air gap all pass a resistance test, so scope the output.Medium12

Myth Crank and cam sensors do the same job.

Fact They may use the same technology, but the cam sensor reads a wheel turning at half crank speed to identify the stroke. The crank sensor provides the fine angle and speed.18

Frequently asked

What does a crankshaft position sensor do?

It reports crankshaft speed and angle to the engine computer. The ECU counts trigger wheel teeth from a reference gap to know where each piston is, then times spark and injection from that position. It is also the main rpm source for the tachometer and the misfire monitor.18

What are the symptoms of a bad crankshaft position sensor?

Typical signs are cranking with no start, stalling that often happens hot and clears after cooling, rough running or misfires, hesitation, and a tachometer that reads zero while cranking. Damaged wiring and corroded connector pins cause the same symptoms, so test the circuit before replacing the sensor.Medium1

Can a car run without a crankshaft position sensor?

Usually not. Most engines need the crank signal to fire the spark and injectors, so they stall or will not start. Some ECUs can limp on the cam signal alone, with coarse timing. Treat a crank sensor fault as a repair-before-driving problem.Low18

How do you test a crankshaft position sensor?

Watch rpm on a scan tool while cranking, then test by type. A two-wire VR sensor should show coil resistance near spec and an AC voltage while cranking. A three-wire Hall sensor needs supply and ground and should then switch its signal. A scope trace of the tooth pattern is definitive.Medium231

What is the difference between a CKP and a CMP sensor?

The CKP (crankshaft position) sensor reads a wheel on the crank and gives speed and crank angle every revolution. The CMP (camshaft position) sensor reads a cam wheel turning at half speed, which tells the ECU which stroke each cylinder is on. Sequential injection and coil-on-plug ignition need both.18

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

12 sources
  1. Crankshaft position sensor · Wikipedia · reference · retrieved 2026-10-27
  2. Inductive Speed Sensor IS-C data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  3. Speed Sensor Hall-Effect Mini-HA-P sealed data sheet 69875339 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. Service Bulletin 17-NA-317: crankshaft position sensor circuit EMI, twisted-pair jumper harness (Feb 2020) · General Motors (via NHTSA) · oem · retrieved 2026-10-27
  5. LM1815 adaptive variable reluctance sensor amplifier data sheet (SNOSBU8) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  6. DRV5013 digital-latch Hall effect sensor data sheet (SLIS150) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  7. Dialing in LS sensors for various generations · EngineLabs · press · retrieved 2026-10-27
  8. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  9. Variable reluctance sensor · Wikipedia · reference · retrieved 2026-10-27
  10. Hall effect sensor · Wikipedia · reference · retrieved 2026-10-27
  11. Shielded cable · Wikipedia · reference · retrieved 2026-10-27
  12. 40 CFR 86.1806-05: On-board diagnostics · US Electronic Code of Federal Regulations · standard · retrieved 2026-10-27