GM · Hall effect (digital)

GM 12591720 camshaft position sensor (Gen IV LS, 4X)

GM 12591720Delphi SS11370NTK EC0321

GM 12591720 is the Gen IV LS camshaft position sensor, mounted in the front timing cover and reading a four-pulse (4X) cam target, from the 5.3/6.0 trucks to the LS3, LS7, LSA and LS9. Gen III engines used a single-pulse sensor at the back of the block instead, so the two are not swappable without changing the ECU pattern.Medium645

Key specifications

Measures: Cam phase (4 pulses per cam revolution). Output: Hall effect (digital).

LocationFront timing coverGen IVSourced · medium6
PatternFour-pulse cam targetSourced · medium6
Cross-referencesDelphi SS11370, NTK EC0321Sourced · medium5
Sensor technologyHall3-wire, inferredResearched, unverified
Part numberMakerNote
12591720GMReplaces 12568983, 12585545Medium45
SS11370DelphiMedium5
EC0321NTKMedium5

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Trigger setup

  • Trigger type: Hall effect (digital square wave).645
  • Pattern: Four-pulse cam target.6
  • Trigger edge: not published by the maker. Confirm the edge your ECU uses with a scope or a timing light before running the engine.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedCRANK (pin 13) or CAM (pin 15) accept Hall in the concept, but the pull-up on these inputs is still an open item.Medium7
Haltech (Elite / Nexus)Configurable (generic input)Trigger or Home input in digital mode with the 5 V pull-up selected.Medium10
Link (G4X)Configurable (generic input)Trigger input; Link sells a Hall sensor kit listed for all Link ECUs.Medium11
MoTeC (M1)UnverifiedThe M150 page lists programmable digital inputs but does not name Hall trigger sensors.No public source
ECUMaster (EMU Black)Configurable (generic input)Trigger input (3: primary and 2 cams), Hall or VR selected in software.12
AEM (Infinity)Configurable (generic input)Crank or cam Hall input (10 kΩ pull-up to 12 V per AEM).13
MaxxECUConfigurable (generic input)Trigger input in digital mode, or an extra digital input for speed sensors.14
Holley (Terminator X / EFI)Configurable (generic input)Crank or cam input; Holley recommends Hall sensors.15

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

Three wires to the ECU cam input; route away from coil wiring.Medium1

Failure modes and checks

Long crank, no sequential sync

Likely cause Cam signal missing or wrong pattern set

Check Log the cam input while cranking; expect four pulses per cam turn.Medium6

Cam sensor oil seep

Likely cause Damaged O-ring

Check Replace the O-ring when refitting the sensor.Low1

Frequently asked

Where is the cam sensor on a Gen IV LS?

In the front timing cover. Gen III LS engines put it at the back of the block.Medium6

Are early LS2 engines 1X or 4X?

EngineLabs notes some early LS2 applications were 24x with the cam sensor in the timing cover, so check the reluctor and cam target, not just the sensor position.Medium6

Related

Use it with GAINS

GM 12591720 camshaft position sensor (Gen IV LS, 4X) on GAINS hardware

ECU2CAM (VR or Hall, single-ended)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable, shield to sensor ground at the ECU end only.Medium7

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.78

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

15 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. OEM sensors GM Camaro: GM part numbers for Camaro knock/crank/cam/MAF/MAP/O2 sensors by year and engine (L98, LT1, LS1, LS3, LSA, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  3. OEM sensors GM Corvette: GM part numbers for Corvette knock/crank/cam/MAP/MAF/O2 1984-2024 (L98, LT1, LS1, LS6, LS2, LS3, LS7, LS9, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  4. OEM sensors GM Silverado: GM part numbers for Silverado gas V8 knock/MAP/MAF/O2/crank/cam 1999-2024 (Gen III/IV/V truck) · gmpartsgiant.com · oem · retrieved 2026-10-25
  5. GM sensors retailer catalogue: Genuine GM / Delphi / NTK / Denso / ACDelco LS and LT sensor listings with fitment titles (24x/58x crank, cam, · michiganmotorsports.com · vendor-doc · retrieved 2026-10-25
  6. Dialing in LS sensors for various generations with Michigan Motorsports · EngineLabs · press · retrieved 2026-10-27
  7. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  8. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  9. GM Genuine Parts (Chevrolet) catalogue listing · GM Genuine Parts (Chevrolet) · oem · retrieved 2026-10-27
  10. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  11. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  12. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  13. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  14. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.