GM · Hall effect (digital)

GM 12703627 58x crankshaft position sensor (Gen IV LS)

GM 12703627Delphi SS11397NTK EH0403

GM 12703627 is the crank sensor for Gen IV LS engines with a 58x reluctor, from the 5.3 and 6.0 trucks to the LS3, LS7, LSA and LS9. EngineLabs describes 58x sensors as gray, 5-volt parts and Gen III 24x sensors as black, 12-volt parts, mounted in the same place with differently keyed connectors. Colour is no longer a reliable guide.Medium645

Key specifications

Measures: 58x reluctor wheel teeth (engine speed and crank angle). Output: Hall effect (digital).

Reluctor58xSourced · medium56
Supply5Vper EngineLabsSourced · medium6
LocationPassenger-side lower rear of the blockSourced · medium6
Cross-referencesDelphi SS11397, NTK EH0403Sourced · medium5
Sensor technologyHall3-wire, inferred from supply requirementGM does not state the technology in a public document we archived.Researched, unverified
Part numberMakerNote
12703627GMReplaces 12585546Medium456
SS11397DelphiMedium5
EH0403NTKMedium5

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Trigger setup

  • Trigger type: Hall effect (digital square wave).645
  • Reluctor: 58x.56
  • Trigger edge: not published by the maker. Confirm the edge your ECU uses with a scope or a timing light before running the engine.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedCRANK (pin 13) or CAM (pin 15) accept Hall in the concept, but the pull-up on these inputs is still an open item.Medium8
Haltech (Elite / Nexus)Configurable (generic input)Trigger or Home input in digital mode with the 5 V pull-up selected.Medium11
Link (G4X)Configurable (generic input)Trigger input; Link sells a Hall sensor kit listed for all Link ECUs.Medium12
MoTeC (M1)UnverifiedThe M150 page lists programmable digital inputs but does not name Hall trigger sensors.No public source
ECUMaster (EMU Black)Configurable (generic input)Trigger input (3: primary and 2 cams), Hall or VR selected in software.13
AEM (Infinity)Configurable (generic input)Crank or cam Hall input (10 kΩ pull-up to 12 V per AEM).14
MaxxECUConfigurable (generic input)Trigger input in digital mode, or an extra digital input for speed sensors.15
Holley (Terminator X / EFI)Configurable (generic input)Crank or cam input; Holley recommends Hall sensors.16

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

Three wires: supply, ground and signal. Keep the crank circuit away from other switching circuits; GM has fixed crank-signal interference on other engines with a twisted-pair harness.Medium76

Failure modes and checks

No start after a Gen III to Gen IV parts swap

Likely cause 24x sensor on a 58x reluctor or 58x on 24x

Check Match the sensor to the reluctor; connectors are keyed differently.Medium6

Intermittent stall

Likely cause Connector or harness damage near the starter

Check Inspect the harness and connector lock at the sensor.Low1

Frequently asked

What is the difference between 24x and 58x crank sensors?

They read different reluctor wheels. EngineLabs: Gen III 24x sensors are black and 12 V; Gen IV 58x sensors are gray and 5 V, with differently keyed connectors in the same location.Medium6

Can I use a 58x sensor on a 24x engine?

Not with the factory ECU: the sensor must match the reluctor and the ECU's expected pattern. Trimming the connector key makes them plug in, but that does not make them interchangeable.Medium6

Related

Use it with GAINS

GM 12703627 58x crankshaft position sensor (Gen IV LS) on GAINS hardware

ECU2CRANK (VR or Hall, single-ended, adaptive threshold)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable, shield to sensor ground at the ECU end only. Hall pull-up arrangement to be confirmed in the schematic.Medium8

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.89

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

16 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. OEM sensors GM Camaro: GM part numbers for Camaro knock/crank/cam/MAF/MAP/O2 sensors by year and engine (L98, LT1, LS1, LS3, LSA, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  3. OEM sensors GM Corvette: GM part numbers for Corvette knock/crank/cam/MAP/MAF/O2 1984-2024 (L98, LT1, LS1, LS6, LS2, LS3, LS7, LS9, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  4. OEM sensors GM Silverado: GM part numbers for Silverado gas V8 knock/MAP/MAF/O2/crank/cam 1999-2024 (Gen III/IV/V truck) · gmpartsgiant.com · oem · retrieved 2026-10-25
  5. GM sensors retailer catalogue: Genuine GM / Delphi / NTK / Denso / ACDelco LS and LT sensor listings with fitment titles (24x/58x crank, cam, · michiganmotorsports.com · vendor-doc · retrieved 2026-10-25
  6. Dialing in LS sensors for various generations with Michigan Motorsports · EngineLabs · press · retrieved 2026-10-27
  7. Service Bulletin 17-NA-317: crankshaft position sensor circuit EMI, twisted-pair jumper harness (Feb 2020) · General Motors (via NHTSA) · oem · retrieved 2026-10-27
  8. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  9. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  10. GM Genuine Parts (Chevrolet) catalogue listing · GM Genuine Parts (Chevrolet) · oem · retrieved 2026-10-27
  11. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  12. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  13. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  14. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  15. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.