GM · Hall effect (digital)

GM 12560228 24x crankshaft position sensor (Gen III LS)

GM 12560228NTK EH0157

GM 12560228 (replacing 12555566) is the crank sensor GM lists for Gen III LS engines with a 24x reluctor: LS1, LS6 and early 4.8/5.3/6.0 trucks. EngineLabs describes 24x sensors as black, 12-volt parts. They mount in the same spot as the later 58x sensor but are not interchangeable with it.Medium145

Key specifications

Measures: 24x reluctor teeth. Output: Hall effect (digital).

Reluctor24xSourced · medium4
Supply12Vper EngineLabsSourced · medium5
Sensor technologyHall3-wire, inferredThe catalog notes the source did not state the type.Researched, unverified
Part numberMakerNote
12560228GMReplaces 12555566Medium14
EH0157NTKMedium4

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Trigger setup

  • Trigger type: Hall effect (digital square wave).145
  • Reluctor: 24x.4
  • Trigger edge: not published by the maker. Confirm the edge your ECU uses with a scope or a timing light before running the engine.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedCRANK (pin 13) or CAM (pin 15) accept Hall in the concept, but the pull-up on these inputs is still an open item.Medium6
Haltech (Elite / Nexus)Configurable (generic input)Trigger or Home input in digital mode with the 5 V pull-up selected.Medium9
Link (G4X)Configurable (generic input)Trigger input; Link sells a Hall sensor kit listed for all Link ECUs.Medium10
MoTeC (M1)UnverifiedThe M150 page lists programmable digital inputs but does not name Hall trigger sensors.No public source
ECUMaster (EMU Black)Configurable (generic input)Trigger input (3: primary and 2 cams), Hall or VR selected in software.11
AEM (Infinity)Configurable (generic input)Crank or cam Hall input (10 kΩ pull-up to 12 V per AEM).12
MaxxECUConfigurable (generic input)Trigger input in digital mode, or an extra digital input for speed sensors.13
Holley (Terminator X / EFI)Configurable (generic input)Crank or cam input; Holley recommends Hall sensors.14

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

  • Parts catalogueOfficial parts-catalogue listing (no data sheet or CAD published)Medium8Download from GM Genuine PartsNo login at last check; the maker may change this

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

Supply it from the voltage it expects (12 V per EngineLabs); a 5 V-only input supply will not run it.Medium5

Failure modes and checks

No rpm signal

Likely cause Sensor fed 5 V instead of 12 V

Check Measure supply at the connector.Medium5

Wrong pattern

Likely cause 58x sensor fitted to a 24x engine

Check Match the sensor to the reluctor.Medium5

Frequently asked

What crank sensor does an LS1 use?

GM 12560228 (replacing 12555566), a 24x sensor.Medium14

What supply does a 24x LS crank sensor need?

12 V, per EngineLabs; the later 58x sensors run on 5 V.Medium5

Related

Use it with GAINS

GM 12560228 24x crankshaft position sensor (Gen III LS) on GAINS hardware

ECU2CRANK (VR or Hall, single-ended, adaptive threshold)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable, shield to sensor ground at the ECU end only. Hall pull-up arrangement to be confirmed in the schematic.Medium6

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.67

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

14 sources
  1. OEM sensors GM Camaro: GM part numbers for Camaro knock/crank/cam/MAF/MAP/O2 sensors by year and engine (L98, LT1, LS1, LS3, LSA, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  2. OEM sensors GM Corvette: GM part numbers for Corvette knock/crank/cam/MAP/MAF/O2 1984-2024 (L98, LT1, LS1, LS6, LS2, LS3, LS7, LS9, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  3. OEM sensors GM Silverado: GM part numbers for Silverado gas V8 knock/MAP/MAF/O2/crank/cam 1999-2024 (Gen III/IV/V truck) · gmpartsgiant.com · oem · retrieved 2026-10-25
  4. GM sensors retailer catalogue: Genuine GM / Delphi / NTK / Denso / ACDelco LS and LT sensor listings with fitment titles (24x/58x crank, cam, · michiganmotorsports.com · vendor-doc · retrieved 2026-10-25
  5. Dialing in LS sensors for various generations with Michigan Motorsports · EngineLabs · press · retrieved 2026-10-27
  6. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  7. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  8. GM Genuine Parts catalogue listing · GM Genuine Parts · oem · retrieved 2026-10-27
  9. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  10. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  11. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  12. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  13. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.